Short Testers
Detect unintended circuit connectivity and insulation defects.
-
product
Geotextile Water Flow Capacity Tester
TG050
TESTEX Testing Equipment Systems Ltd.
The flow of water within the plane of a geotextile or geotextile-related product is measured under varying normal compressive stresses, with typical hydraulic gradients and with defined contact surfaces.
-
-
product
Network Cable Tester
PA-40
The PA-40 is designed to check both shielded and unshielded twisted pair (STP/UTP) and coaxial BNC-type network cables. With the push of a button, it tests all wires for continuity, miswiring, and polarization. Dual-colored LEDs let you identify correct and reversed pairs; using the included remote unit, cables may be tested before installation or after installation. Features tip/ring polarity test. Uses 1 9V battery.
-
product
Programmable Ground Resistance Tester
AllWin Instrument Science and Technology Co., Ltd.
Executive test in 40A/60A of UL60950-1Test resistance range 0~510m ohmOutput current range 5~40A
-
-
product
Closed Cup Flash Point Testers
Labodam closed-cup flash point testers are compact, stand-alone solutions which determine the low temperature operability in diesel fuel, biodiesel, blends and gas oils. They are designed as per Test Methods for Flash Point of Petroleum Products (Pensky-Martens Closed Cup Methods).
-
product
Coatings On Concrete Adhesion Tester
106/6
The Elcometer 106/6 Adhesion Tester has been specifically designed to measure adhesion strength of coatings on concrete.
-
product
Connector Board for Cable and Harness Tester
CB49
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors.
-
product
Cut Susceptibility Tester
King Design Industrial Co., Ltd.
Equipment conforms to IEC61730 MST12 specification. Pre- or post-round can be selected for control wiring connection. With weights block’s positioning pin is removed before test; and is inserted in the rear positioning hole for the remaining time. Equipped with rings at both front and rear end; used to connect a rope and control the driving direction. Use replaceable special cutting chip.
-
product
Heat Seal Tester
HST-H3
Heat seal tester (Laboratory heat sealer) is to determine the suitable sealing parameters (sealing temperature, dwell time and pressure) for materials.
-
product
Indentor Extension Tester for Types A and D
Applicable standards specify two extensions for an indentor, 2.50mm and 2.54mm, and the indentor testers are available for two models A and JA corresponding to the respective extension. Each indentor extension tester set is complete with two gauges, one for hardness value of 50 and the other for hardness value of 2.
-
product
80-500V AC/DC Twin-Lead Circuit Tester
1927
Peaceful Thriving Enterprise Co Ltd
*Handy pocket-clip.*Bright neon indicator.*With UL and cUL Approval.*Insulated housing and test leads.*Check voltage on 80-500V AC/DC.*Built-in lamp will glow if circuit is live.
-
product
Condensation Tester
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Condensation tester simulates the damaging effects of outdoor moisture attack by condensing warm water directly onto test specimens. In a few days or weeks, the tester can reproduce the damage due to moisture that occurs over months or years outdoors.
-
product
AC/DC Withstanding Voltage& Resistance Tester
TH9201
Changzhou Tonghui Electronic Co., Ltd.
TH9201 AC/DC withstanding voltage & insulation tester is a kind of Hipot Tester. Due to simple and compact structure, mature technique, brand new structure and operating interface, the operation becomes more convenient, and more practical functions are included as well. TH9201S can be widely applied in transformer, device, component especially for winding safety inspection.Withstanding voltage test
-
product
General ELCB Testers
TEL1-x Series
Standard Electric Works Co., Ltd
The TEL1 is the Basic Test Equipment an Electrician cannot do without. TEL1 is a Dual Function Test Instrument utilized to Verify Electrical Wiring Connections and the Functioning of Earth Leakage / Residual Current Detectors devices by forcing the ELCB/RCD to trip.
-
product
Exhaust Back Pressure Tester
33600
Use to test for clogged or obstructed catalytic converters and mufflers. Fast and easy to use - threads into Oxygen Sensor Port. Includes 12mm and 18mm adapters to fit most domestic and imported vehicles. Gage measures 2 1/2" diameter and has dual scale: 15 PSI and 1.00 Kg/Cm2. Hose is 41" long.
-
product
Battery Tester
TMC-2001RTS
The TMC-2001RTS is our newest member of advanced battery testers. We integrated in a very small and lightweight housing all facilities for modern battery and UPS maintenance. Best price/performance ratio.
