Reactive Load Banks
Provide both lagging and leading power factor loads.
See Also: Load Banks, AC Load Banks, DC Load Banks, Inductive Load Banks, Resistive Load Banks
-
Product
Electric Servo Motor Type High Speed, High Load, Large Displacement Vibration Tester
-
This tester is a high-speed, high-acceleration vibration tester equipped with an electric servomotor actuator.
-
Product
Axle Load Simulators
-
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
Product
PXI 1 Bank of 160 Channel 1 Pole MUX
40-615-022-1/160/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
DC Electronic Load Modules For The N6700 Power System
-
Test devices that store or convert energy by adding a DC electronic load to your Keysight N6700 Series power supply. The Keysight N6790 Series electronic load modules can perform a static or dynamic test and are available in two sizes: single-wide 100 W and double-wide 200 W modules.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-33S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 1A～200A*Current measurements of feeder
-
Product
Power Supplies And Loads
Power Supply
Power Supplies and Loads power devices under test (DUTs) such as RF power amplifiers and cellular handsets. The power supply takes in AC power and delivers DC voltage with a fixed polarity, either positive or negative, to its load.
-
Product
LXI Single Bank, 12:1 MUX 75 Ohm 1GHz F-type
60-722-001
Multiplexer Module
Our 60-722 High Isolation RF Multiplexer is suitable for switching 75Ω signals up to 1GHz. With the choice of single or dual multiplexer banks each with 12 channels, it is ideal for constructing complex microwave switching systems for many applications.
-
Product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
-
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
Product
48V / 200 Amp Load
EL12-48M
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely costeffective.
-
Product
110V / 100 Amp Load
BD12-110P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Auto Load 4 Moving Probe Tester
AL Series F4H4033AL
-
Medium and High Volume Production Model with Auto Loader. Max. Test Area 15.7 x 13" (400x330mm). Max. Transferable Panel Size 16.5 x 13.4" (420x340mm). Number of Probes 2 Upper, 2 Under. in. Pad Pitch *4 0.00236" (60µm). Min. Pad Size *5 0.00118" (30µm).
-
Product
500 AMP Carbon Pile Load Tester
CP710
-
Tests batteries rated as high as 1000 CCA or 160 amp hour. Also tests alternators, regulators, and starters
-
Product
Loading Adjustable Drop Tester Machine
CX-DL15A
-
Shenzhen Chuangxin Instruments Co., Ltd.
Package Impact Drop Testing Machine is used to measure the dropping impact incidence when the package in using, transportation and decorating. Labtone "1G+" project strictly ensure the accuracy. Besides precision plane drop testing, it also can undertake edge and angle test to ensure the complete performance evaluation for the package. During the products handling or transport process, there may be drop/ fall, which results in damage within the products. And this Drop Tester simulates the drop/ fall of a finished product to evaluate the damage. All the rhombohedrons, angles and faces of the products can be tested.
-
Product
High Power DC Electronic Load
34000C Series（6KW~24KW）
-
34000C Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.
-
Product
Acoustic Load Shackle
ALS-2.0
-
The Acoustic Load Shackle is designed for subsea operations where load monitoring is required, either for short term operations lowering an item to the seabed or for longer periods monitoring dynamic loads.
-
Product
Bolt Extensometers for Proof Load Testing
Model 3565
-
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Programmable LED DC Electronic Load
M98 Series
-
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
Product
Water Cooled Active Resistance DC Electronic Load
WRx Series
-
Utilizing Magna-Power’s new patent pending Active Resistance Technology in combination with the company’s internally manufactured microchannel water-cooled heatsinks, the WRx Series addresses high power DC applications where exhaust heat control is essential. The WRx Series greatly increases power density compared air-cooled alternatives. An integrated solenoid controls the flow of water to avoid condensation. Full power can be achieved using conventional water, with water inlet temperatures up to 25 °C.
-
Product
Combined Load Banks
C-Series
-
C-series combined load banks are devices which contain resistive and reactive loads, apply the load to an electrical power source and dissipate the power of the electrical power.
-
Product
High Precision Electronic Load
PEL-8000
-
PEL-8000 series adopts high-performance chip high-speed and high-precision design, providing resolution of 0.1mV, 0.01mA (basic accuracy is 0.03%, basic current rise rate is 2.5A / US)
-
Product
PXI Solid State MUX, 20 bank, 8 channel
40-680-001
Multiplexer Module
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
Thermocouple, Insert, ITA, SIM, 8 Pos, 3 Slot (not loaded)
510181111
SIM Insert
Thermocouple, Insert, ITA, SIM, 8 Pos, 3 Slot (not loaded)Compatible with 410130116, ITA, i2 MX, 22 Slot VTAC/SIM Insert, EMI, and XL version 410130133Not loaded. Thermocouple patchcords need to be purchased separately.
-
Product
Load Test Software
TW-3.0
-
The TW-3.0 Load Test software from DLM is a software platform designed to complementDLM’s TW-3.0 range of products within the lifting industry. Used as a tool for assisting therecording of test results and generation of certificates during a load test, the software is able to be loaded onto a Windows PC and accept the output from a TW-3.0 handheld display.
-
Product
DC Electronic Loads
LSG Series
-
*Operating Mode : C.V/C.C/C.R/C.P/C.C +C.V/C.R + C.V/C.P. + C.C.*High Precision, High Resolution (10 A),High Speed Variable Slew Rate (16A/ s).*Sequence Function for High Efficient Load Simulations.*Parallel Connection of Inputs for Higher Capacity. (With 4 Booster Units : Max 9.45kW or 4 Master Units)*External Channel Control/Monitoring via Analog Control Connector.*Program Mode to Create Work Routines for Repetitive Tests.*Multiple-Interface : USB 2.0 Device/Host and GPIB/RS-232C.*Adjustable OPP/OCP/OVP Setting.
-
Product
Digital Battery Load Tester
DBT125
-
Battery load test. Depending on the size of the battery, this product adds a very high load to the battery (125 A). It enables the reading of battery condition by voltages and by its ability to maintain the load, thus determining levels of sulphation.
-
Product
VME / VME64x Load Board 6U
1940000140-0000
-
The Elma Electronic VME / VME64x load board provides a means to test the power generated by and cooling capability of VME systems. This makes it easier to locate hot spots in the chassis, so the airflow can be properly directed.
-
Product
600 Watt DC Electronic Load Mainframe
N3301A
Mainframe
The Keysight N3301A is a half-rack width mainframe with 2-slots that accepts combinations of N330x user-installable load modules (150 W to 600 W) for easy system configuration and future reconfiguration. The N3301A holds up to two N3302A, N3303A, N3304A, and N3307A load modules, or one N3305A and N3306A load modules, allowing up to 600 watts of total maximum power.
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SL
-
*Linear laboratory power supply*Integrated electronic load*Linear regulated DC laboratory power supply*No thyristor pre-regulation, very little ripple*Various interfaces · Built-in electronic load*Protection against short circuit, overload and overtemperature*Constant current and constant voltage*Fast control times approx. 250 µS
-
Product
Load Pin Products
-
DLM are world renowned for the design and manufacture of custom design load pins for a host of industries, including offshore moorings, renewable energy and marine & subsea applications.
