Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
Product
Jaguar Oxygen Sensor
KS60113 - Jaguar
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
PXI Dual 8 to 1 RF Multiplexer 3GHz 50 Ohm SMB
40-874-002
-
The 40-874-002 is a 50 Ohm 8 to 1 RF multiplexer with 2 banks in a single PXI slot. It has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of this RF multiplexer has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXIe-57857, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785586-01
-
The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
Wind-Noise Reduction System
WNRS
-
The Wind-Noise Reduction System (WNRS) is an array of air inlets connected with pipes to reduce wind-noise and improve signal quality.
-
Product
Signal Generator Extension Modules
SGX
-
Virginia Diodes, Inc. (VDI) Signal Generator Extension (SGX) modules provide high performance frequency extension of microwave signal generators into the THz range. VDI SGX modules offer full waveguide band coverage and are available from WR15 (50 to 75 GHz) to WR1.0 (750 to 1100 GHz) with additional bands under development. This turn-key, sweepable solution is compatible with any microwave signal generator that meets the input frequency and power requirements.
-
Product
NIST Calibration for D600A-AT.
D600A-AT-CCNIST
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Gold Probes
4900 Series
-
The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.
-
Product
Diesel Engine Tachometer
GE-1400
-
Handheld type digital engine tachometer to be designed for dedicated r/min measurement of 4-cycle diesel engines. R/min direct reading measurement is available only by clamping a CP-044 Diesel Engine Rotation Sensor (sold separately) to a fuel injection pipe.Both analog (switchable between analog and monitor output) and pulse outputs are provided; enabling to use analog output for data recording (monitor output for sensor waveform checking or analysis input signal of FFT analyzer), and to use pulse output for tracking analysis signal of FFT analyzer.
-
Product
LXI Microwave Multiplexer, SP6T, 4-Bank, 18GHz, 50Ω, SMA
60-800-104
-
Our 60-800-104 is a 4 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
USB-8506, 1-Port, USB LIN Interface Device
784663-01
-
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Low-Pass Filters
-
Low-Pass Filters from Analog Devices are specifically designed to reject higher frequency noise and unwanted signals while allowing desired signals to pass through. Analog Devices offers an extensive line of continuous time and clock tunable (switched capacitor) devices preconfigured for low-pass filtering. These integrated low pass filters feature a wide range of cutoff frequencies and response characteristics.
-
Product
T3DSO Passive Probe, 350 MHz, 1X/10X, 1 MOhm/10 MOhm, 300V/600V
T3PP350
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
Product
PXI/PXIe RF Multiplexer, Dual 8-Channel, 3GHz, 75Ω, MCX
40-834A-102
-
The 40-834A-102 (PXI) and 42-834A-102 (PXIe) are 75 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-834A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
High-Speed Digitizers / Oscilloscopes
-
GaGe high-performance digitizers are renowned for sustaining the maximum effective number of bits (ENOB) over a wide signal frequency range with quality signal conditioning and signal fidelity features. With A/D sampling rates up to 6 GS/s and very deep onboard acquisition memory of up to 16 GB, our high speed PCIe and PXIe digitizers provide optimal combinations of high sampling speeds with 8-bit, 12-bit, 14-bit, and 16-bit high resolution rates with large sampling memory options and high-speed data streaming capabilities.
-
Product
Signal Generator, 20MHz, 1 Channel, Arb.
33511B
-
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated, 3GHz, 50Ω, MCX
40-873A-101
-
The 40-873A-101 (PXI) and 42-873A-101 (PXIe) are 4 to 1 RF MUX with 1 bank in a single slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
Product
USB to RS-422/RS-485 Converter
ND-6530
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
PXIe-2748, 3 GHz, 16x1 PXI RF Multiplexer Switch Module
780587-48
-
PXIe, 3 GHz, 16x1 PXI RF Multiplexer Switch Module—The PXIe‑2748 is a PXI RF multiplexer switch module that is ideal for switching RF signals up to 3 GHz in production test applications. The high channel count of the PXIe‑2748 makes it well-suited for test systems that require switching a large number of RF signals, such as switching several devices under test to a single channel on the RF analyzer. It also features onboard relay counting for relay monitoring.
