-
Product
Broadband Detectors
-
These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.
-
Product
Phantom Pharmaceutical Metal Detector
-
The Phantom Pharmaceutical metal detector provides the ideal solution for detection and rejection of the smallest contaminants in tablets and capsules. With its current GMP design and construction suited for FDA compliance, the system meets the stringent QA requirements of the pharmaceutical industry. A free IQ/OQ Validation package is included. Built with a rugged mirrored stainless steel exterior, contact parts are all removable for cleaning without the need for tools. This compact detector can be easily angled and height-adjusted to suit any press configuration. Plus, it’s the only detector that features an electrical powered lift.
-
Product
Radiation Detectors
-
High Purity Germanium (HPGe) DetectorsSilicon Charged Particle DetectorsScintillation DetectorsORTEC is a leading supplier of solid-state, high resolution, semiconductor radiation detectors. These radiation detectors are used in research, commercial industry, environmental protection, health and medical physics, as well as homeland security to detect gamma-rays, X-rays, and charged particles.
-
Product
Gas Detectors
-
International Gas Detectors Ltd
We offer a vast and versatile product range with detector heads for every possible environment. Pioneering the use of addressable gas detection systems IGD today offer the latest networked systems. Our latest addressable gas detection systems network using IGD’s Sentinel+ 2-Wire protocol for enhanced operation and security. IGD is the home of addressable gas detection but we still offer legacy analogue detectors used to interface to older systems.
-
Product
Silicon Based Thermopile Detector: 4 Channels
ST150 Quad
-
A four-channel silicon-based thermopile detector in a TO-8 package. Each active area size is 1.5mm x 1.5mm. Affordable four-channel design with strong output and a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Mini Carbon Monoxide Gas Detector
Model - KM CO-910
-
Kusam Electrical Industries Limited
KM-CO-910 Carbon Monoxide meter detects the presence of Carbon Monoxide (CO) & measures concentrations between 1-1000 parts per million(PPM). The meter indicates the presence of CO by a reading on the LCD & a beeper tone. The beeper function much like clicking of a geiger counter: above 200PPM, the beeper sounds continuously with the concentration of CO; from 35PPM to 200PPM, the beeper sounds discontinuously with the concentration of CO.
-
Product
Ignition Pulse Detector
IP-3000A
-
IP-3000A Ignition pulse detector is a slim and light weighted detector by using amorphous metals fiber element. It is 1/4 in thickness (mass: approx. 1/50) and 1/3 in weight compared with the previous model of Ono Sokki. Also the IP-3000A can obtain constant output from low to high rotation with high sensitivity.Meeting the needs of structure or mechanism in recent gasoline engines, the IP-3000A can easily clamp around an ignition coil cable (the primary side cord of ignition coil or the current cord of electronic distributor). Moreover, heat-resistant design up to maximum operating temperature of +120 C° enables measurement under harsh environment.The IP-3000A Ignition pulse detector can be used with Ono Sokki’s engine tachometer.
-
Product
SF6 Gas Leak Detector
-
Weshine Electric Manufacturing Co., Ltd
1. SF6 quantitative leak detector is an ideal tool and method for sf6 gas trace leakage inspection. It has the advantages of fast, convenient, reliable, and low maintenance cost.2. Especially suitable for occasions with high frequency of use such as factory workshops.3. It is recommended to purchase model LF-200 products during after-sales or inspection, with a total product weight of 7.5Kg, equipped with a portable aluminum alloy crash box.
-
Product
Pen Style Combustible Leak Detector
UTLCD1
-
UEi Test & Measurement Instruments
The UTLCD1 is a professional value Combustion Leak Detector with easy one step operation.
-
Product
Open Path Infrared Gas Detector
IR5500
-
The IR5500 is an open path infrared (IR) gas detector that continuously monitors for flammable gas leaks over large open areas. It monitors in both the LEL-m and ppm-m ranges to detect both small and large leaks. The IR5500 offers the benefits of early detection with its high sensitivity to gas concentrations at the ppm levels.
-
Product
Radar Detectors
-
Explore our collection of premium radar detectors designed to fit your driving style and preferences.
-
Product
In-Line Pinhole Detector
DZK
-
Shanghai Dean Electrical Co., Ltd
DZK portable Pin-hole Instrument is designed and produced in accordance with GB/ t4074.5-2008 standard, which can be used for the user of enameled wire to monitor the continuous performance of paint film in the process of production and use. It takes into account the detection function of the traditional high pressure paint film continuity tester and the advantage of being easy to move and replace, which facilitates the user's detection and use of various environments and multiple cables.
-
Product
3 In 1 Metal Voltage Stud Detector
NT-6352
-
Combined unit to accurately detect live or dead electricity cables, water or gas pipes and wooden studs or battens.LED & buzzer indicators.Depth penetration 18~20mm.Using precision screwdriver for easy unit sensitivity adjustment.Power source: NEDA1604/6F22 (9V) x 1pcs(Not included).Size: 178 x 120 x 34.7mm.
