Variable Attenuators
Provide changeable resistance values.
-
Product
HVFO10X +/-20V (20x Attenuation) Universal Tip Accessory
HVFO100-20X-TIP-U
-
HVFO10X +/-20V (20x Attenuation) Universal Tip Accessory.
-
Product
6/12/24 Volt Heavy-Duty Variable Carbon Pile Load Tester
6036B-24
-
• Same features as Model 6036B • PLUS the added value of 24 Volt battery testing capacity• Made in USA of US and Global Components
-
Product
SP500X , 500 MHz, ±300 V, 10X Attenuation, Single-Ended Passive Oscilloscope Probe
783629-01
Oscilloscope Probe
The SP500X, or Multi-Contact Isoprobe IV - 10:1, is a standard passive probe with fixed 10x attenuation for oscilloscopes that provide 1 MΩ input impedance.
-
Product
Power/Voltage Rail Probe, 2 GHz Bandwidth, 1.2x Attenuation, +/-60V Offset, +/-800mV
RP2060
-
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
Product
Attenuators And Pulse Limiters
-
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
Product
Programmable Attenuators
-
JFW offers 50 Ohm and 75 Ohm programmable attenuators with either relay or solid-state designs. 50 Ohm Relay Step Attenuators, 50 Ohm Solid-State Step Attenuators (TTL), 50 Ohm Solid-State Step Attenuators (USB), 75 Ohm Relay Step Attenuators, 75 Ohm Solid-State Step Attenuators, Analog Programmable Attenuators, High Power Solid-State Step Attenuators.
-
Product
Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-60V offset, +/-800mV
RP4060
-
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
Product
Variable Reluctance Pressure Sensor with All-Welded Construction
DP10
-
The DP10 Pressure Sensor, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full scale output of 30 mV per volt at 3kHz. The unit operates with carrier system including the Validyne CD15 since wave carrier demodulator and CD16 miniature DC input DC output carrier demodulator.
-
Product
Precision Programmable Attenuator
RCDAT-30G-30
-
Mini-Circuits’ RCDAT-30G-30 is a precision programmable attenuator covering an extremely wide bandwidth, from 0.1 to 30 GHz. Its unique design allows attenuation settings to be programmed from 0 to 30 dB, in 0.5 dB steps with monotonic attenuation change per dB, even at the highest frequencies and attenuation settings. The attenuator can be controlled via USB or Ethernet, allowing control directly from a PC, or remotely over a network. VHF / UHF / L / S / C / X / Ku / K band testing.
-
Product
Variable Reluctance Pressure Sensor Capable of Range Changes
DP15
-
An easy-to-replace pressure-sensing diaphragm maximizes the system's functionality by making pressure measurements from 2.22" H2O to 3200 psi in one compact unit. Rugged and reliable, the DP15 pressure sensor provides superior accuracy for measuring low-pressure liquids and gasses, while it withstands the abuse of field and laboratory testing. The ability to change full scale ranges make the DP15 a very cost effective solution for applications that need different pressure ranges or university labs.
-
Product
Electromechanical Programmable Attenuators
-
BroadWave manufactures single section 6 dB to 8 section 0 – 127 dB programmable attenuators. •Voltage control and external TTL control •RF Connectors: BNC, N, SMA and TNC •50 and 75 Ohm
-
Product
USB Oscilloscope, Logic Analyzer and Variable Power Supply
Analog Discovery 2
-
Digilent Analog Discovery 2, developed in conjunction with Analog Devices and supported by Xilinx University Program, is a multi-function instrument that allows users to measure, visualize, generate, record, and control mixed signal circuits of all kinds. The low-cost Analog Discovery 2 is small enough to fit in your pocket, but powerful enough to replace a stack of lab equipment, providing engineering students, hobbyists, and electronics enthusiasts the freedom to work with analog and digital circuits in virtually any environment, in or out of the lab. The analog and digital inputs and outputs can be connected to a circuit using simple wire probes; alternatively, the Analog Discovery BNC Adapter and BNC probes can be used to connect and utilize the inputs and outputs. Driven by the free WaveForms 2015 (Mac, Linux and Windows Compatible) software, Analog Discovery 2 can be configured to work as any one of several traditional instruments.
-
Product
Variable Frequency AC Power Supply 500VA 1KA 2KVA 3KVA 5KVA
CX-9000
-
Shenzhen Chuangxin Instruments Co., Ltd.
