Current Transformer Test
measures insulation, excitation current, turns ratio, winding polarity saturation and/or winding resistance. Current Transformers
See Also: Transformer Test, Transformer Testers, Current Transformer Test Set
-
Product
Epoxy Resin Silicon Rubber Outdoor Voltage Transformer
JDZW-10RG
-
Beijing GFUVE Electronics Co.,Ltd.
Outdoor voltage transformer of the type JDZW-10 is single phase and epoxy resin silicon rubber insulated product, it's used for metering electric energy, voltage control and relay protection in 50/60HZ rated voltage less than 12kV electric system. It can be used for medial voltage AIS, or can be used for medial voltage switchgears. They can operate in all kinds of environments (such as wide range temperature (-50~70℃), high altitude, high humidity, high pollution or salt). This model JDZW-10 outdoor voltage transformer is also as voltage source to supply 220V voltage.
-
Product
Package Testing
-
Lansmont package testing equipment is designed to perform industry standards, such as ASTM, ISTA, ISO, EUMOS and others. Our equipment is compliant with all of the most common ASTM and ISTA package testing procedures. There are individual standards that specifically reference how to perform drop testing, compression testing, side impact testing and vibration testing. In addition to those standards, there are groups of procedures referred to as distribution simulation tests, which incorporate some strategic combination of testing inputs, with the idea of simulating a typical journey through the supply chain. Some of the most common distribution simulation standards that are performed globally are published by ASTM and ISTA.
-
Product
Battery Test
1260
-
*Basic Battery Load Test*Battery Analysis*Mac*Test*Bad Cell Indicators*Testing the Starter Motor*Low Temperatures Effects
-
Product
Test Kit
METRISO 3000
-
Wolfgang Warmbier GmbH & Co. KG
Suitable for resistance point-to-point and resistance to ground measurementsIntegrated data logger with USB communication port for data transmission (50.000 test values). The supplied Report Generating Software ETC allows to generate a complete test reportHumidity and temperature sensorA barcode scanner can be used in order to record measurement points before testing
-
Product
High Current / High Voltage Pulsers
DEI Division
-
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
Product
Wireless Primary Current Recorder Meter
GF2015
-
Beijing GFUVE Electronics Co.,Ltd.
GF2015 is a wireless primary current recorder equipped with a 433M for transmit the recorded data into the user''s PC by our PC-Link Software. It is a good assistant of power monitor system. The recording interval can be set from 1- 60 min. The PC-Link Software can generate reports and create graphs for profile analysis.
-
Product
Qualification Testing
-
Qualification testing is an important step in evaluating how well spacecraft and launch vehicles perform under severe loading conditions that occur during launch and operation. ATA has conducted acoustic and vibration qualification testing of numerous launch vehicles and spacecraft components.
-
Product
In-Circuit Test
-
Test Coach has been delivering the highest quality in-circuit test programs since 1998. Our engineers have the education, experience and expertise needed to solve your most challenging test requirements. We partner with our customers to provide comprehensive test solutions, including consulting on: design for test, recommendations on the best hardware and software options to implement, test strategy, and long term planning for multi board projects. Our expertise allows us to really understand customer requirements, so that quotes are accurate and timely. However, we also understand that sometimes projects can change scope. At Test Coach, we have the flexibility to adapt to changes with as little impact to delivery as possible.
-
Product
Test Handler
-
Test Handler is an equipment that automates the final testing of semiconductor devices. It handles device transportation, controls temperature during semiconductor testing, and sorts devices based on test results.
-
Product
High Current SMU Family 2000 A
AXC76xx
-
Generate very short, fully regulated current pulses from 2 ms to DC with up to 2000 A. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
Product
Automatic Test Equipment, Test Interface Units and Test Program Sets
-
Axis Aerospace & Technologies Ltd.
AXISCADES is a pioneer in Test Solutions and has a long pedigree in developing Test Systems. AXISCADES has designed and developed Automatic Test Equipment, Test Interface Units/Interface Test Adapters and associated Test Program Set Software for Indian and Global, Aerospace and Defence OEMs and End Users.
-
-
Product
Test Companions
-
Test lead kits that include our Test Companion carrying cases for conveniently storing your test accessories.
-
Product
Mini AC Leakage Current Clamp Indicator
MLD-18
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・The LED will blink when detection leakage current exceeds AC 15mA.・Supports ELB with high-speed detection of 20ms.・The operating period is about one month, which is suitable for detecting intermittent leakage current.
-
Product
Meter Testing
METES
-
Meter test systems with high accuracies of up to 0.02% and a wide measuring range for precise measurements in single- and three-phase applications. The meter test systems of the METES series are used to test the accuracy of Ferraris meters and electronic electricity meters under any operating conditions. The impact of system perturbations such as harmonics or flicker on the meter can be taken into consideration during tests.
