Variable Attenuators
Provide changeable resistance values.
-
Product
High Line Pressure Variable Reluctance Pressure Sensor to 10,000 psid
DP360/DP363
-
The DP360 can be calibrated for a full scale as low as ±50 psid while withstanding high static line pressure. Low differential pressure may be measured at static pressures as high as 10,000 psig with a maximum 3% FS zero shift error.
-
Product
Programmable Attenuators
-
JFW offers 50 Ohm and 75 Ohm programmable attenuators with either relay or solid-state designs. 50 Ohm Relay Step Attenuators, 50 Ohm Solid-State Step Attenuators (TTL), 50 Ohm Solid-State Step Attenuators (USB), 75 Ohm Relay Step Attenuators, 75 Ohm Solid-State Step Attenuators, Analog Programmable Attenuators, High Power Solid-State Step Attenuators.
-
-
Product
Digital Attenuators
-
Macom Technology Solutions Holdings Inc.
Digital Step Attenuators (DSA)are offered in up to 6 Bit control with lowest step size of 0.5 dB covering DC to 40 GHz. MACOM's DSAs can be controlled with serial and parallel control allowing for best implementation for our customers. These products exhibit low insertion loss and high attenuation accuracy and are offered both GaAs and Silicon (SOI) processes and are offered in both packaged and bare die form factors.
-
Product
Variable Transformer DC Power Supplies
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with a Variable Transformer (also known as variac). The Variable Transformer can be adjusted manually or with a motorized control. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
Product
Power/Voltage Rail Probe. 4 GHz Bandwidth, 1.2x Attenuation, +/-30V Offset, +/-800mV
RP4030
-
The Teledyne LeCroy RP4030 Power Rail Probe meets the specific requirements of those who need to acquire a low-voltage DC signal as part of a:-Comprehensive power integrity, digital power management IC (PMIC), voltage regulator module (VMR), point-of-load (POL) switching regulator, or low-dropout regulator testing- Complete embedded power management system that includes PMICs, VRMs, POLs, and LDOsThe RP4030 will faithfully acquire a low-impedance, low-voltage DC power/voltage rail signal without unduly loading the device under test (DUT), while providing high offset to allow DC power/voltage rail signal display on an oscilloscope with high gain.
-
Product
Digital Control Step Attenuator
-
Digital control attenuators with TTL parallel control offering fast switching speed and high attenuation accuracy
-
Product
Power/Voltage Rail Probe, 2 GHz Bandwidth, 1.2x Attenuation, +/-60V Offset, +/-800mV
RP2060
-
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
Product
10-amp AC and DC Variable Power Supply
ACDC-10
-
The ETI Model ACDC-10 is a small, lightweight, and portable AC and DC power supply. The unit is intended for resetting circuit breaker charging motors and other general-purpose applications. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 1.4 kVA. The ACDC-10 is housed in a rugged plastic enclosure approximately 20” x 11” x 18” and weighs less than 65 lbs
-
Product
CAT-5 Video Variable Filters
-
It is often beneficial to use a video driver at the output of a video encoder for power savings, line driving, and additional circuit protection. The video driver is typically configured as an active filter, also known as a reconstruction or anti-imaging filter. The purpose of the reconstruction filter is twofold: it blocks the higher frequency components (above the Nyquist frequency) that were introduced into the video signal as part of the digitization process and provides gain to drive the external 75 Ω cable to the video display.
-
Product
Coaxial Dynamics RF Attenuators
-
Coaxial Dynamics RF Attenuators offer a reliable and accurate method for reducing RF power levels. All of our designs dry convection cooled and can be used in any position.
-
Product
Manual Attenuator (Waveguide)
-
Manual control waveguide attenuators in both variable (continuous) or stepped in a variety of frequencies, attenuation values / step sizes and power levels
-
Product
Telephone Attenuators & RFI Filters
-
Despite the growth in digital and fiber systems, many telephone companies still require basic line treatment products. Wilcom's hard-to-find line treatment products help the telecommunications industry deliver the performance the customer expects. Products include line powered amplifiers and RFI filters.
-
Product
Cryogen Free Variable Temperature Cryostat for EPR
-
We offer a variable temperature cryostat with a sample space of 40mm designed to fit between the poles of a resistive electromagnet for EPR applications. The cryostat is designed to receive standard EPR probes.
-
Product
Attenuator Interconnect Kit, SMA
11716C
Interconnect Adapter
The Keysight 11716C quickly and conveniently connects 1 dB step and 10 dB step attenuators together to achieve greater dynamic range with 1 dB steps. The Keysight 11716C can be utilized to connect any of the two Keysight 8494/95/96 attenuators in series.
-
