Short Testers
Detect unintended circuit connectivity and insulation defects.
-
product
Electrical Testers
Regardless of what your trade requires, Klein Tools has an electrical tester for the job. With non-contact testers as well as outlet and receptacle testers, there’s guaranteed to be the tool for your jobsite needs. All Klein’s testers are engineered for ease of use and to stand up to the tough jobsite conditions encountered by professionals every day.
-
product
SMARC Short Size Module with Rockchip PX30 Quad-Core ARM Cortex A35
LEC-PX30
LEC-PX30 based on power-efficient quad-core Arm® Cortex®-A35 SoC is a low-power, low-cost, entry-level, small-sized SMARC rev 2.0 module. For applications, such as IoT controllers, IoT gateways, wearable and mobile industrial devices, basic HMI, sensor concentrators, requiring good computing performance at low power consumption (1.5W- 5W) and Linux Yocto capability, LEC-PX30 is an ideal solution.
-
product
High Frequency Insulation Tester
HFIT 7.0
The MEDTEQ high frequency insulation tester is a popular device for evaluating compliance with IEC 60601-2-2 and the characteristics of insulation at high frequency
-
product
Build Your Hydrostatic Tester
Start with the basic Model 9901 hydrostatic tester as shown to the left with the following standard equipment:- Hydrostatic test pump, air operated.- 1% ANSI B40.1 Grade 1A stainless steel high pressure gauge.- ANSI B40.1 Grade B air pressure gauge.- Micro adjust precision regulator.- High pressure isolation shutoff valve.- Automatic lubricator.- Stainless steel high pressure manifold.- 1/4" NPT accessory port.- Bleed valve.- Air shutoff valve.- Factory set air pressure relief valve.- 7/16-20 straight thread O-ring boss outlet port (MS33649-04) with -4 male adapter fitting.- 3/4" swivel female hose inlet with strainer.- Stainless steel base plate with rubber feet.
-
product
Burn-In Tester
Universal test bench system. Provides basic electrical measurements at a low cost. Designed for a wide range of electronic products with a dedicated wiring harness. Allows you to expand the scope of functionality. Work in automatic or manual mode. Tailored to the needs of low- and high-volume production
-
product
Short Hot Stick
HS-120R
Standard Electric Works Co., Ltd
● Single foamed hot stick.● Universal sunrise fitting on the head to fit special tool fittings.● Rated at 100 kV per 300mm (5 minutes).● Can be connected to 275 HP HV proximity detector, 21X HVD capacitive HV detector and 277 HP Non-contact HV detector.● Meets IEC 60855.● Reasonable price.● Accessories
-
product
Above Ground Insulator Tester / RF-IT
RF-IT
Hand Held InstrumentEasily locates shorted bolts, replaces bolt to boltUse on structure with or without CPUses Radio Frequency to test effectiveness of above ground insulatorsAuto Shut-Off feature
-
product
Edge Press Technology Bed of Nails Testers
Rand Edge Press Family
Designed for Research & Development and Pre-Production environments to support often reoccurring product design changes. The primary design focus for this fixture is ease in applying engineering changes and resilience to the abuse of applying multiple engineering changes without damage. In R&D and Preproduction, design changes and updates can occur every week. This Rand fixture, unlike normal test fixtures was designed to be easily taken apart and updated. Constantly disassembling modifying and reassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for multiple updates requiring machining, drilling and wiring changes.
-
product
Scott Type Crease-Flex Abrasion Tester
TF119
TESTEX Testing Equipment Systems Ltd.
Scott Type Crease-Flex Abrasion Tester, to determine the crease-Flex abrasion resistance of leather, rubber cloth etc. The force loaded on specimen, distance between grips and the two-way distance can be adjustable. And the force loaded on specimen is of spring type.
-
product
Digital 125 Amp Battery Load Tester
6033
• Heavy load enables the 6033 to detect bad batteries missed by other electronic testers• Automatically computes the CCA of the battery under load• Kelvin connected digital meter displays the following values:• Current Battery Voltage• Maximum Voltage reading• Minimum Voltage reading• Automatic load cycle• PATENTED• Made in USA of US and Global Components
-
product
In-Circuit Testers
Whether you’re choosing from our stand-alone manually loaded ICT tester all the way to our fully automatic In-line test system, Acculogic has the solution for you!Acculogic’s Scorpion family of automated test equipment and in-circuit fixture-based testers were created with one underlining theme in mind: “Cost-effective Testing”.
-
product
Digital Insulation Tester
SK-3502
125V/250V/500V/1000V, Comparator Function., Data Memory (up to 100 data)., Low Resistance Measurement., AC/DC Voltage Measurement., Enhanced Safety Functions.
-
product
Micromotor Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test of DC micromotors.
-
product
Auto Water Vapour Permeability Tester
TESTEX Testing Equipment Systems Ltd.
Auto Water Vapour Permeability Tester, to determine the water vapour permeability of various textile and garment fabric, coating fabric, composite, sportswear and industrial fabrics. Auto Water Vapour Permeability Tester complies with ASTM E96, ISO8096, BS 3424, etc.
