Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
Product
TimerBlox
-
Analog Devices TimerBlox parts are small, accurate, and simple timing devices designed for six basic operations: voltage controlled oscillation (VCO), low frequency clocking, pulse-width modulation (PWM), one-shot generation and signal delay, and power-on reset (POR). TimerBlox devices combine an accurate programmable oscillator with precision circuitry and logic. No capacitors, no crystals, no microcontroller, and no programming are required. A 20 mA source and sink capability enables the devices to directly drive opto-isolators and transformers for electrical isolation. An ideal solution for space-limited applications, each TimerBlox device can be placed at the point of use.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 1.25 GS/s, 500 MHz Bandwidth
DN2.221-04
-
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
SHC68-C68-D4, 68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - 1m
196275-01
-
The SHC68-C68-D4, 1m, Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
PXI Power & Sense Multiplexer, 2-Pole, 18-Channel
40-658A-002
-
The 40-658-002 is a PXI multiplexer combining a 2-pole 18-way power distribution MUX with a second lower power 2-pole 18-way MUX in a convenient single slot PXI module. It is ideal for power distribution where power and sense signals are required to be connected to an array of devices under test.
-
Product
PCI 2 Amp Multiplexer, Single 8-Channel, 8-Pole
50-635A-004
-
The 50-635A-004 is a single 8-channel, 8-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI Very High Density Multiplexer, 49-Channel, 4-pole
40-670C-022-49/4
-
The 40-670C-022-49/4 is a 49-channel, 4-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
16 Relay Output PCIe Board, 8 Isolated Digital Input Channels, 24V
APCIE-2200-16-8
-
8 electromechanical relays with change-over contacts The PCI-Express 16 relay board APCIe-2200-16-8 has 16 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
Product
Data Acquisition Systems
-
m+p Coda is a full-featured turnkey software platform for data acquisition, signal analysis and monitoring. Complete turnkey operation provides quicker time to test by eliminating costly application programming and long learning curves. The extensive built-in features and tools offer a functionality that was previously available only in custom packages. The intuitive graphical user interface facilitates set-up, operation and analysis, thus leading to precise, repeatable results quickly.
-
Product
Low Noise Amplifier
-
The COMM-connect Low Noise Amplifier can be used to amplify signals in a wide range of bands. The amplifier comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated, 8GHz, 50Ω, SMA
40-882B-001
-
The 40-882B-001 (PXI) and 42-882B-001 (PXIe) are single 50Ω 4 to 1 RF multiplexers with 8GHz bandwidth. The 40/42-882B range has automatic termination of unused signals and is available as a single MUX in one slot, a dual MUX in two slots, or triple and quad MUXs in three slots.
-
Product
Phase Angle Voltmeters
-
Since the development of the first Phase Angle Voltmeter (PAV) over 50 years ago, North Atlantic Industries has been the industry leader in AC Measurement Instrumentation. Our name has become synonymous with innovation and quality. Our products, specifically designed for defense, industrial, and commercial applications, deliver industry-leading accuracy, repeatability, and reliability.NAI’s units of today are actually multifunction Digital Analyzing Voltmeters that combine a complete Voltmeter, a Phase Angle Voltmeter, and a Waveform Signal Analyzer in a single microprocessor-based instrument. With these versatile and flexible instruments, a wide range of tests can be performed, either manually using the front panel controls or automatically using the IEEE-488 bus. Designed for the Synchro/Resolver and LVDT/RVDT marketplace, NAI’s Voltmeters are used in a variety of applications.
-
Product
PMC SpaceWire
-
PMC SpaceWire implements SpaceWire in a convenient PMC format. With PMC you can install the adapter into PCI [PCIBPMC], cPCI [cPCI2PMC], or processor board pmc slots. The SpaceWire specification calls for LVDS signaling and a specific 9 pin micro-D connector. You can connect the PMC-SpaceWire to other SpaceWire compliant devices without electrical interface issues
-
Product
GHz Elastomer Sockets
-
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
Product
PXI Single 55x8 Matrix 1-Pole Switching
40-538-021
-
The 40-538 ultra high density matrix module is configured as a Single 55x8 reed relay matrix with 1-pole switching. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering >10e8 operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
RF Peak Power Sensors
-
These sensors feature real-time processing and hardware triggering with advanced PC software to capture even the most elusive signals. Measure pulsed, bursted, and modulated signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), consumer electronics (WLAN and WiFi 6), as well as education and research applications.
