Reactive Load Banks
Provide both lagging and leading power factor loads.
See Also: Load Banks, AC Load Banks, DC Load Banks, Inductive Load Banks, Resistive Load Banks
-
Product
Automation Software For Aim-TTi Power Products Including LD And LDH Series Electronic Loads.
Test Bridge
-
Test Bridge software is a simple Windows application intended to make it possible to create a test sequence that can control up to four Aim-TTi products and record measurement results in graphical and tabular form.
-
Product
48V / 200 Amp Load
BD12-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
PXI MUX 2 Bank, 32 Channel Screened 1 Pole
40-610-021-S-2/32/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
On Load Tap Changer Analyzer
TAP-4-PLUS
-
The Tap-4-PLUS is the newest instrument by Zensol for OLTC testing. It has 2 more analog inputs than the TAP-4. The TAP-4-PLUS with the TAP-DRM accessory can perform dynamic resistance, vibration, and motor current recordings at the same time. Doing so will allow you to easily understand the vibration impacts.
-
Product
Refrigerator Freezing Tester M Load Test Package
CX-MP
-
Shenzhen Chuangxin Instruments Co., Ltd.
The freezing load test package is made according to GB/T8059.2 GB/T8059.4, and we can also make the package in different standard according to different requirement.
-
-
Product
Programmable DC Electronic Load - (Economical)
63200E Series
-
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
Product
PXI 10 Banks of 16 Channel 1 Pole MUX
40-615-022-10/16/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
Battery Load Tester
MD4260
-
Test capabilities: Battery voltage, battery cranking, battery charging volts and good/bad battery test. Test batteries on and off the car in just 30 seconds. Heavy duty copper-plated clamps. Internal loaded unit with a 100-amp load capacity. Load safety switch to prevent arcing. For 6- and 12-volt batteries.
-
Product
Electric Servo Motor Type High Speed, High Load, Large Displacement Vibration Tester
-
This tester is a high-speed, high-acceleration vibration tester equipped with an electric servomotor actuator.
-
Product
Load Cells and Sensors
-
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.
-
Product
Load Board
cPCI 6U
Load Module
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
Product
Battery Loading Unit
BLUe
-
BLUe series Battery Loading Units; portable instruments for controlled & monitored discharge of batteries. It is designed for integrated site discharge test, design & QC test and also for monitoring discharge process of battery bank with connected load. Single autonomous unit having inbuilt display, keypad and wireless communication with PC makes it very easy to use. It comes in different configurations ranging from 12V to 380V discharge voltages and 50A to 300A discharge currents. Various options are available to control & monitor the discharge process. With the help of optional Cell Monitoring Unit - CELLMon, voltage of each individual cell can be monitored & data sent to main BLUe unit and then from main unit to PC via wireless communication. Each BLUe unit is supplied with PC downloading & analysis software for real time monitoring of discharge process.
-
Product
PXI 4 Banks of 16 Chan 1 Pole MUX
40-657-001-4/16/1
Multiplexer Module
40-657 High Density Power Multiplexer Modules are available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Product
Programmable LED DC Electronic Load
M98 Series
-
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
-
Product
Multifunctional DC Electronic Load (CC/CV/CR/CP)
PLZ-5W/5WZ Series
-
The PLZ-5W Series high performance electronic load is the successor to the highly respected PLZ-4W series, whilst still retaining the same high specification and build quality. Advances include a high visibility color display, low voltage operation from a minimum of 1 V to a maximum of 150 V. Programmable profiles of voltage/current can be applied (using the new ARB function, as used in LED/solar testing) in addition to the inherited 6 modes of operation: Constant Current, Constant Resistance, Constant Voltage, Constant Power, Constant Current + Constant Voltage, Constant Resistance + Constant Voltage.
-
Product
High Slew-Rate High Power DC Electronic Load （100A/μS）
34110A-11（10KW）
-
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.
-
Product
500 AMP Carbon Pile Load Tester
710
-
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
Product
High Precision Canister Load Cell
Model 2000 Series
-
The Model 2000 Series High Precision Canister Load Cell was designed to accurately and precisely measure force, which many other quantities such as torque, thrust, and pressure are based, for aerospace applications. The Model 2000 Series, available with load measurement capacities up to 750K lbf, offers high performance and linearity and very low hysteresis. ±0.02% FS Hysteresis
-
Product
2 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 2 Ports
GPS212
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Electronic Load Device
786529-01
-
The RMX-4003 provides capabilities for qualifying power designs and validating power supply functionality in a production environment. You can combine Electronic Load Devices to customize your test system based on the number of channels, maximum load power, and voltage and current of each channel.
-
Product
3U VPX Conduction Cooled Load Board
1940000446-0000R
-
3U VPX Load Board, conduction cooled.
-
Product
Pedal Force Load Cells
-
Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.
-
Product
8 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 8 Ports
GPS802
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
Precision Gram Load Cell Universal/ Tension or Compression
GSO SERIES
-
The GS0 Series Load Cells can be utilized in tension or compression or both with excellent compliance. The force sensing end of the anodized aluminum GS0 Series is tapped 6-32 thru for attachment possibilities for almost any application. Bonded foil strain gages at the sensing element provide for excellent stability over the suggested temperature range and ensure long term reliability. Call for application assistance.
-
Product
AC Load Banks
X100L-600 Series
-
Mosebach Manufacturing Company
Mosebach’s X100L-600 is the smallest load bank of 100 kW with 5 kW resolution. Offers a continuous load at 600/480/240/208 volts. Great for most generator testing. And lightweight – only 64 lbs!
-
Product
Fully Automatic Full Load (Routine) Testing Panel For Induction Motor
-
Aarohi Embedded Systems Pvt. Ltd
Aarohi introduced fully automatic routine testing panel. The primary purpose of the routine test is to insure freedom from electrical and mechanical defects, and to demonstrate by means of key tests the similarity of the motor to a “standard” motor of the same design. this panel also help to enhance productivity, Work efficiency & reduces need for skill operator. More then 500 Indian pump manufacturer ware installed this system & satisfied with performance.
-
Product
150~300W DC Electronic Loads
JT631 Series
-
Nanjing Jartul Electronic Co., Ltd
JT631 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT631 series load very suitable for testing power supply when produced in large quantity. Besides, JT631 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT631 series load satisfing most of R&D requirements. Moreover, JT631 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
Product
Hand-Held 12 Volt Combo Digital Load Tester
6028DL
-
• 60 Amp load to test smaller batteries: CCA and Amp hours• 125 Amp load to fully test larger batteries: CCA and Amp hours• 125 Amp clamps offer greater flexibility when attaching the hard to reach applications • Made in USA of US and Global Components
