Analog Oscilloscopes
Analog oscilloscopes directly apply a voltage being measured to an electron beam moving across the oscilloscope screen, which deflects the beam up and down, tracing the waveform on the screen. (fluffah.phy.uncwil.edu)
See Also: Oscilloscopes, Digital Storage Oscilloscopes, Oscilloscope Probes
-
product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781028-01
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
product
Digital Storage Oscilloscope
DCS-1000B Series
*100MHz/70MHz/50MHz Digital Storage Oscilloscope*Waveform update rate up to 50,000wfms/s*256 color gradient 7inches WVGA display*10M memory depth per channel independently*1M FFT mathematical sampling analysis mode*Zoom In/Play and Pause Function*Diversified Trigger Functions*X-Y Mode Display*Go/NoGo Function*Data Log Function*Digital Filter Function*36 Measurement Parameter Selections
-
product
Sixteen Channel, 12-Bit Analog Input Card
PCI-AI12-16(A)
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
product
Mixed Signal Oscilloscope: 70 MHz, 4 Analog Plus 8 Digital Channels
MSOX2004A
70 MHz4 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
product
PathWave BenchVue USB Modular Oscilloscope Pro
BV0024B
The PathWave BenchVue USB Modular Oscilloscope Pro software configures and controls the oscilloscopes to capture screen images, record and log data.
-
product
Switched Amplifier With Analog Detector Output
Operates at 3 GHz-10 to -5 dBm Input Power to +4 to +7 Output powerAnalog Detector OutputTTL Compatible, 70 dB On-to-Off Ratio, 50 ηSec Response Integrated RF Switch
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Mixed Signal Oscilloscope - 100 MHz, 2 Analog Plus 16 Digital Channels
MSOX3012T
100 MHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
product
Analog to Digital Video Converter/Embedder
SDI Pro VADC-100
The SDI Pro VADC-100 converts composite analog video to SDI video and embeds two channels of analog audio.
-
product
Micsig Smart Oscilloscope
STO1000C/E
Shenzhen Micsig Instruments Co., Ltd.
*Up to 70Mpts memory depth, Zoom into a selected part of the captured waveforms to get more details. *Support serial triggering and decode (I2C, SPI, RS232/UART,CAN, LIN) and Aerospace and defence (MIL-STD 1553, ARINC 429). Two formats to display decoding, text and graphic.
-
product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-01
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
-
product
Simple analog pull tester ROOFIRST
ROOFIRST
Com-Ten's ROOFIRST pull tester is a valuable solution to test fasteners on the roof. It is used to prove the fastening integrity for existing or new roof construction. It is designed to record and document on site pull-out values. It can be used in horizontal or vertical tests in all type of substrates.
-
product
PXIe-5105, 60 MHz, 8-Channel 128 MB, 12-Bit PXI Oscilloscope
783590-02
PXIe, 60 MHz, 8-Channel, 12-Bit PXI Oscilloscope—The PXIe‑5105 high-density PXI oscilloscope has eight simultaneously-sampled channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 60 MS/s or 60 MHz of analog bandwidth. The PXIe‑5105 also features advanced PXI synchronization and data streaming capabilities.
-
product
DMX to Analog Interfaces
The MTX-DE48 decodes signals from DMX control desks to analog dimmers. It is used to integrate DMX controllers into existing analog installations. The standard 0 to 10V output is compatable with many LED drivers. Output may be adjusted up to 28V for use with some older dimmer systems. A negative output voltage option is also available.
-
product
12-bit, 4 Analog Current Outputs With Separate Grounds, Optically Isolated 500 V
APCI-3504-C
4 analog current output channels with 500V optical isolation, 12-bit resolution, each output has its own ground line.
-
product
3GHz RF Analog Signal Generator Module
LS3081D
The LS3081D, 3GHz Single Channel RF Analog Signal Generator, offers industry leading performance, combined with a compact small footprint form factor. The LS3081D features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS3081D was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
product
Front Panel Cover For The InfiniiVision 2000 And 3000 X-Series Oscilloscope
N2747A
Protect your InfiniiVision 2000 or 3000 X-series oscilloscope display and input channels during storage and transport.
-
product
Isolation Amplifier Analog Output
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a high-accuracy D/A converter on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
product
Service Telephone for POTS / Analog Line
1TA701
Test Phone is self-powered, portable telephone test set for use by servicemen that are providing installation, maintenance and repairs of the terminal telecommunication equipment. Test Phone is intended to be used in normal environmental conditions.
-
product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781209-01
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
product
CC0550X, 50 MHz, 5 Arms Current Oscilloscope Probe
786846-01
The CC0550X, or Hioki CT6700, is a clamp-on current probe that offers a wide DC to 50 MHz bandwidth and 5 Arms of continuous input. It is ideal for capturing transient current signals from switching power supplies, inverters, and motor … controllers. The probe requires an external power supply.
-
product
Turbine Flowmeters with Analog Output
CT600R, CT800R Analogue Series
High accuracy turbine flow meters with built-in loading valve and analogue output, for use with hydraulic fluids. Flows up to 800 lpm (210 US gpm).
-
product
Analog Waveform Development and Analysis Software
WaveEasy
WaveEasy is an interactive analog waveform editor software tool for creating and editing analog waveforms. To view or edit existing waveforms, you can open or save files using various file formats including WaveEasy, ASCII or text (txt, csv, prn), or the NI-HWS (hws) format which is used by many instrument drivers.
-
product
Digital Oscilloscope, Digital Oscilloscopes, 2 Channel, 60 MHz, 1 GSPS, 16 Mpts, 5.8 ns
72-7615
Digital storage oscilloscope with 7" TFT LCD display (800 x 480).
-
product
HandyScope HS6-DIFF: 500 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-500XM-W5
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
-
product
Dual Input Digital Handheld Oscilloscope
SDM 760
Dual Input Digital Oscilloscope ; 20MHz. Dual Input Digital Multimeter ; AC/DC Volt, Frequency. Interface ; RS-232 Optically isolated. Operating time ; 2 hours with backlight. Charging time ; 12 hours
-
product
Digital Oscilloscope, 2 Channel, 50 MHz, 1 GSPS, 25 kpts, 7 ns
72-8705A
The 72-8705A from Tenma is a digital storage oscilloscope with 50MHz bandwidth, 2 analogue channels. The digital storage oscilloscope provides trigger modes edge, pulse, and alternate.
-
product
Soft Carrying Case And Front Panel Cover For 2000 And 3000 X-Series Oscilloscope
N6457A
The N6457A Soft carrying case is the perfect way to travel with or store your 2000 or 3000 X-Series oscilloscope. The case is designed for convenience with padded sides and bottom, as well as a storage pouch for your probes and additional accessories.
-
product
RTM Digital & Analog IO Board
*Bus Interface:- 16 Bit Data bus, 8 Bit Address Bus*Spartan-3AN FPGA based design