-
product
Oil Pour Point Tester
Weshine Electric Manufacturing Co., Ltd
WESHINE’s fully-integrated, automatic cloud and pour point apparatus(VS-9612 Cloud and Pour Point Tester) offers precise and convenient flow testing of petroleum products, biodiesel fuels, additives and lubricating oils.
-
product
CTEK PRO Battery Tester
40-209)
Complete with an integrated printer, it’s now easier than ever to determine and present the current state of a battery and electrical system with the CTEK PRO Battery Tester. The PRO Battery Tester performs quick, simple, and accurate battery or system testsin seconds without heat, sparks, or user interpretation. The results can then be printed and reviewed immediately with customers for added impact to preventative maintenance routines and customer service. The CTEK PRO Battery Tester is patented and features a 2-year warranty.
-
product
IEC60065 Socket Torque Balance Tester Torsion Tester
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
product
Autosampling Dissolution Tester with Built-In Sample Collector
Vision AutoPlus & Vision AutoFill
The Vision® AutoPlus™ is a modern upgrade of the popular Hanson legacy AutoPlus™ autosampler. The Vision AutoPlus comes with a choice of 6 or 8 sampling channels, and DissoScan™ (1-bath) or Maximizer™ (up to 3 baths) configurations. Precision syringe pump mechanics, all-inert tubing and valves, and color touchscreen programming with up to 100 protocols are standard on each instrument.The Vision® AutoFill™ is a sample collector designed for seamless integration with the Vision AutoPlus to save space and to provide a 360 degree view for visual monitoring of the collection process.. Vision AutoFill accessories include choice of collection racks with 13 x 100 or 16 x 100 mm test tubes for UV-Vis, 12 x 32 mm vials for HPLC, sample trays with 12 x 32 mm vials for UPLC®, and more.
-
product
2CT Method Mini Clamp Tester
M-2002
MULTI MEASURING INSTRUMENTS Co., Ltd.
Compact size and light weight for convenient field use. True rms reading with wide range from 1mA to 200A. Extensional measurements by combination with optional auxiliary CT.
-
product
Voltage Testers
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
product
Insulation Tester
CENTER 360
4 Digits LCD Display, Auto Range For MΩ & Ω, 40 Segments Analog Display, Test Hold Function For Easy Operation, Automatic Zero To Null Lead Resistance
-
product
Heavy Duty Circuit Tester
27000
Designed for testing electrical circuits and locating shorts, grounds, and open circuits. Electrical circuit tester available for checking 6V and 12V systems. Heavy duty battery clip .
-
product
2D Color Temperature Tester
LCC-900
Screens the pass/fail results or module type LED image information that is automatically reset via data transfer with handler unit. Data results are stored in server for unified management.
-
product
Automated Filter Tester
8127
The Automated Filter Tester 8127 is designed to comply with commercial respirator standards around the globe and has a proven track record of durability, reliability, and minimal maintenance, meeting the demanding requirements of manufacturing and quality control environments. Whether you are looking for a stand-alone tester to check a few filters per day or need to integrate your tester in an automated, high volume production line, CERTITEST AFT’s are up to the challenge
-
product
DC Resistance Tester
ZLD-10
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.2-2008Used to measure conductor with nominal diameter ≥0.01～9.0mm or various round or flat copper and aluminum wires and other metal wires with DC current resistance of 100μΩ～99.99Ω;Combination of intelligent DC conductor resistance measuring meter and DC resistance test fixture with sample straightening function;Test range can be selected according to the resistance value of sample, and after clamping samples current resistance value would be displayed;Both potential fixture and current fixture are made of copper;The application of microcomputer control allows for full-automatic completion of test;LED will intuitively display measurement results;
-
product
Heavy-load Pallet Drop Tester KD-500
KD-500
King Design Industrial Co., Ltd.
*To evaluate impact effects of shock, drop and tumble encountered in repair and handling process, so do the safety strength assessment. *The general drop test is against bottom, angle, edge and tumble. According to related specifications you can lift one side of the product by angle to make it drop freely.
-
product
Water Vapor Permeability Tester
QT-WVP
Qualitest Water Vapor Permeability Tester QT-WVP series is used to test the water vapor transmission rate (WVTR) of packaging materials.
