Generators
Generation of electrical, mechanical, data, electrical, vapor or gas states.
See Also: Waveform Generators, Frequency Generators, RF Generators
-
Product
Positional Current Probe, PCB Track Touch And Measure
I-prober 520
-
Current measurement from insulated probing of conductorSuitable for observation and measurement of current in PCB tracks, component leads and ground planesWide dynamic range of 10mA to 20A peak to peakWide bandwidth of DC to 5MHzLow noise figure equivalent to <6mA rms at full B/WSafety rated to 300V Cat II (600V Cat 1)Suitable for connection to any oscilloscopeHigh accuracy general purpose H-field probeConverts to 'closed magnetic circuit' current probe
-
Product
High Speed Matrix Card
MATX4001
-
The MATX4001 module is a general purpose-switching matrix, consisting of 40 relays arranged in 5 rows by 8 columns. Each row/column consists of independent Force/Sense lines that are switched simultaneously. Each relay is capable of handling 1 Amp and can isolate up to 5 KV. Each relay on the matrix is independently controlled with an On/Off command via software
-
Product
Single Board Computer
VPX3-1259
-
Curtiss-Wright Defense Solutions
The VPX3-1259 from Curtiss-Wright Defense Solutions is a high performance Single Board Computer (SBC) featuring the 5th Generation Intel Core i7 (Broadwell) processor. Pin-compatible with our previous generations of Intel SBCs, the VPX3-1259 offers the highest performance Intel processing in the smallest 3U form factor.
-
Product
IGBT For Inverter
-
IGBT product series for inverter for UPS, motor control, solar power generation, and welding applications, recommended for 1 to 50 kHz frequencies, and guaranteed against short circuit.
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781340-03
Vector Signal Generator
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
Product
ELECTRONIC MEGOHMMETER
MI-1050e
-
The MI-1050e general purposes megohmmeter is a truly portable equipment suitable to measure insulation resistances using test voltages up to 1 kV. It employs high-reliable, state-of-the-art technology for accurate measurements of ultra high insulation resistances up to 2.000.000 MΩ with four test voltages: 100 V, 250 V, 500 V and 1.000 V.
-
Product
Multi Functional VME Logic Module
MDGG-8
-
The MDGG-8 is a single wide 6U VME multi functional FPGA based delay logic and timing module which provides often needed functions as gate, delay & pulse generator, logic fan in – fan out, coincidence register and scaler / pre-scaler.
-
Product
Box Recorders
-
Generous memory stores 500 event records and over a years worth of summary data. Graphs, charts and summary reports are easily produced using the included ProVision™ software package.
-
Product
Comb Generator
WJ10-100A
-
Comb Generator model WJ10-100A with Broadband Antenna. Frequency Range 10MHz - 11 GHz with two frequencies step size option; 10/100 MHz
-
Product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - 125 MS/s on 4 Channels
DN2.657-04
Arbitrary Waveform Generator
The generatorNETBOX DN2.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either four, eight or 16 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
Product
1553 Avionics Interface 3U CPCI Card
QCP-1553 Series
Interface Card
The QCP-1553 module is a rugged, reliable, full featured, Compact PCI module designed to provide a stand-alone, MIL-STD-1553A/B interface for avionics applications. Up to four independent dual redundant MIL-STD-1553 databus streams are supported by the 3U QCP-1553 module. Additionally, the module offers full functional test, simulation, monitoring and databus analyzer functions for MILSTD-1553A/B applications. An onboard IRIG-B time code decoder and generator allows users to accurately synchronize single or multiple QCP-1553 modules to a common time source. The QCP-1553 module is available in dual or full function (RT simulation, monitoring, and bus controller) configurations.
-
Product
Prototype Measurement Services
-
On-site measurement service for prototype parts using laser tracker for large volume parts or portable arm CMM with optional laser scanning for smaller parts. Point cloud generation and full part modelling is available. API measurement services is an ISO 17025 certified organization, accredited by A2LA, our 3rd party prototype inspection reports provide the necessary confidence demanded by your customers.
-
Product
Pattern Generators
PG311N Series
-
The MicroImage PG311 series of pattern generators are for applications to display custom designed patterns on screen. The PG311 units will overlay the pattern or patterns on top of the video signal provided to the input of the device. The PG311 can be factory programmed with one unique pattern.
-
Product
Benchtop Industrial Ovens
-
Thermal Product Solutions designs and manufactures a complete line of standard and custom Gruenberg industrial benchtop ovens to accommodate a variety of thermal processing applications. Gruenberg industrial benchtop ovens are designed to reach temperatures up to 649°C (1200°F) and are ideal for general lab work, component testing, aging, core hardening, drying, or preheating. With additional options, these industrial benchtop ovens can also be used for applications such as paint baking, plastic curing, varnish baking, sterilizing, rubber and epoxy curing, textile drying, stress relieving, and annealing.
-
Product
Lightning Surge Generator
SKS-0506IB
-
Shanghai Sanki Electronic Industries Co., Ltd.
