Phasing
See Also: Phase, Phase Standards, Phase Meters, Phase Angle, 3 Phase, Sticks, Phasors
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG-HS
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
Cable Assembly with 2.4mm Male Connectors
Y1740A
-
The Y1740A is a flexible cable with excellent phase stability. This cable is recommended for accurate S-parameter measurements using the following Keysight vector network analyzers: Streamline Series VNA, M983xA/M980xA Series PXIe VNA, or M981xAS series PXIe Vector Component Analyzer (VCA).
-
Product
Power RC Snubbers
-
Single phase and Three phase availableSuitable for AC and DC voltage applicationResistance and rate power of Resistor : 1 - 50W ( can be customized to 100W or above )Voltage: 63Vac, 125Vac, 280Vac, 480Vac, 500Vac, 600VacOperating temperature : -25~+85C / -40~+105CTesting Voltage : : 1.5 x Un 10sec ( can be customized )Varistor and Diode options available. Different applications can have very different electrical and mechanical profile requirements.Please feel free to send your application details for a suggestion and quotation.
-
Product
IQ Demodulator
-
Teledyne RF & Microwave IQ Demodulators are fully space-qualified designs providing stringent phase and amplitude matching, and superior output third order intercept performance. To meet high LO and IF rejection requirements diplexers are used at the I and Q ports. All components and processing fully meet MIL-PRF-38534, Class K and MIL-DTL-28837. Teledyne RF & Microwave can provide performance to meet most receiver system requirements, including single or moving LO frequencies and tight phase and amplitude matching. Customers can specify our designs for space, military, or commercial applications.
-
Product
Orotron (High-Power BWO) Based Sources 120 To 370 GHz
-
Insight Product Company offers Orotron based sources of radiation at frequencies 120 to 370 GHz. The Oroton tube is installed inside the permanent magnet and does not require any adjustment by the customer. The Orotron sources are wide-banded, small in size, very reliable, powerful, and easy to operate. We offer phase-locking as an option on our Orotron based sources to maximize the phase and frequency stability.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
783127-01
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
Ocean Observer III
-
Teledyne Marine RD Instruments
Since 1997 Teledyne RD Instruments has been providing ADCPs that have proven in the field they can profile beyond 1000 m from research vessels traveling at speeds >15 knots and from offshore oil and gas platforms during exploration work. That same technology has now allowed us to create the Ocean Observer III 38 kHz ADCP. We have combined our field-proven 38 kHz phased array ADCP transducer with our field-proven electronics into a single package that is capable of profiling >1000m. This design makes it ideal to be mounted from an oil platform, over the side of a vessel, and in surface buoys.
-
Product
Relay Tester
LET-4000-R
-
Regulation and Measurement Module performs the regulation of the DC current and is made with a variable auto transformer (Variac) regulating a three phase DC current, with a power of 8KVA and a three phase transformer of 8KVA with 2V nominal power in the secondary windings. A built-in ammeter and a timer give the information of the current injected and the operation time of the relay under test.
-
Product
15W to 480W - Single Output
DRB Series
-
*Single and Three Phase Input Models*High Efficiency, up to 94%*Peak Power Capability Models, 20% for 2sec*Long E-Capacitor Life*Class 2 Models to UL 1310*Class 1 Div 2 for Hazardous Locations
-
Product
Astronics PXIe-2461, 235 MHz FrequencyTime Interval Counter
784197-01
Counter/Timer Module
PXIe, 42 V, 2-Channel PXI Counter/Timer Module—The Astronics PXIe‑2461 is a high-performance counter/timer module that provides easy-to-use automatic measurement functions, including phase, pulse, peak, rise/fall time, time interval and ratio measurement, all with high resolution. It features nine digits per second resolution, programmable measurement timeout, and nine different arming modes. You can set the Astronics PXIe-2461 to measure timing and amplitude characteristics in one of two voltage ranges: ±5.1 V or ±42 V.
-
Product
Phase Angle Voltmeter
PAV1010A
-
Measuring Vrms, inphase, quadrature, freq, ratios and phase angles. Using Discrete Fourier Transform algorithms, the PAV1010A provides capability, performance and versatility not available with traditional PAVs. Targeted at the Synchro/Resolver and LVDT/RVDT marketplace, this instrument makes measurements of Phase Angle, In-Phase, Quadrature (90° component), Fundamental and Total Vrms very straightforward. All these measurements are displayed simultaneously on a bright multifunction display.
