-
Product
Broadband Detectors
-
These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.
-
Product
ESD Event Detector
Novx MiniPulse
-
Simco-Ion's Novx MiniPulse ESD Event Detector is designed for tool and process monitoring. This affordable, small footprint embeddable monitor has been developed to warn of product damage risks at the point of electrostatic discharge. The MiniPulse uses time domain and threshold discrimination to detect pulse electromagnetic energy. Through the use of specific antenna configurations and placement, the MiniPulse can provide ESD event detection for well-defined small areas.
-
Product
Extended Range Ultrasound Detector
PowerBeam 300
-
The PowerBeam 300 accurately pinpoints source of ultrasound to within 1 degree from center and improves the sensitivity of the UL101. The "PB300" was originally designed for the indication and location of corona discharge and arcing on medium/high voltage transformers.
-
Product
Photon Counting Detector - Single Photon Detection with Picosecond Accuracy
PPD
-
The PPD Series is a range of miniaturized single-photon counting detectors containing all the electronics necessary to detect single photons with picosecond accuracy.
-
Product
Slipping Torque Detector
DI-12 series (SL4/SL02/SL15)
-
Torque measurement of tightened screws. Measure how much force the tightened screw is tightened. By capturing the occurrence of slippage with high accuracy and measuring the torque, it is now possible to measure the torque value of a tightened screw. For sampling inspection of products and setting and management of output torque of power drivers.
-
Product
FAult Detector and OScilloscope 7 Functions in 1 Device
FADOS7F1
-
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
Usage of FADOS7F1: Determining faults of all types of electronic cards such as electronic cards of medical devices, textile and any other machines; automobile electronics; computer, monitor, TV, etc. Electronic Components Test: IC, transistor, FET, IGBT, resistor, capacitor, indicator, ect. This device is used to determine the faults at all these electronic components.
-
Product
Temperature Measurement IR Sensors & Detectors
S25 TO-5
-
A single-channel silicon-based thermopile that offers the smallest single element active area size at 0.25mm x 0.25mm in a TO-5 package. Delivers a fast 18ms time constant in Argon encapsulation gas and even faster with Neon gas at 9ms. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C.
-
Product
TERAHERTZ HOT ELECTRON BOLOMETER DETECTORS FROM 0.1 to 70 THz
-
Insight Product Company offers ultrafast superconducting hot-electron bolometers (HEBs) operating at terahertz frequency range. from 0.1 to 70 THz. Superconducting hot electron bolometers HEBs are designed to detect and register the electromagnetic radiation pulses in the frequency range from 0.1 THz to 70 THz.
-
Product
Detectors
-
Keysight detectors offer very flat frequency response versus frequency and temperature and exhibit excellent square law response with very low junction capacitance. Planar Doped Barrier Diode Detectors are available only from Keysight.
-
Product
Gas Detectors
-
CO2, Humidity And Temperature Sensors, Dual Wavelength NDIR CO2 Sensor (Non-Dispersive Infrared) For Superior Stability, User Operated CO2 Calibration, Data Hold & Max/Min/STEL/TWA Function
-
Product
Refrigerant Detectors
-
UEi Test & Measurement Instruments
Is designed and certified to meet the new tougher standards and detect the latest refrigerants.
-
Product
Detectors
-
Marktech offers the broadest line of both silicon and InGaAs detectors commercially available. Our main focus has always been in the area of application solutions to optimize your products performance. Our team of design engineers and R&D scientists are committed to providing you with unsurpassed technical support. Our detector series includes product ranging from UV through SWIR.
-
Product
Photo Detector Laser Power Meters
11PD100-Si
-
Silicon detectors provide a generous aperture for laser beams up to 10 mm in diameter. The threaded aperture allows you to install filters, attenuators, fiber optic adapters or other optics that suit your specific needs.
-
Product
Phase Failure Detectors
DSP
-
Your product The DSP-1L or DSP-1LM is used to protect your three-phase motors against phase loss, imbalance, or reversal. It continuously monitors each phase of your power supply. In case of a problem, it cuts the power to the control circuit to protect the affected motor.
-
Product
Smoke Detector Tester
Solo 365
-
The fire industry’s most popular range of detector test equipment is about to get even better. Solo, the test equipment used world-wide to functionally test fire detectors has a new tester in its range – Solo 365. This exciting innovation provides fire safety professionals with an array of stand-out features which make for faster, simpler and cleaner functional testing of smoke detectors. Key features include automatic generation of smoke which ensures only the amount of smoke needed to activate the detector is produced – minimizing smoke wastage and eliminating the risk of detector contamination. In addition, Solo 365 is light in weight and has a slim-line design which allows easy access into tight spaces – making it possible to test detectors which are hard to access with other portable testers. In response to market feedback, Solo 365 features an LED torch which automatically illuminates when light levels drop, making for easy detector alignment and testing in dark environments. Smoke is generated via newly designed smoke cartridges which fit neatly into the rear of the tester. With no reliance on pressurised aerosol cans, the cartridges can be easily shipped and stored and are unaffected by new regulations, set for 2018, which will affect availability of some pressurised smoke aerosols.
-
Product
Wheel Play Detectors
-
A play detector consists of two plate units on which the wheels of an axle are placed. The plates are moved horizontally in an oscillating fashion by hydraulic cylinders. This movement can be done in different directions. In this way an inspector in the inspection pit can easily check for play on the different components underneath the vehicle. To make it even easier, the remote control unit to start and stop the plate movement has a built-in lamp.
