-
Product
PXI FPGA & Measurement Accelerator
Measurement Accelerator
Keysight PXI FPGA & measurement accelerator provide digital-pre-distortion (DPD) and envelope tracking (ET) measurements that are embedded in high performance FPGA processing cards.
-
Product
PXIe Measurement Accelerator
M9451A
Measurement Accelerator
The M9451A PXIe Measurement Accelerator combined with Option DPD Digital Pre-Distortion & Envelope Tracking Gateware shows what is possible when you combine state of the art FPGA's with Keysight's trusted measurement expertise and PXIe's high speed data handling. As part of Keysight's RF PA/FEM Characterization & Test, Reference Solution, this combination provides unprecedented performance for demanding envelope tracking and digital pre-distortion measurements required for testing modern power amplifiers (PAs) and front-end modules (FEMs). Hardware acceleration provides better than 20x speed improvement over Keysight's previous host-based Reference Solution, with closed/open loop digital pre-distortion (DPD) and envelope tracking (ET) measurements taking just tens of milliseconds and overall measurement times less than 70 ms.
-
Product
Test & Measurement
-
Quintech Electronics and Communications Inc.
RF Switches for Testing Wireless Solutions.
-
Product
Temperature Measurement
-
HighReach Measuring & Controlling System Co.,Ltd
Describes the process of measuring a current temperature for immediate or later evaluation.
-
Product
Vacuum Measurement
-
Agilent's full range of active and passive vacuum gauges and gauge controllers from atmosphere to UHV/XHV allow you to precisely and reliably control and measure vacuum. We offer Thermocouple (TC), Bayard Alpert (BA), Pirani, Inverted Magnetron (IMG), and Hot Filament (HFIG) gauges. Our gauge controllers are compatible with both Agilent and competitors' gauges and can handle up to 12 channels. Agilent controllers come with several communication interfaces including Profibus, ethernet, and RS-232/485 (other interfaces may be available upon request). There is also the option of a portable gauge controller (HGC-536).
-
Product
Impedance Measurement
CITS880s
-
Finer geometries and thinner copper can present a challenge for fabricators measuring impedance on leading edge PCBs. The CITS880s answers that challenge with the introduction of Launch Point Extrapolation (LPE). LPE extrapolates the TDR response back to a point close to the start of the transmission line effectively allowing to users more accurately to measure the instantaneous or incident impedance of the line.
-
-
Product
Inline Measurement
-
X-Rite's inline solutions increase efficiency, reduce waste, and make life easier for production operators and quality controllers. It's a continuous monitoring system that can catch even small deviations immediately, so changes can be made before production moves out of tolerance. X-Rite offers inline solutions for all stages of paper manufacturing, as well as for the coil coating, plastics, coated glass, textile, and automotive industries. Inline systems are turn-key and have a very quick ROI.
-
Product
Pressure Measurement
-
A range of hydrophones for measuring pressure in ultrasound fields, covering acoustics parameters to meet the latest regulatory requirements needed for IEC62127-1, NEMA UD2 or FDA 510(k) submission.
-
Product
Interface Measurement
-
Interfaces, that is, boundaries between separation layers, can be found everywhere in the process industry, e.g. in the chemical or oil & gas industry. An interface arises when two media with different densities are filled into a container: for example, water and oil. To separate the two media from one another, it is necessary to determine where the transition from one medium to the other is located. VEGA sensors can be used to measure both the total level and the interface reliably.
-
Product
Pressure Measurement
-
HighReach Measuring & Controlling System Co.,Ltd
The measurement of an applied force by a fluid (liquid or gas) on a surface.
-
-
Product
Measurement
Tachometer
-
Tachometer is used for measuring the rotation frequency of shafts in machines and mechanisms, as well as for calculating the number of complete revolutions. Typically, for measuring the rotation frequency, optical or induction rpm sensors are used.
-
Product
3D Measurement
PSD-Array
-
The PSD array consists of 16 parallel one-dimensional PSD elements on the same chip. By utilizing the triangulation technique the reflection of a laser line or multiple laser spots onto the PSD array will provide information about the contour of the illuminated object. The possibility for simultaneous readout of the 16 elements together with the fast response of each element makes the PSD array suitable for applications like high speed 3D contour measurements and measurements of parallel, moving objects such as cantilevers.