The lightning surge generator SKS-0506IB1 fully complies with the new standards of IEC61000-4-5, EN61000-4-5 and GB/T17626.5; provides a pulse test voltage of up to 6kV; both AC and DC samples can be tested , subject to The rated voltage of the test equipment can reach 400V, and the rated current of the three-phase equipment is higher than 32A; 7-inch color LCD touch screen, friendly human-computer interaction interface, more intelligent and more user- friendly operation; the software is built in the IEC standard Level mode can be directly called.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors
42-852A-518-M62.5
Multiplexer Module
The 40/42-852A-518-M62.5 is a PXI/PXIe 8-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Standalone Terrestrial Solar Array Photovoltaic Simulator
TerraSAS (ETS Series)
-
AMETEK Programmable Power, Inc.
For microgrids, energy storage, and inverter test applications, the TerraSAS™ series photovoltaic (PV) simulators are specifically designed to emulate the dynamic electrical behavior of a terrestrial PV solar array. They offer low output capacitance and high closed loop bandwidth to keep up with the advanced Maximum Power Point Tracking (MPPT) algorithms used in today’s grid-tied inverters. The Embedded TerraSAS (ETS) is a high performance solution in a small form factor that combines an agile power supply with an innovative I-V curve generator in a single standalone unit.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber, MU Connectors
42-852A-318-M62.5
Multiplexer Module
The 40/42-852A-318-M62.5 is a PXI/PXIe 8-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode
40-855A-122
Multiplexer Module
The 40/42-855A-122 is a PXI/PXIe dual 2-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Compact Multi-use Type Rotary Encoder
RP-432Z
-
Compact and economical design for general purpose;ideal for OEM applications5 VDC or 12 VDC operationEasy-to-use output signal connector2-phase and zero mark square wave outputsNine output pulse types to select from.
-
Product
Clock Drivers
-
Multiple timing signals ("clocks") are required by CCDs, IR FPAs, and some CMOS image sensors to transport electrical charge across the array to a sense amplifier for conversion into image data. Pulse Instruments offers a line of "clock drivers" for generating these timing signals. The parameters of these clocks (clock rate, pulse width, pulse amplitude, rise- and fall-times, etc.) greatly influence the behavior and performance of the imaging device. Our products take logic-level inputs from a pattern generator and allow the user to adjust the output parameters to suit their device and testing requirements. Clocks can be "tweaked" in real-time to determine optimal operating parameters for a particular device, or else programmed in accordance with a test plan for automated production test.
-
Product
PathWave BenchVue USB Modular Function Generator Pro
BV0022B
-
The BenchVue USB function generator pro connects and configures the function generator and links to the Waveform Builder Pro for advanced custom waveforms.
-
Product
Digital ARINC
TA903-02
-
This panel mounted or portable display that reads ARINC 568 distance or ARINC 561 LRN distance. This display employs smart label detection circuitry so that received data must agree with unit strapping. This display is ideal for monitoring distance generated from a GPS, FMS or Dme or a system interface adapter.
-
Product
Software
-
GrayWolf provides state-of-the-art sensor, instrument and software solutions for environmental data logging, survey documentation and report generation. Click here to visit the Customer Self-Serve portal if you are looking to upgrade your existing GrayWolf Software.
-
Product
Radio Communication Tester
CMP200
-
The R&S®CMP200 is an IF tester that combines vector signal analyzer and ARB based generator functionality. The compact integrated solution can be customized with up to three R&S®CMPHEAD30 remote radio heads (RRH), for up/downconverting signals to 5G FR2 frequencies.
-
Product
Test Compliance
CTS Series 3.2
-
AMETEK Programmable Power, Inc.
The CTS Series is a complete, turn-key compliance test system for EN IEC 1000-3-2 (Harmonics) Including A14, EN IEC 1000-3-3 (Flicker) and various EN IEC 1000-4 AC immunity tests. Consisting of an AC power source, a power analysis conditioning system (PACS) and a PC based data acquisition system, the CTS provides a complete turn-key solution for IEC testing. The Windows™ based CTS software performs the IEC tests and generates detailed test reports. Comprehensive data files are stored on disk to allow post test analysis.
-
Product
Complete Network Monitoring
TiSCADA
-
After years of advanced Research, laboratory and on-field tests, Techimp has developed powerful and effective tools which can help asset managers to take critical decisions and manage power plants in a cost saving ways. Ti-SCADA implements a Real Time condition control of your asset, through a powerful Human Machine Interface (HMI) fully configurable, web based, displaying graphs, charts, trends, KPI, historical data, alarms and customizable reports. Ti-SCADA is a fundamental component of the new generation of Techimp on line condition monitoring systems. Ti-SCADA is designed as a Service Oriented Architecture (SOA) based on interoperability standard for industrial automation - OPC-UA - allowing high performance asset management solutions, tailored on customer needs, to be implemented.
-
Product
PXIe-5785, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785584-01
FlexRIO IF Transceiver
12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver—The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors, With Interlock
42-850A-514-M62.5-HI
Multiplexer Module
The 40/42-850A-514-M62.5-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Arbitrary Waveform Generator Software
SourceXpress
-
PC-based software for arbitrary waveform generator control & emulation. From your PC, create waveforms using tools specifically targeted for your needs. From your PC, control one or many source instruments such as the AWG70000s. Control one or several AWG70000 instruments from one application. Load and play waveforms remotely. There is no new application to learn! SourceXpress™ has the same look and feel as the AWG70000 instruments.