-
Product
Metal Detectors
-
Guarantee the quality of your product with our WIM-Systems metal detectors. Wide variety of metal detectors that will help you to cover your quality controls in the production line, guaranteeing the quality of your products with an adequate inspection.
-
Product
Tunnel Diode Zero Bias Detectors
-
A tunnel diode zero-bias detector is a device that converts microwave and millimeter-wave radio frequency (RF) signals into a DC voltage without requiring an external power source
-
Product
Silicon Drift Detector
Octane Elite (SDD) Series
-
The game changing advancements in the Octane Elite Silicon Drift Detector (SDD) Series take detector technology to the next level. This line of detectors incorporates a new silicon nitride (Si3N4) window, which offers remarkable improvements in low energy sensitivity for light element detection and low kV microanalysis. The Octane Elite Series also uses the widely praised CUBE technology, which yields high speed X-ray data processing within a smaller and fully vacuum encapsulated detector device.
-
Product
Gas Detectors
-
CO2, Humidity And Temperature Sensors, Dual Wavelength NDIR CO2 Sensor (Non-Dispersive Infrared) For Superior Stability, User Operated CO2 Calibration, Data Hold & Max/Min/STEL/TWA Function
-
Product
HV High Voltage Detector
-
The Motwane Manufacturing Company
For decades, Motwane Voltage Detector has been a standard for international quality and safety ratings. Voltage detectors are used to signal the presence of voltage in a conductor since they make visible what we normally can’t see. Its application lies mainly in safety reasons during research, or when a service operation is under way. Most of the time, the monitored conductors come from low impedance sources whose voltage and energies are considered life-threatening.
-
Product
Chatter Detector
Trig-Tek™ 850A/B
-
The Trig-Tek™ 850A/B Contact Chatter Detector provides a means of monitoring the continuity of switch or relay contacts while being subjected to environmental stress. 10 channels Adjustable time interval (1μs to 999 ms) Individual fault light and fault latch per channel Open or closed contact detection
-
Product
Portable Gas And Leak Detectors
-
Portable Gas Detectors, classed as a type of Personal Protective Equipment (PPE), are designed to keep personnel safe from atmospheric gas hazards and allow mobile testing of locations before they are entered. These handheld devices are essential in many areas where gas hazards could occur because they are continuously monitoring at close range to the operator, while stationary and moving.
-
Product
Interceptor Metal Detector
-
Interceptor metal detectors are custom manufactured to achieve superior results in challenging applications. The Interceptor uses a simultaneous multi-frequency operation that effectively processes the transmission and reception of multiple frequencies continuously over a broad spectrum. This revolutionary operation facilitates an improvement in detection capabilities of up to 100% with stainless steel, especially when inspecting traditionally difficult “wet” products.
-
Product
ChromaPoint Detectors
E50
-
Sciences et Techniques Industrielles de la Lumière
E50 series is part of the STIL ChromaPoint detectors.All the optical fibers are passive components, graduated index silica fibers with a 50µm core, an E2000/APC connector for the connection with STIL controller and an FC/APC connector for the connection with STIL optical sensor head.
-
Product
Detector
-
In the measurement setup of SQUID electronics (detector variant), the dc SQUID amplifies the small amplitude signals of the detector with a large bandwidth so that they can be further processed with conventional AD converters.
-
Product
Plugged Chute Detector
-
The Drexelbrook Plugged Chute Detector reliably detects the presence or absence of material flowing through chutes. If process material stops flowing due to a plugged condition, the flush mounted capacitance sensing element will alarm, allowing further action to occur (alerting an operator, shutting down a conveyor belt, etc.).
-
Product
H-Field Burst Detector
BD 11
-
The BD 11 is used to detect a burst or ESD current pulse on a cable, for example in a complex system. This makes it easier to investigate the causes of sporadic faults in the system. It is small and handy, its sensitivity is very high and continuously adjustable.
-
Product
Joist And Stud Detector With Bubble Level
6342
-
Peaceful Thriving Enterprise Co Ltd
Electronically locates hidden wood & metal stud.
-
Product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2320
-
CableTroll 2320 is an indicator for detection of Earth faults (PtG) and short circuit (PtP) faults on multi-core and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
Flaw Detectors
-
Flaw detectors are essential for ensuring the safety and quality of industrial products. They accurately identify defects such as cracks, voids, and inclusions without damaging the materials. Ultrasonic testing is particularly notable for its precision and versatility among the various non-destructive testing methods.
-
Product
The Modern Personal Radiation Detector
D3S PRD
-
The D3S PRD personal radiation detector is a high-speed PRD or SPRD replacement that is a cost-effective radiation detection and preliminary identification device for first-line users. It fits on your belt or even in your pocket giving you radiation alerts for gamma and neutron radiation plus the ability to identify what isotopes have been found. It is the only PRD that detects the presence of radiation and also displays the isotope identified and it does all this in seconds.
-
Product
Multi-spectrum IR Flame Detector
FL4000H
-
The FL4000H is an advanced multi-spectrum infrared (MSIR) flame detector that provides superior false alarm immunity with the widest field of view.