-
Product
Safety Testing
-
Whitelegg has over 80 years of experience in the design manufacture of market-leading electrical safety test equipment. Our unrivalled range of electrical test equipment serves a wide variety of safety testing and precision measurement applications for use in a variety of industries including manufacturing, construction, education, utilities, aerospace, calibration and anywhere else where there is a requirement for electrical safety testing or precision resistance measurement.Test equipment is cost effective, helps you to minimise expense, improve efficiency and increase profit. Whether you need electrical test equipment, environmental test, power analysers or HV Test Equipment, we stock the products to meet your demands, all backed by our first-class technical support if you have any problems using the equipment.
-
Product
Current Probe
DCFlex
-
Power Electronic Measurments Ltd
The DCflex is an easy to use, low cost, thin and clip-around DC current probe. It is suitable for measuring large DC currents of >2kA. The DCflex takes a single shot measurement of the DC current with a typical accuracy of ±1%. It is important to understand that the DCflex does not provide a continuous measurement of DC current.
-
Product
Magnet Testing
magtrack
-
The magtrack makes it possible to detect the absolute 3D position in space as well as the orientation of a magnetically marked particle over a course of time. The magtrack system is modular and can therefore be adapted to any installation and system.
-
Product
DC Constant Current Source
-
SCR ELEKTRONIKS have developed equipment namely“DC CONSTANT CURRENT SOURCE”. The system comprises of Constant Current Sources having ranges: 900A continues & 3000A short time at 8V maximum.
-
Product
Testing Automation
-
Zhengzhou SMS Electric Co.,Ltd
Three-phase electric energy meter automatic calibration pipeline.
-
Product
Electromagnetic Testing
-
Xiamen IDEA Electronic Technology Co., Ltd.
Is the process of inducing electric currents or magnetic fields or both inside a test object and observing the electromagnetic response.
-
Product
AC/DC Current Probe
CP 30
-
The CP 30 current probe has been designed for use with multimeters respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
Product
Magnetic-Inductive Testing
MAGNATEST® Product Family
-
Foerster Instruments, Incorporated
The MAGNATEST product family is used for the non-destructive testing of metallic materials for magnetic and/or electrical properties. The test instruments are used in the automotive and aviation sectors as well as in the production of semi-finished products. The focus is on testing components relevant to safety such as brake discs, or ball pins and functional components such as camshafts and drive shafts, pivots and piston pins. Typical test tasks include hardness checks, material differentiation and sorting. MAGNATEST can also be used for the automatic testing for the geometric properties of all metallic series components. The high-performance amplifier installed in MAGNATEST test instruments makes it possible to analyze harmonics, which guarantees an extremely reliable and precise repetition, even when impacted by perturbations.
-
Product
AC Leakage Current Tester
229-2
-
Testing for dangerous small leakage currents is easy with the Simpson Model 229-2 Leakage Current Tester. For use in appliance field service, in the lab, or in production, the 229-2 approximates the human threshold of perception in detecting hazardous AC leakage current. The 229-2 comes with test leads with alligator clips, manual and batteries.
-
Product
Color Tests
LED-Check
-
LEDs are the standard light source in car cockpits. It is not sufficient to find out if a LED shines, or not. The LED needs to have precisely the specified brightness and color to fulfil its function.The FiberVision LED-Check system tests up to 250 LEDs in less than one second.
-
Product
Crack Testing
STATOGRAPH® Product Family
-
Foerster Instruments, Incorporated
The STATOGRAPH product family is used for testing surface cracks with the help of eddy current sensors. Eddy current testing for material cracks requires the appropriate evaluation electronics and probes adapted to the testing task. Depending on the test situation and test object, the STATOGRAPH family of test instruments offers the right system for this purpose.
-
Product
Portable Power Source - Power Transformer and Charger Manufacturer
-
JYUE LII INTERNATIONAL CO., LTD.
A&V power transformer supplies and manufactures certified portable power source and charger with industrial UL / cULus / CB / CE / TUV & ISO 9001:14001 certified electrical products and manufacturing facilities based in Taiwan. Portable Power Source Includes C Series, H Series, J Series, L Series, M Series, P Series, Q Series, W Series, Power Bank Series Portable Power Source
-
Product
Test System
DA-1 ATS
-
The DA-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
Auto Transformers
-
Osborne often recommends Auto Transformers in situations where reducing physical size of the transformer is advantageous. Auto transformers offer size advantages when compared to equivalent isolation transformers. Auto transformers provide lower levels of regulation than the equivalent isolation transformer. Osborne helps our clients accommodate for the loss of regulation while achieving the physical size (and cost) advantages of auto transformers.
-
Product
Audio Testing
-
Sound Power testing is required in many international standards. Quest also offers a variety of additional acoustic tests and the design experience to help you develop quieter products for your customers. Our chamber is able to cancel out all outside forces as well with its free floating floor boards.
