Generators
Generation of electrical, mechanical, data, electrical, vapor or gas states.
See Also: Waveform Generators, Frequency Generators, RF Generators
-
product
VXG Vector Signal Generators
Keysight's VXG vector signal generators offer the industry's highest output power with ultra-low phase noise for your most demanding wireless and aerospace and defense applications. With the VXG's multichannel architecture, quickly switch from blocker and interferer tests to MIMO and beamforming tests.
-
product
Standard 1.10 (31.00) - 3.85 (109.00)General Purpose Probe
SPA-64-4
Current Rating (Amps): 3Average Probe Resistance (mOhm): 50Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 375Overall Length (mm): 9.53Overall Length Remark: Exact length depends on selected tip: Tip 1,4, 7: 0,375″; Tip 2,3: 0,365″; Tip 8: 0,385″; Tip ,9,10: 0,363″
-
product
DC Converter
Primary switched DC converter modules are used, among other things, to generate different (consumer) voltage levels from central DC voltages, also battery-supported.
-
product
Capacitance Bridge
TCB-108
Model TCB-108 - Capacitance Bridge is a general purpose bridge for measurement of capacitors, capacitance of transformers and dielectric material. It comprises a transformer-type bridge operating from an internal 108 Hz generator(for accurate measurement at 60Hz) with digital readout of capactiance from 1 pF to 99.999 pF over four ranges and digital readout of D (dissipation factor) in percentage from 0-50%.
-
product
PCI Express 3.0 Test Platform with SMBus Support
The Summit Z3-16 Test Platform with SMBus Support allows the Summit Z3-16 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen3, Gen2 or Gen1 hosts and devices. In addition, it supports the Summit Z3-16 with SMBus Support by providing SMBus tapping connectivity.
-
product
WAFER MVM-SEM
E3300 Family
The E3310 is a WAFER MVM-SEM* for next generation wafers, supporting 1Xnm node process development and volume production at the 22nm node and beyond. With its high-speed carrier system employing a dual arm vacuum robot, and low-vibration platform to improve measurement accuracy, the E3310 delivers high throughput and performance for wafer measurements. Its multi detector configuration and unique 3D measurement algorithm also enable stable, high-accuracy measurement of 3D transistor technologies such as FinFET. The E3310 makes a significant contribution to reducing process development turnaround time and improves productivity for next-generation devices.
-
product
MeasureLINK™ Software
MeasureLINK executes sequences of user-defined experimental steps that can include setting field and temperature levels as well as sourcing and measuring electrical signals. Steps also generate the user interfaces needed to gather inputs before running experiments. You can select steps from MeasureLINK’s editor.
-
product
Digital Circuit Breaker Analyzer
CT-3500 S2
The CT-3500 S2 is Vanguard’s second generation, stand-alone, digital, microprocessor-controlled, circuit-breaker timer. It measures the elapsed time from the instant a breaker coil is energized to the instant of opening or closing of a circuit-breaker’s dry contacts. In addition to timing a breaker’s contact response time, the CT-3500 S2 can also time relays or other switching functions that use an initiating trigger voltage (24-300 Volts DC or AC). The timer-triggering voltage starts three independent electronic timers. Each timer is individually stopped by its respective dry-contact closing or opening. The CT-3500 can fully analyze the timing of all circuit breaker operations (Open, Close, Open – Close, and Close – Open). Timing results are displayed in milli-seconds and cycles on the unit’s back-lit LCD screen and can be printed on the built-in 2.5-inch wide thermal printer.
-
product
Ultra High 6.70 (190.00) - 11.80 (335.00) General Purpose Probe
EPA-4E-2
Current Rating (Amps): 7Average Probe Resistance (mOhm): 35Test Center (mil): 187Test Center (mm): 4.75Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 1,320Overall Length (mm): 33.53
-
product
Standard 1.68 (48.00) - 3.20 (91.00) General Purpose Probe
HPA-52T
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 75Full Travel (mm): 1.91Recommended Travel (mil): 75Recommended Travel (mm): 1.91Mechanical Life (no of cyles): 250,000Overall Length (mil): 629Overall Length (mm): 15.98
-
product
Rotating Construction Lasers
Rugby Series
Work confidently with the Rugby Series General Construction Lasers - self-leveling for jobs of any size, large or small. The Leica Rugby has the features you need to get the job done.
-
product
NI-9220, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Modul
782615-01
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module - The NI‑9220 performs simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. The module is capable of generating 3.2 MB/s of data at … the maximum sampling rate. There are two connector options for the NI‑9220: a 36-position spring-terminal connector and a 37‑position D‑SUB connector.
-
product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 24 Channels
DN6.653-24
The generatorNETBOX DN6.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either up to 48 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
product
Medical Temperature Probes
types include: skin medical temperature probes, general purpose medical probes, esophagael/stethoscope medical temperature probes and foley catheter medical temperature probes.
-
product
Medium-power DC Electronic Load (900W~6000W)
FT6400A Series
Shenzhen FaithTech Technology Co., Ltd.
The FT6400A series has modular design, with strong adaptability, high reliability and high maintainability. Mainly used in power electronics testing fields such as power batteries, medium and high power DC power supplies, DC generators, etc. The FT6400A electronic load not only provides OCP, OVP, OPP, OTP, RVP but also provides Von and Voff functions and programmable protection functions for the device under test. These features can greatly improve the reliability of the product, and it is a reliable product for engineering test and automatic test system integration.