-
Product
High Power Programmable AC Source
61610
-
Chroma Systems Solutions, Inc.
Power Rating:61511/61611: 12KVA61512/61612: 18KVAVoltage Range: 0-150V/0-300V / AutoConfigurations with input voltage of 220V or 480VFrequency: DC, 15Hz-1500HzSingle-phase or three-phase output selectableProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage and current limitHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetCapable of delivering power output up to 90KVA by implementing Master-slave parallel operation
-
Product
VLF Electromagnetics
-
VLF surveying relies on radio signals that are broadcast from navigation stations around the world. The principle is that these signals are deflected in certain ways when they pass through conductive ore or water-filled vertical-to-sub-vertial fractures in the earth. By monitoring these deflections, the position and, potentially, size of the target can be determined.
-
Product
Twelve-Channel Cable/Terrestrial Receiver for PCIe
DTA-2139C
-
Twelve (!) receivers on one card, supporting a mix of terrestrial (ATSC 3.0, ATSC 1.0, DVB-T/T2, ISDB-T) and cable (DVB-C/C2, ITU J.83) signals. All twelve channels are demodulated simultaneously, allowing you to monitor a complete network in real time.
-
Product
General Purpose Pressure Transducer and Transmitter
P55
-
The robust P55 pressure transducer provides cost-effective reliability for severe test environments. With extreme resistance to shock and vibration, the P55 pressure transducer delivers the same high-level performance expected from more delicate differential pressure transducers and pressure transmitters. With variable reluctance sensing technology, the P55 pressure transducer delivers fast dynamic response, high resistance to vibration and superior signal stability through ambient temperature change for a wide variety of low-pressure to high-pressure measurements. The P55 pressure transducer will accept both liquids and gases directly at the sensing diaphragm and there are no internal isolation fluids to slow the sensor response or cause excessive temperature drift errors.
-
Product
PCI 2 Amp Multiplexer, Single 4-Channel, 8-Pole
50-635A-104
-
The 50-635A-104 is a single 4-channel, 8-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
1149.6 Boundary Scan Feature, GTE 10.00p
K8213B
-
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
Product
PXI-2798, 40 GHz, Dual-Transfer PXI Transfer Switch Module
782358-01
-
40 GHz, Dual-Transfer PXI Transfer Switch Module—The PXI‑2798 can route RF or microwave signals in automated test applications. Designed to operate with less than 1 dB insertion loss at up to 40 GHz, the PXI‑2798 appears almost invisible to signals at much lower frequencies as well. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2798 is also well-suited for passing high-order harmonics from RF upconverters or routing multiple sources to RF downconverters.
-
Product
LXI Microwave Multiplexer, SP4T, 14-Bank, 67GHz, 50Ω, SMA-1.85
60-803-814
-
Our 60-803-814 is a 14 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781421-11
-
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Electrical Power Transducers
-
Manufactured for utilities since 1969, TransData Power Transducers are used for measuring AC and DC power variables in Substation, Generation, Load Control and Industrial applications where ±1ma or 4-20mA analog signal are required by the SCADA/Energy Management System. Models are available for measuring Current, AC Voltage, DC Battery Voltage, Watts, VARs, Frequency and more.
-
Product
RF Signal Strength Meter
006
-
Hand Held RF Signal Strength Meter. Detects RF Activity around centre frequency. Available for 315MHz, 433MHz, 868MHz, 869.85MHz, 914.5MHz.
-
Product
PXI 2A Multiplexer, 1-Bank, 8-Channel 16-Pole
40-614-019
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
Oscilloscope - 100 MHz, 4 Analog Channels
DSOX3014T
-
100 MHz4 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
PXI Dual 2x2 RF Matrix 2.5GHz 50 SMB
40-877-002
-
The 40-877-002 is a 50Ω 2x2 RF matrix with 2 banks in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40-877 modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
Jaguar Oxygen Sensor
KS60113 - Jaguar
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