-
Product
Network Emulators
-
Rohde & Schwarz offers class-leading signaling testers. We established our position as leading supplier of LTE communications testers with the popular, all-in-one R&S®CMW500 platform. Now we are building on the expertise that enabled its success with the high-performance R&S®CMX500 radio communication tester.Secure the industry-leading wireless network emulators for your 5G NR and legacy technology challenges – from R&D design stages up to end-to-end application testing, production and conformance tests.
-
Product
Timing Controller
MS 2009
-
MS5128 Timing Controller has programmable logic generation, Input Output Signals Interface, Timings, macro-cells, Pins, internal timing delay and Signal Levels for airborne microprocessor boards.
-
Product
Coaxial Power Detector
-
RF Lambda’s coaxial power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
-
Product
Microprocessor Development System
DS-M8
-
# Real-Time and Transparent In-Circuit Emulator# Supports PIC12xxx, PIC14xxx, PIC16xxx, PIC17xxx and others# Uses Microchip Bond-Out Technology# Maximum Frequency Support# Standard 64Kx16 Emulation Memory# 32Kx48 Real-time Trace with Filters and Triggers# 64K Hardware Breakpoints with External Signals# Memory Mapping Capabilities# Software for MS-Windows# Source-Level Debugger for C and Assembler
-
Product
PXI High Density MUX 47-Channel 2-Pole
40-640-022-47/2
-
This series of high density multiplexer modules feature a choice of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The multiplexer module is available as a 47-channel 2-pole, 94-channel 1-pole or 47-channel 1-pole with screened relays. Connections are made via a front panel 96-pin connector. It may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available for this 1-pole version).
-
Product
Signal, Patchcord, ITA, 36", TriPaddle, 24 AWG Twisted Pair White/Black, Single Ended (3 Amps)
7-103424000-036
-
Signal, Patchcord, ITA, 36", TriPaddle, 24 AWG Twisted Pair White/Black, Single Ended (3 Amps).
-
Product
PXIe-5451, 145 MHz, 16-Bit, 512 MB, PXI Waveform Generator
781204-02
-
PXIe, 145 MHz, 16-Bit, 512 MB, PXI Waveform Generator—The PXIe‑5451 is a 145 MHz, dual‐channel arbitrary waveform generator capable of generating user-definied waveforms, standard functions, and I/Q communications signals. It is an ideal instrument for including in systems for testing devices with I/Q inputs, or as the baseband component of an RF vector signal generator as wells as time-domain signals like envelope tracking. The PXIe‑5451 also features onboard signal processing (OSP) functions that include pulse shaping and interpolation filters, gain and offset control, and a numerically controlled oscillator (NCO) for frequency shifting. The PXIe‑5451 also features advanced synchronization and data streaming capabilities.
-
Product
Clock And Trigger Synchronization System
CLKSYNC-50
-
CLKSYNC-50 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
Product
Pulse Pattern Generator, 3.35 GHz, dual-channel
81134A
-
When timing and performance requirements are critical, for example in high-speed serial bus applications like PCI Express or Serial ATA, its fast rise times and low intrinsic jitter allow the precise and in-depth characterization of devices, e.g. receivers or backplanes. On top of that, it allows to generate application-specific signal levels like pre- and de-emphasis (PCI Express) or squelch (Serial ATA). The Keysight 81134A lets you test your DUT instead of the pulse or data source!
-
Product
LXI Microwave Multiplexer, SP6T, 16-Bank, 67GHz, 50Ω, SMA-1.85
60-800-816
-
Our 60-800-816 is a 16 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Transmitters
-
A set of equipment used to generate and transmit electromagnetic waves carrying messages or signals, especially those of radio or television.