Variable Frequency AC Power Supply 500VA 1KA 2KVA 3KVA 5KVA
-
Product
0-600 Amp Variable Carbon Pile Load Tester
6039
-
• Test batteries up to 1200 CCA• Fine threaded shaft for fine adjustment• Temperature compensation chart• Easy to read digital voltmeter & ammeter combine with the versatility of a carbon pile load• Spring loaded to shut-off automatically• Unique curved discs to prevent hot spots• Tests all battery types• Made in USA of US and Global Components
-
Product
Fixed Attenuators
-
The Analog Devices family of wideband, fixed value, 50 Ω matched attenuator products offers relative attenuation levels that range up to 20 dB. Our products are ideal for microstrip, hybrid, and multichip module applications that require extremely flat attenuation and excellent VSWR vs. frequency.
-
Product
6/12 Volt Heavy-Duty Variable Carbon Pile Load Tester
6036B
-
• High-volume testing and fleet use• Tests 6/12 Volt batteries• 1000 Amp load; tests batteries up to 2000 cold cranking amps• Cools with high RPM fan for continuous battery testing• High resolution carbon pile assembly for smoother operation and longer life• Optional Model 6038C for added mobility with convenient heavy-duty cart with wheels• Made in USA of US and Global Components
-
Product
Attenuators
-
Flann manufactures a portfolio of both manual and programmable attenuators that cover a wide range of applications and waveguide bands
-
Product
Fixed Attenuator (Coaxial)
-
RF Lambda’s fixed coaxial attenuators are used to adjust the signal level in any RF system. They are most commonly used to reduce high power signals in order to inject into test equipment or other parts of the RF system requiring lower signal levels. They are highly reliable and come in a variety of frequencies, powers, and connectors.
-
Product
Variable Gain Amplifier
VGA
-
RF Lambda’s variable gain amplifiers (VGA) are standard amplifiers which include a gain control pin to allow the customer to tune the gain for various applications without sacrificing performance and eliminating the need to use a separate amplifier and attenuator. Hermetically Sealed options are available upon request.
-
Product
POWER ATTENUATORS
TYPE ATF
-
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Product
DC Bias Attenuators
-
a fixed DC Bias attenuator from Pasternack. This 10dB attenuator is an in-line, resistive PI attenuator pad design. Our coaxial 50 Ohm attenuator is manufactured to precise RF / microwave industry specifications.
-
Product
HVFO10X +/-1V (1x Attenuation) Universal Tip Accessory
HVFO100-1X-TIP-U
-
HVFO10X +/-1V (1x Attenuation) Universal Tip Accessory.
-
Product
C-Band DWDM VGA with Mid-Stage Access Next-Generation Variable Gain EDFA
HWA4700 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4700 series is a next-generation variable gain EDFA, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
Product
Attenuators
-
Shenzhen Tojoin Communication Technology Co., Ltd.
Attenuators are used in a wide variety of applications and can satisfy almost any requirement where a reduction in power is needed. Attenuators are used to extend the dynamic range of devices such as power meters and amplifiers, reduce signal levels to detectors, match circuits and are used daily in lab applications to aid in product design. Attenuators are also used to balance out transmission lines that otherwise would have unequal signal levels.
-
Product
Cryogen Free Variable Temperature Cryostat for EPR
-
We offer a variable temperature cryostat with a sample space of 40mm designed to fit between the poles of a resistive electromagnet for EPR applications. The cryostat is designed to receive standard EPR probes.
-
Product
Variable Area Flow Meters
-
Omega's extensive portfolio of variable area flow meters supports any industrial, medical, lab, or process control application. Let Omega help you select the proper flow meter for your application
-
Product
Handheld Variable Optical Attenuator
VOA100
-
Shanghai Tarluz Telecom Tech Co., LTD
VOA100 handhold optical variable attenuator is used for continuously variable optical signal attenuation. As the VOA100 is used in the laser system for the on-line testing, therefore, it can be used in the digital system of communication devices (such as: PHD, SDH) and also in the system of adopting analog modulation (CATV)
-
Product
Manual Step Attenuator
WATT-3SM352
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customers demand. All Warisons products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Variable Pipe Frame Slide Anvil Type Outside Micrometer
-
Light-weight design using the pipe-structure frame Allows easy measurement of even a large workpiece.
-