-
product
Deskew Calibration Source for CP030, CP030A, CP031, CP031A, AP015, CP150, CP500
DCS025
The DCS025 Deskew Calibration Source generates time-aligned voltage and current pulses for precise deskew of voltage and current probes.This is critical for measurements in which small propagation delay differences between probes can have a large impact on a calculated measurement, e.g., instantaneous power semiconductor device loss measurements.
-
product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
product
9kHz To 40GHz Signal Generators Module
Corech Microwave’s Ultra Wideband Signal Generators Module operates from 9kHz to 40GHz, featured with ultra wideband, CW/Pulse mode, ultra low noise of -105dBc/Hz@10kHz , low spurious and low consumption. They are very rugged and stable to be integrated in various systems.
-
product
Spectral Analysis
Quality Engineering Associates Inc.
QEA’s PSpec series of products is a new generation of hand-held, wireless, high-performance digital spectrometers that make spectral analysis easier and more convenient than ever before. With our PSpec devices the lab goes with you, enabling collection on the fly of objective, unambiguous data, whenever and wherever it’s needed. Built-in wireless connectivity via Bluetooth enables two-way communication with your smart, tablet or PC. PSpec devices include PC-based Excel application software for data logging, analysis and reporting. With PSpec you’ll enjoy a whole new world of state-of-the-art, mobile analysis tools at an affordable price. The PSpec series offers the perfect tool, whatever your application.
-
product
Directional Source
BAS003
The BAS003 Source is designed to generate homogeneous sound fields using random noise in compliance with the following standards: Building acoustics (insertion loss, acoustic absorption area, etc: ISO 140-3, ASTM E90, ISO 140-5, ASTM E966). The BAS003 is typically used to generate a noise in a free-field for the evaluation of the transmission loss index of a façade. The available high-efficiency power amplifier, BAS002, is light and can be remotely controlled for easy use in the field.
-
product
Universal Partial Discharge Measurement and Analysis System
MPD 800
Our MPD 800 universal partial discharge (PD) measurement and analysis system represents the next generation of our widely-used and innovative MPD PD testing technology. Enhanced and newly-added hardware and software features ensure highly-sensitive multi-channel PD measurements for reliable, industry-standard PD testing on a variety of electrical equipment and components.
-
product
Hand Multipliers
Perfect for service applications, Mountz hand torque multipliers bring power to where your workers need it most. Since they don’t rely on electric, pneumatic, or hydraulic power, hand torque multipliers are great tools for heavy fieldwork. Their small size, light weight, and durable construction make them convenient for field techs to carry, and their strength—up to 36,880 lbf.ft of precisely controlled torque—ensures that your workers can tackle any job. Useful in automotive, heavy machinery, petrochemical, power generation, mining, boring, and shipping, Mountz hand torque multipliers provide maximum capability with minimal investment.
-
product
TrainLink™ End Of Train Device
NG5 ATX
Based on over 30 years of EOT experience, Wabtec's new generation TrainLink™ NG5 ATX has been expertly designed with industry leading communication capabilities featuring a durable external antenna and a lightweight, but rugged construction meant to withstand abuse from railway operations.
-
product
Ethernet Traffic Generators/ Performance Analyzers
Ideal test beds for lab design, troubleshooting and mass production test of network products, supporting 10G/1000M/100M/10M Ethernet.
-
product
Machine Vision System Computer
Neousys Nuvo-7xxx Series
The most popular line for industrial vision systems. A large number of interfaces - for almost any task.- Intel® 9th / 8th Generation Core ™ i 35W / 65W LGA1151 CPU- MezIO ™ interface - Operating range from -25 ° C to 70 ° C based on fanless cooling- GigE ports, support 9.5 KB jumbo frame- M.2 2280 M key socket (Gen3 x4) supporting NVMe SSD or Intel® Optane ™ - USB 3.1 Gen2 and USB 3.1 Gen1 ports - VGA / DVI / DP, support 4K2K resolution
-
product
20 MHZ Arbitrary Waveform Generator
F175 AWG
he F175 AWG does not replace our current square wave generator models (F125/165/170/110). It is an arbitrary waveform generator. Its main strength is in producing non-square waves. Of course it is also able to produce square waves but if you only need generate square waves, please look at our other models: F125/165/170/110. We expect to have F175 AWG production boards available in the third quarter of 2009.
-
product
Universal Clock
DXD-16
The DXD-16 Universal Clock is a PTP Grandmaster clock with GPS receiver and a multi-format legacy reference generator. While working in a PTP environment, the DXD-16 keeps legacy equipment perfectly synchronized with the IP infrastructure, or vice-versa.
-
product
Model Based Testing
RTT-MBT
Verified Systems International GMBH
The RT-Tester Model Based Test Case and Test Data Generator (RTT-MBT) supports model-based testing (MBT), that is, automated generation of test cases, test data, and test procedures from UML/SysML models. Moreover, it generates traceability data relating requirements, test cases, test procedures, and results.
-
product
General Purpose Reaction Dual Shaft Torque Sensor
STS SERIES
The STS Series is our general purpose reaction type shaft torque sensor. They are often installed between devices such as motors, switches, shafts or axles, and their mounting plate to provide bi-directional torque output. They are available in six capacity ranges from 600 in-lb through 12,000 in-lb, and are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Radar Simulation 3.0
RADSIM
RADSIM provides the fidelity and flexibility of a phototexture-based digital radar landmass simulation (DRLMS) system. It uses Leidos-developed core radar simulation technology and can produce a very high-fidelity geo-specific or generic, simulated real-time synthetic aperture radar (SAR), Doppler beam sharpening (DBS), and real beam imagery to less than one-meter resolution.