-
Product
Testing & Measurement Services
-
Delserro Engineering Solutions
Delserro Engineering Solutions is your complete source forHALT/HASS, Accelerated Life Testing, Environmental Testing, Lead Free Solder Joint Reliability Testing, Linear andNon-Linear FEA, Computational Fluid Dynamics (CFD)
-
Product
Analytical Measurement
-
For over half a century, ABB has developed, manufactured, supplied and installed analytical instruments for the laboratory, process, environmental, steam and power industries.
-
Product
5G Sound Measurement
-
The combination of traditional microphones and modern technology brings portable measurement to a new level.
-
Product
Level Measurement
-
Omega provides contact and non-contact instruments for liquids, and non-contact instruments for solids. Choose from continious measurement or point level measurement with one of our level switches.
-
Product
Measurement System
A0010A RIN
-
realizes world's widest 40 GHz measurement bandwidth with high-sensitivity, low-noise 40 GHz optical receiver and Agilent high-performance X-series signal analyzer. SYCATUS developed unique calibration method, which achieves high accuracy and repeatability.Feature
-
Product
Automated Measurement System
EVG®40NT
-
The EVG40 NT (stand-alone tool) and the AVM (HVM-integrated module) enable measurement of lithography relevant parameters like critical dimension, as well as bond alignment accuracy.Because of the high-measurement accuracy, it is possible to verify compliance to tight process specifications and instantly optimize integrated process parameters.
-
-
Product
Insulation Resistance Measurement
MI15KVe
-
The MI-15KVe High-Voltage insulation tester is a truly portable device that allows the measurement of insulation resistances using test voltages up to 15kV.
-
Product
Gas Measurement Device
Gascoseeker 2-500
-
Teledyne Gas & Flame Detection
Built on the success of the robust and reliable Gascoseeker MK2, the Gascoseeker 2-500 is the UK gas industry standard instrument for measuring % LEL and % volume flammable hydrocarbons, with over 20,000 instruments in use in the UK gas industry.The two-button operation means the Gascoseeker 2-500 is easy to use and operator training can be conducted quickly. The rugged design allows the Gascoseeker 2-500 to be used in harsh environments. The Gascoseeker 2-500 is also fully compatible with our range of calibration software and equipment.
-
Product
Fiber Test & Measurement
-
Thorlabs manufactures a range of devices for testing and measuring the performance of optical fiber. Power, spectral signature, polarization, or end face surface geometry can by characterized with out-of-the-box solutions from our catalog. EO modulators, optical switches, and light sources are available to treat light being used on a test bed.
-
Product
Testing and Measurement
-
AkroMetrix provides a variety of products to help you identify and evaluate warpage: For warpage measurements along a production line or at room temperature, AkroMetrix has developed the LineMoiré Production Level Automated Flatness Inspection System. If you need to measure warpage and flatness during pre-defined temperature profiles, AkroMetrix's TherMoiré In-Process Warpage Measurement Systems may fit your requirements.
-
Product
Surface Quality Measurement System
SQM-500W
-
SQM-500 Surface quality Measurement system is used for the surface cleanness testing and analyze of sample. SQM provide a quantitative analysis of the cleanness of the surface, which was the first announced by us. The system can be used to non-contract detect the contamination of the surface and provide an accurate result immediately. The result can provide a powerful and real data for analyze, which is the insurance for the quality.
-
Product
Rotary Torque Measurement System
-
Honeywell Industrial Automation
Honeywell's analogy telemetry rotary torque systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements.
-
Product
Surface Profiler Measurement System
SP series
-
SP series, high accuracy 3D surface profiler measurement system with white light interferometry.
-
Product
Measurement Software
-
Measurement Software – Comfortable software solutions from MCD allow the user an efficient acquisition and evaluation of specific test data. Especially in the audio and video analysis areas they are most often the cheaper solution to expensive hardware.
-
Product
Non Contact Measurement
-
There is no one-size-fits-all solution for accurate measurement, and different applications require different measurement systems. At Vision Engineering, we design and manufacture a broad range of non-contact measurement systems from toolmakers’ measuring microscopes to fully automated CNC video measuring systems with optional contact measurement available. Combined with the latest metrology software solutions available, we offer the right tool for the job.
