SPST
Single Pole Single Throw relay.
-
Product
PXI/PXIe Power Relay Module, 24xSPDT, 5 Amp, 50-Pin SGMC Connectors
42-158-002
Relay
The 40/42-158-002 is a PXI/PXIe high density power relay module with 24xSPDT switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
Product
PXI/PXIe Power Relay Module, 25xSPST, 5 Amp, 50-pin SGMC Connector
40-153-003
Relay
The 40/42-153-003 is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
PXI 64 x SPDT Electromechanical Relays
40-148-201
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
Signal Splitters
-
The DAT4530 can convert any process signal (Thermocouples, RTD, mV, Voltage, mA Resistance and Potentiometer) to a voltage or current output (4-20mA, 0-20mA or 0-10V). Each output can be different and it also has a built in limit alarm which is an SPST relay. The DAT4530 is PC programmable with the aid of the Prodat programmer and the Datasoft software which is available from the Datexel down load page. The DAT4530 is also programmable with the aid of 3 DIP switches which can be found on the side of the DAT4530. There is full isolation between the input, power supply, limit alarm output and two outputs.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm - SPST
50-294-134
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm - SPST
50-294-123
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe Power Relay Module,5 Amp, 50-Pin SGMC Connectors
40-158-001-HI
Relay
The 40/42-158-001-HI is a PXI/PXIe high density power relay module with 32xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
Product
8-Ch SPST 12A-250VAC 24VDC Multiplexer with CAN
H620047C2
Multiplexer Module
This module is ideal for switching up to 12A. Composed by eight relays organized in two trees of four with two relays with NC contact available. The module is shielded in order to reduce the radiated interference in high current switchings.
-
Product
PXI-2569 , 31-Channel, 2 A, SPST PXI Relay Module
778572-69
Relay
31-Channel, 2 A, SPST PXI Relay Module—The PXI‑2569 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It is fully software programmable and contains a 32,000‑step scan list for deterministic scanning capability. This module offers maximum relay density, so it is ideal for medium-power automated test loads.
-
Product
PXI 100 x SPST Electromechanical Relays
40-145-201
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
(8×32)-Ch 0,5A-200VAC Matrix
YAV90062
Matrix Switch Module
256 relays SPST matrix (4×64 1 pole) or (4×32 2 poles). Max switching 10W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 100xSPST, Normally Open
40-145A-201
Relay
The 40-145A-201 (PXI) and 42-145A-201 (PXIe) 100xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
LXI Optical Switching - 32:1 Multiplexer Plugin Module
65-281-315
Multiplexer Module
The 65-281-315 32:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
Relay
40-145-101
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
12-Ch SPST 4A-250VAC 24VDC High Current Power Switching
YAV90PIN
Switch Module
The YAV90PIN board is designed to cover the need to control the available power supplies in a test system to the device under test. A VPC 90 series connector is used as interface with the fixture, guaranteeing more than 20.000 mating cycles. Two connector contacts per relay contact are used.
-
Product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
Relay
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
Product
PXI 100 x SPST Ruthenium Reed Relay Switching
40-140A-221
Relay
This range of high density reed relay switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 32xSPDT
40-148A-001
Relay
The 40-148A-001 (PXI) and 42-148A-001 (PXIe) 32xSPDT relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
PXI Power Relay Module, 12xSPDT, 16 A, With Interlock
40-161A-101-HI
Relay
The 40/42-161A-101-HI is a PXI/PXIe 12xSPDT power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
Level Monitoring
-
Magnetic level switches are used for the monitoring and control of liquid level in tanks. These level switches are specifically manufactured to customer specifications. The float switches are manufactured with a hermetically sealed contact which is located within the guide tube. The float sliding on the tube contains a ring magnet which activates the sealed contact in a non-contacting fashion. The sealed contacts are available as SPST (N/O or N/C) or SPDT (N/O + N/C). The float sliding up and down on the guide tube is the only moving part on the M-series magnetic float switches.
-
Product
80/24 Channel SPST Plug-in Switch Card
1260-118/118A
Switch Card
The Astronics 1260-118/118A is an 80/24-channel, SPST (Form A) plug-in relay card for the Adapt-a-Switch™ platform.
-
Product
PXI 40Amp 14Volt 2xSPST Automotive Relay
40-180-001
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDCThe 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
PXI/PXIe Power Relay Module, 3xSPDT, 20 Amp
42-166-102
Relay
The 40/42-166-102 is a PXI/PXIe high density power relay module with 3xSPDT switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
-
Product
PXI/PXIe Power Relay Module,5 Amp, 50-pin SGMC Connector
40-153-003-HI
Relay
The 40/42-153-003-HI is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
Product
PXI/PXIe Power Relay Module, 1xSP4T, 20 Amp
42-166-203
Relay
The 40/42-166-203 is a PXI/PXIe high density power relay module with 1xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
-
Product
PXI/PXIe High Density Reed Relay Module, 50xSPST
40-140B-021
Reed Relay
The 40-140B-021 (PXI) and 42-140B-021 (PXIe) are 50xSPST general purpose switching modules. They are part of a range of high density relay modules using ruthenium reeds available in 50x, 75x and 100x Normally Open SPST configurations. Connections are made via a front panel 200-pin female connector.
-
Product
PXI Switched Guard Reed Relay Module, 26x SPST
40-121-001
Reed Relay
The 40-121-001 provides 26x SPST switches in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
Product
PXI 25 x DPST Electromechanical Relays
40-146-002
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXI 20Amp 28Volt 2xSPST Automotive Relay
40-180-011
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 37-Pin D-type Connector
40-158-104
Relay
The 40/42-158-104 is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A. User connection is via a 37-pin D-type male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