-
Product
Pulsed And CW EPR/ESR: Synthesizers Up To 280 GHz
-
Insight Product Company offers synthesizers at frequencies from 30 to 280 GHz which can be used in EPR/ ESR experiments. These sythnesizers are designed to go swiftly from the generation to the non-generation mode and back. This process is controlled by external TTL signal. There is also the possibility to manipulate the phase, namely to shift it by 90 degrees and 180 degrees. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
Ultrasonic Thickness Gauge
UTG-1500
-
The new PHASE II UTG-1500 is a hand held microprocessor controlled ultrasonic thickness gauge specifically designed for measuring the thickness of metallic and non-metallic materials such as aluminum, titanium, plastics, ceramics, glass and any other good ultrasonic wave-conductor as long as it has parallel top and bottom surfaces.
-
Product
Cable Assemblies
-
We offer a variety of cables covering DC to 110Ghz. Cable assemblies from 0-6Ghz we usually build in our Quick Turn Cable Assembly Shop, delivery is 1-2 days. We also offer some Low Loss Phase Stable from our quick turn shop; but some of the precision cables can take longer.
-
Product
AC Source
AMF
-
The Intepro AMF Series is a complete line of single and three phase, 400Hz AC Frequency Converter products. With Power levels ranging from 6kVA up to 300kVA, the AMF series of frequency converter products are the ideal and cost effective solutions for precise frequency conversion in all avionics and higher frequency electronic applications. Power and frequency conversion is supplied by state-of-the-art IGBT pulse-width-modulated power amplifiers resulting in highly efficient power conversion, compact design and maximized performance with minimum downtime.
-
Product
Low Phase Noise Amplifier
-
RF Lambda’s lower phase noise amplifier offerings include special power supply conditioning and utilize technology to reduce the phase noise addition from amplifying the signal. Hermetically sealed options are available upon request.
-
Product
Transmissive Optical Encoder Module
EM1
-
The EM1 is a transmissive optical encoder module designed to be an improved replacement for the Avago HEDS-9000 series encoder module. This module is designed to detect rotary or linear position when used together with a code wheel or linear strip. The EM1 consists of a lensed LED source and a monolithic detector IC enclosed in a small polymer package. The EM1 uses phased array detector technology to provide superior performance and greater tolerances over traditional aperture mask type encoders.
-
Product
9kHz to 20/40GHz Signal Generator
CSG Series
-
Corech Microwave’s CSG series of Compact Microwave Signal Generators（Signal Source）operate from 9kHz to 20GHz / 40GHz. It offers high dynamic output power -120 to +17dBm, ultra low phase noise: -105dBc/Hz@10KHz, low harmonics and spurious. These exceptional performances make CSG9K20GA / CSG9K40GA an ideal choice for many test and measurement applications, including Semiconductor, Quantum Technology, Radar and Communication etc.
-
Product
Single Phase Din-rail kWh Meter
SY 1018
-
Hong Kong Songyang Industrial Ltd.
Type SY1018 single phase DIN watt-hour meter is a kind of new style single phase electronic watt-hour meter, the meter completely accord with relevant technical requirements of class 1 and class 2 single phase energy meter stipulated in National standard GB/T17215-2002 and international standard IEC61036
-
Product
Low Phase Noise Amplifiers
-
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
Product
Ratiometers
-
Our digital measuring bridge offers exceptional accuracy for direct measurement of the transformation ratio and phase error of all types of energy transformers, autotransformers (single-phase and three-phase), as well as CT, PT and CVT measuring transformers.
-
Product
Rack-Mounted Timing Systems
CommSync II Family
-
The CommSync II family of modular systems provide GPS time and frequency outputs to meet your synchronization requirements. All systems include support for multiple input and output modules including 1PPS, IRIG, HAVE QUICK, PTTI, IEEE-1588 PTPv2, low phase noise 1, 5, and 10 MHz sine wave as well as custom outputs.These systems are available with military SAASM MPE-S GB-GRAM, SAASM Force 22E MRU or civilian C/A GPS receivers. Rubidium or OCXO oscillators provide for excellent holdover performance in the event of failure of the reference inputs. In addition, they may be configured as Distribution Time and Frequency (DTF) systems that are synchronized by an external reference. Dual Redundant systems (CommSync II & CommSync II-D) may be configured with two GPS Time & Frequency (GTF) modules and two power supply modules (AC and/or DC power) for redundancy with uninterrupted automatic switchover.
-
Product
Phasemeter
-
Moku:Phasemeter is based on a digital phase-locked loop architecture and can track the phase, frequency and amplitude of two signals from 1 kHz to 200 MHz. Measure phase changes of less than a millidegree with a sensitivity of better than 100 nanocycles/√Hz. Record frequency fluctuations with zero dead time.