-
Product
Fixed Gas Detectors
DG7 Series
-
Teledyne Gas & Flame Detection
All DGi-TT7 are constructed from a common housing and electronics with the detection properties being determined by the type of sensor (cartridge) used. A wide range of cells are available, these cells are intrisically safe protected, and may be replaced with the detector powered which minimises the system down time. The intelligent, microprocessor driven unit is fully configurable using a wireless hand-held terminal (TLU) or by using the hard wired HART option giving true flexibility to the installer and reduced service costs.Elements such as relay operation and alarm levels are all set via the TLU, a hazardous area approved hand-held unit. The unit may be interfaced directly with a wide range of panels, controllers and PLC’s etc. Its integral daylight readable alphanumeric display indicates local status and alarm level.
-
-
Product
Long Neck Combustible Gas Leak Detector
CD100A
-
UEi Test & Measurement Instruments
The CD100A is the service persons tool designed to detect combustible gas leaks in residential and small commercial applications. Semiconductor sensor responds instantaneously to all combustible gases. The easily adjusted, steady tic rate provides a precise indication of the leak source. The CD100A can be used in tight quarters where others might not fit.
-
Product
Digital Multi-Function Radiation Detector
R500
-
Designed for quick detection, quickly found abnormalHigh sensitive sensor, USB ports, 8 seconds responseComputer data analysis softwareDetection of alpha, beta, gamma, Χ-rayLarge-screen high-definition LCD display
-
Product
High Voltage Proximity Detector
MODEL - 288 SVD
-
Kusam Electrical Industries Limited
It is a designed to alert the user that they are approaching live equipment where dangerous voltage is present.
-
Product
Air Tightness Detector
FQ
-
Fuzhou Fuguang Electronics Co., Ltd.
FQ series air tightness tester is the latest high-precision non-destructive testing equipment developed by Fuguang Electronics. The equipment mainly uses compressed air as the medium to apply a certain pressure to the inner cavity or surface of the product to be tested, and then uses a high-sensitivity sensor to detect changes in pressure to determine the tightness of the product to be tested.
-
Product
Cable Detectors
-
The cable detector makes it easier to find cables in the wall and cable ducts. Here, an adapter or carrier signal from the transmitter is modulated by means of crocodile clips or the adapter to one end of the cable. The other end of the cable can then be found quickly and precisely with the receiver without contact or having to strip the cable insulation. Two-core cables can also be exactly identified in telecommunication and network technology.
-
Product
Beam Position Detectors
-
We offer a wide range of laser beam position detectors for optical alignment including Quadrant Cell Photoreceivers, PSDs, and Thermopile Position Sensors. Please see our Beam Position Sensor Guide for more information.
-
Product
Digital Infrared Thermo Leak Detector
IR-711
-
Shenzhen Calibeur Industries Co., Ltd..
'-4 colors backlight to indicate thermo leak by diviation setting;'- Measurement Range: -40° to 716°F (-40° to 380°C); '- Accuracy : < 0°C： ±3% or ± 3°C ≥0°C： ±2% or ±2°C '- Distance Spot Ratio: 12:1; '- Emissive: fixed at 0.95;'- Response time: 0.5 seconds;'- ℃/℉ selectable;'- Three ranges of leak difference exchange: ±0.5℃, ±3.0℃, ±5.5℃ ±1℉, ±5℉, ±10℉'- Size: : 42*85*185mm'- Weight: 170g'- Power: 1pc 9V Battery .(not included)
-
Product
Toxic, Oxygen and Flammable Gas Detectors
-
We can offer a wide range of flammable gas detection instruments for hazardous areas applications that measure hydrocarbon gases at the %LEL and %vol levels. Product options include explosion-proof and intrinsically-safe designs and the product offering includes technology options for both non-dispersive infrared and catalytic bead sensing methods.
-
Product
Non-contact Phase Sequence Detector
-
Phase detection (normal phase, reverse phase and phase deficiency), Live wire examination, Simple Power detection, Breakpoint location and Line maintenance.
-
Product
ECT / ECA Eddy Current Flaw Detector
EVi
-
United Western Technologies Corp
The EVi works directly with the EddyView Family of probes and accessories. UniWest’s unmatched selection of standard and advanced display features set a new standard for flexibility of applications, ease of use, interpretation of data and overall operator accuracy. The key to the EVi’s ground-breaking performance is the display of a visual image of the surface area under inspection alongside the customary and selectable eddy current signal displays (impedance plane, A-scan or strip charts). The EVi provides a high precision, easily readable display of surface conditions enabling improved interpretation of data while giving more accurate discernment of cracks, pits, gouges and fretting.
-
Product
Detector, Metal, Power, Stud
72-6792
-
*Electronically locates hidden cables gas and water pipes*Traces hidden ceiling joists and wall studs*Senses presence of mains power withut touching live wires*Locates breaks in circuits and cables*Identifies faulty plugs switches and sockets*Incorporates audio signal and indicator light
-
Product
IR Detectors
-
Opto Diode manufactures high performance infrared detectors with a wide variety of active area sizes, cooling alternatives, packaging, windows, lenses, and filters options. These detectors are ideal for gas analysis, emissions monitoring, spectroscopy, process control, flame and fire monitoring. Our A Series lead sulfide (PbS) detectors provide the highest sensitivity in the 1µm to 3µm wavelength region. Our B Series lead selenide (PbSe) detectors deliver the best overall performance in a wider spectral range from 1µm to 5µm. Our multichannel (MCDs) devices are ideal for simultaneous detection of multiple gases including CO2, CO, and other hydrocarbons.
