Current
See Also: Direct Current, Alternating Current, Resistivity, Flow, Inductance
-
product
Leakage Test
Leakage current and discharge current depend on the insulation of the device. The measurement simulates various fault situations that could occur during operation. The test determines whether the measured current is within the permissible limits and poses no danger to the user in case of a fault.
-
product
Station Of Acceptance Testing
The acceptance test station consists of a personal computer - the workstation of the operator of the testing station, contact mechanisms, as well as current and voltage sensors. The station allows to test up to 10 electric motors of various types simultaneously. The operator of the testing station indicates the test sites at which the engine tests will be conducted, their type (from the database), serial numbers and a set of tests.
-
product
PXI General Purpose 2A Relay Module 32xSPST
40-132-201
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
product
DC Bias Current Source
TH1778AS
Changzhou Tonghui Electronic Co., Ltd.
■ Test Frequency: 0Hz - 2MHz ■ Provide 0~20A of constant current output, and must be controlled by TH1778A ■ Support 6 machines on line at most and
-
product
Current Transformers
A range of ring type current transformers suitable for primary currents from 1A-5000A with 1A or 5A secondaries. This standard range of measuring and protective current transformers is available as resin coated or tape wrapped.
-
product
Circular Connectors
Complete range of circular connectors with metal and plastic shells, and crimp and solder terminations for multichannel hybrid electrical/ optical insert arrangements, supporting a wide range of allowable contact voltages and currents, easy environmental sealing and rugged mechanical performance.
-
product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Bias Ball Probe
POGO-1J-2
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Adjustable AC Power Meter
APS-6000
The APS-6000 adjustable AC power source is a multi-function AC power source that integrates voltage, current, power and power factors. The internal high-speed processor is a cost-effective, high-stability AC power source.
-
product
Automatic Relay Test Set
DRTS 34
DRTS 34 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 4 Voltage generators simultaneously available.
-
product
High Speed DC Electronic Load
6330A series
The 6330A family offers 8 types of modular loads with power ranging from 30 watts to 1200 watts, current from 0.5mA to 240A, and voltage measurement from 0.5mV to 500V. Each load is isolated and floating, programmable in dual current range and measuring voltage range, and capable of synchronizing with other modules for control operating. The load can be operated in constant current, constant voltage, and constant resistance. With Synchronic parallel control capability, 6330A series loads allow users to parallel and synchronize more than one load together from an internal loading control signal. This feature provides synchronic dynamic loading test for multi-output power and high power test solution. Real time measurement of voltage, current, is integrated into each 6330A load module using a 16-bit precision measurement circuit. The user can perform on line voltage measurement and adjustment, or simulate short circuit test using the simple keypad on the front panel.
-
product
Transmission Line Testers
GAOTek provides affordable, safe and reliable transmission line testers, digital clamp meters and power meters for sale to the United States, Canada and Globally. A transmission line is a specialized cable designed to conduct alternative current of radio frequency. Transmission lines are used for connecting radio transmitters and receivers with their antenna to distribute signals.
-
product
Current Transformers
The Current Transformer (CT) is the sensor which measures the amount of current draw from the wire it is installed on.
-
product
Voltage, Current and Power Measurement
Educated Design & Development, Inc.
For measuring current, especially higher currents and quicker than series ammeters. These units are considered the finest available. All units are extremely rugged, reliable, and versatile.
-
product
Interface Technology ProLine
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation Amplifier for DC voltage and current measurement with galvanic isolation, active and passive standard signal isolation amplifier, supply isolation amplifier for supplying 2-wire sensors, transmitter for temperature and AC signals, isolating amplifiers for high voltages and shunt applications. T
-
product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Bias Ball Probe
POGO-1T30-10
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Elevated 1.68 (48.00) - 7.00 (198.00) High Performance Bias Ball Probe
POGO-1I8-7-S
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Signal, Contact, ITA, TriPaddle,7 Amp, 20-24 AWG
610110108
Primary mating contact 610110101. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. with Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Digital Multimeters
Multi-Display : Primary 80000, Secondary 80000, Bargraph 23 SegmentsBasic DC Accuracy : 0.05% mV Impedence : > 1000M OhmMore than 50 Measuring FunctionsFrequency Measurement : 0.5Hz to 8.0000MHz 16 Frequency Points, 1% to 99% Duty. Selectable Square Wave OutputAnalyzing Component of Current or Voltage SignalResistance : 0.1Ω to 80MΩ, 10MΩ to 8000MΩCapacitance : 1nF to 100µFTemperature : -50°C to 1372°C, -58°F to 2502°F dBm 20 Types of Reference ImpedenceAuto Data Hold / Peak HoldRelative Measurement36 Hours Dynamic Recording : MAX / MIN / AVG/ MAX-MINCommunication : Isolated Optical RS-232Timer for MeasurementBacklight DisplayAuto Power Off
-
product
5 A portable digital micro-ohmmeter
MPK-254
The MPK-254 digital very low resistance ohmmeter is a portable, microprocessor-controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1 mA up to 5 A.