-
Product
Transformer Turns Ratio Meter
TTRM 102
-
SCOPE introduces state of the art precision single phase Transformer Turns Ratio Meter (TTRM ) designed for field testing as well as factory testing of power transformers, instrument transformers and distribution transformers of all types. TTRM 102 along with turns ratio, measures ratio deviation, phase angle deviation, magnetizing current and detects tap-position of single phase transformer in charged switchyard condition. The range of AC voltage selection offers high accuracy in measurement.Both the instrument have in-built TFT display with touch screen and thermal printer. The user friendly, simple instrument makes the testing more easy. With the touch keypad it is possible to enter required DUT information.The ratio results are displayed with % error. Internal non-volatile memory gives the provision of storing test results.Further data can be downloaded to PC or copied to memory stick through USB port provided.
-
Product
Turns Ratio Testers
TRT Standard Series
-
When it comes to choosing a transformer turns ratio tester, TRT Standard series offers some of the most advanced instruments with LCD display out in the market. Each model measures transformer excitation current and phase shift performs automatic vector group detection and magnetic balance on three-phase transformers and three-phase autotransformers. Furthermore, they have a built-in true three-phase power source. Because of that, TRT Standard instruments can test transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.The instruments can output test voltages from 1 V AC to 250 V AC, depending on the chosen model. High test voltage of 250 V AC provides more accurate turns ratio testing compared to other turns ratio testers on the market and extremely low test voltage of 1 V AC enables turns ratio verification of current transformers.TRT Standard series consists of:TRT03 Models (TRT03A, TRT03B, TRT03C) – single-phase voltage up to 100 VTRT3x Models (TRT30A, TRT30B, TRT30C, TRT33A, TRT33B, TRT33C) – single and true three-phase voltage up to 100 VTRT63 Models (TRT63A, TRT63B, TRT63C) – single and true three-phase voltage up to 250 VMore about models differences can be found under the downloads tab, in brochures and comparison sheets.A user can create test templates using the DV Win software and store them in the PC’s memory for later use when in the field.TRT Standard series models have a built-in tap changer control unit. Consequently, it enables remote control of an on-load tap changer (OLTC) directly from the tester. In order to make the most out of this feature, the DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions and saving results. This option, especially in combination with test templates, significantly facilitates and shortens the turns ratio testing time.
-
Product
Power Monitor, AC-Powered, Field Adjustable
YMA/YQA
Power Monitor
NAI's YMA and YQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.High and low voltage and frequency limits, and "pick-up" and "drop-out" time delay are field-adjustable using potentiometers. These power monitors are ideally suited for rugged defense and industrial applications.
-
Product
Signal And Spectrum Analyzer
FSVA3000
Spectrum Analyzer
An analysis bandwidth of 400 MHz, an outstanding phase noise of –120 dBc/Hz and a high dynamic range – the R&S®FSVA3000 signal and spectrum analyzer has everything needed to keep up with demanding measurement applications such as 5G NR. With its high measurement speed and easy usability, it is the right instrument for demanding signal analysis tasks both in the lab and on a production line.
-
Product
3 Phase Voltage Extension To Turns Ratio Meter Rack
T-REX R
-
The Raytech three phase voltage system option T-Rex R is an optional system accessory for 3- Phase transformer ratio meter test sets designed by Raytech (i.e. TR-MARK III R). T-Rex R was designed to give Engineers and Test Technicians the ability to test the phase relationships and actual voltage ratios of transformer windings while applying three phase voltage.
-
Product
9GS/s 16Bit 8GS Mem 8CH 8 Markers RF AWG Desktop
P9488D
Waveform Generator
The desktop version of the Proteus arbitrary waveform generator series offers up to 12 channels in a 4U, half 19” dedicated chassis. The compact form size and small footprint save valuable bench space. So for synchronized, phase coherent, multi-channel applications such as quantum physics and radar applications the Proteus arbitrary waveform transceiver is an ideal, space efficient and cost effective solution.
-
Product
Audio Analyzer / Studio Aid
MiniSonic MS10
-
The MiniSonic MS1/MS10 Audio Analyser/Studio Aid is a complete, hand held, two-channel analogue audio test set that measures frequency, frequency response, phase, level, noise, distortion, crosstalk, speed and path latency (delay).As well as being a quality tester it's a precision line-up tool, a stereo PPM, a balanced-unbalanced convertor (both ways),a stereo mic preamp, a headphone amp, and a level convertor.