-
product
SOLAR CELL TESTER
The tester is designed for terrestrial solar cell incoming/outcoming inspection with the purpose of checking and optimizing parameters and preventing manufacture defects of solar modules. Solar cells are not heated in process of inspection due to the use of xenon pulse lamp installed in the tester.
-
product
Conductive Footwear Tester
SLTM-1
SLTM-1 Conductive Footwear Tester checks conductive footwear automatically. The SLTM-1 Conductive Footwear Tester automatically and accurately measures the exact amount of resistance in conductive footwear and body grounding devices, ensuring a static control environment. It is ideal for dangerous, potentially explosive areas or areas in the electronic industry where static can destroy sensitive components. Stand on the foot plates and the unit’s direct-reading dial with graduated, color-coded scale indicates the exact amount of resistance. Shipped complete and ready to operate. Has 8 feet of 18-3 type SJ power cord that plugs into any grounded 120-volt AC power source. This unit measures 17 x 12 inches and weighs less than 6 1/2 lbs. All conductive footwear and body grounding devices, such as LEGSTATS, must be worn in pairs. SLTM-1 passes conductive footwear with resistance less than 2.5 MEG Ohm.
-
product
Flying Probe Testers
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
-
product
Environmental Testers
Environmental tests are used to verify a piece of equipment can withstand the rigors of harsh environments.
-
product
Flocculation Jar Tester
LD-LFC-A12
Flocculation Jar TesterLD-LFC-A12is designed to stimulate the process of adding reagents, precipitation, coagulation reaction which occurs in water testing procedures. Features desktop, 6 round shaped or square shaped beakers, each with 1.0 L and 1.5 L capacity respectively. With 10 to 1000 rpm speed, this flocculation jar tester conducts synchronous as well as independent running operations. It is used to carry out the jar test during water treatment procedure.
-
product
Megger Tester
Shenzhen UYIGAO Electronic Technology Co., Ltd
Megger is an instrument which in addition to measurement of high resistance can be used to test the quality of the insulation.
-
product
Frazier Differential Pressure Air Permeability Tester
The Low Pressure Air Permeability Machine was developed by the National Institute of Standards and Technology of measuring the air permeability of textile type materials. and It is the acknowledged standard of the U.S. Government and the U.S. Textile Industry. The second model, High Pressure Air Permeability Machine is produced on the same principle as the Low Pressure Machine, but designed with a much greater versatility for use through its higher attainable airflow and differential pressure. Both models are extremely accurate and reliable, very easy to operate, and nearly maintenance free.
-
product
AC/DC Mini Digital Clamp Tester (CE)
M-280
MULTI MEASURING INSTRUMENTS Co., Ltd.
30mmφ CT window and ultra compact size. Conform to IEC safety requirements. Low cost and multi-function clamp tester. Max. and Min.hold function. Data-hold function and auto power off. Auto zero adjustment for DC current offset.
-
product
High-acceleration Shock Tester
DP-1200-18
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
product
Guardian Multi-Channel Hipot Tester
19020
Chroma Systems Solutions, Inc.
The Guardian 19020 enables users to save space on the production line since there is no need to purchase multiple Hipot testers. Its one time multi-channel test can increase the efficiency of electrical regulatory testing. It improves productivity and reduces the risks of testing for products that require only hipot testing.
-
product
HYBRID LED CIRCUIT TESTER, 12-42V
MD1651
*Tests standard automotive electrical DC 12-42V circuits*Safe for low current circuits and hybrid vehicles*Automatic voltage identification featuring blue for under 40V and red for over 40V
-
product
SCSI CABLE TESTER
ST123
Continuity tests alone are not sufficient to qualify SCSI cable assemblies. Proper testing of SCSI cables must include a test for correct connection of twisted pairs and shielding. Continuity tests check only that wires are making connections on both ends of a cable.Twisted pairs in the cable must be matched with the correct SCSI signal pairs - otherwise, it is possible to have a SCSI signal (signal and ground pair) placed on wires that are not in the same physical twisted pair (see diagram at right). This will cause crosstalk with resultant SCSI errors.
-
product
Electrician & Technician Testers
EVSE's Electrician and Technician testers are created for installation professionals, and are small and durableenough to be carried in a toolbox. These weatherproof handheld units allow new chargers to be checked after installation, verifying a number of vital power and safety requirements, as they simulate the connection a charger makes with an electric vehicle. Simply plug the charger's J1772 connector into the tester's receptacle and you are ready to evaluate operation.
-
product
Hardgrove Grindability Index Tester
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
Hardgrove Grindability Index Tester is designed to measure the grindability of coal, which is widely applied in coal industry, power plant ,metallurgy and chemical industry.
-
product
Single Phase Socket Tester
K-280
TESCO Knopp’s K-280 Single Phase Socket Tester is designed to detect short circuits, backfeed and wiring errors in a 120/240 volt, 3-wire, single phase self-contained meter socket.