-
product
6TL-3X INLINE Header Conveyor 765 mm Length
AQ580
- PCB up to 600mm length 400 mm width- Programmable transfer speed up to 1 m/s- Automatic Previous/Next speed adjustment- 2D Code reader w/automatic positioning- Pre-wired for second 2D Code reader- Automatic width setting- PC for line management w/UPS with 20” monitor and keypad in adjustable position arm- 24 Ports PoE Switch- Power inlet rack with current protections and line safety relay- Top cover and door w/safety contacts inhibiting line modules while active- Mechanisms self-test- Width auto-adjustment and cyclic width- Non-contact electronic stop of the PCB- 4U Free on the 19” Rack- Interfaces SMEMA 9851 y IPC-HERMES 9852- CE certified
-
product
3-phases Power Analyzers
PeakTech Prüf- und Messtechnik GmbH
s a power analyzer with a large LCD display. Measured power can be recorded with the analyzer, but it is also possible to record and display various voltages, currents, power factors and many other variables. Several electrical variables are attracted during a measurement, so it is possible to show the power and the cos φ at the same time.
-
product
Loading Rheostats (Resistive Load)
Supreme Instrument Laboratories
Loading Rheostat is a device specially designed to meet the requirements of Engineering Laboratories, Electrical Test Rooms and Industries. It is used for loading transformers, power generators, supply mains etc. neatly and efficiently. It can also be used advantageously for regulating current and adjusting voltage besides its application for calibrating meters and thus eliminating the need for graded rheostats.
-
product
Mini Power, Contact, ITA, 65 Amp, 8 AWG
610115124
Primary mating contact 610116112. (May mate with other Receiver contacts, as well.)Mini Power contacts carry up to 65 amps continuous current, 480 VAC. Maximum resistance is 1 Milliohms.Specifications Operating Voltage & Current 65 Amps Max. Continuous – 8 AWG40 Amp Max. Continuous – 12 AWG30 Amp Max. Continuous – 14 AWG25 Amp Max. Continuous – 16 AWGContact Resistance 1 mOhms Max.Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 1000 MOhms Min.Contact Body BeCuContact Plating 50µ" Au over 100µ" NiContact Termination SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 3.37
-
product
PXIe-4051 - PXIe, 1-Channel, 60 V, 40 A PXI Electronic Load Module
788179-01
The PXIe-4051 provides programmable load capable of sinking DC power for characterization, design validation, and manufacturing test. This module helps you sink current and absorb power out of a power source up to 300 W with programmable constant voltage, current, resistance, and power levels. You can use the PXIe-4051 to streamline the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and semiconductor component test—by eliminating the need to mix multiple instrumentation form factors in a given test system and simplifying synchronization.
-
product
Current Transformer
ST-60CT
Standard Electric Works Co., Ltd
● 400/5A - 800/5A● 7.5-10V A● Class 1● Insulation 600V
-
product
1000A AC Clamp Meter
CM55
The CM55 is a pocket sized high performance AC Clamp meter measuring AC current, AC/DC voltage and resistance with continuity test. The compact rugged design enables accurate and reliable current measurement down to 10mA resolution without the need to break into the circuit.The CM55 has a CATIII 600V safety rating and is the ideal tool for residential and commercial electricians.
-
product
Alternate 0.66 (19.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-62J-6
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
High Temperature Operating Life
7000 Series
With ever decreasing geometries, the way we perform HTOL requires careful consideration. In lower geometry device leakage currents are not only higher but vary greatly. Temperature control at DUT level – required to achieve correct junction temperature at every DUT. For higher geometries, HTOL can be performed in a more traditional way but with devices consuming more power, the ambient temperatures required varies greatly. Multiple temperature zones are required – multi zones system or multiple smaller HTOL systems.
-
product
Industrial Universal Testing Machines
Our list of current Industrial Universal Testing Machines products are listed below. If you cannot find what you are looking for, please contact us and we will try our best to help you.
-
product
500 Amps, 2 MHz BW Current Probe - AC/DC , 700 Amp Peak
CP500
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
