SPST
Single Pole Single Throw relay.
-
Product
PCI 32xSPST Shielded Reed Relay Card
50-125-021
-
The 50-110/115 range of PCI shielded switching cards are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
PCI 32xSPST Reed Relay Card
50-115A-021
-
This is the 32xSPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PXI 50 x SPST Ruthenium Reed Relay Switching
40-140A-021
-
This range of high density reed relay switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
High Density 1xN mux or 2xN Matrix Switching Systems
JX Series
-
This compact and economically priced series can be used as either 1xN multiplexers, 2xN matrices, or individual switches. As multiplexers, they can be used as a large number of individual muxes or jumpered together to form as large a mux as you need to switch a large number of inputs or outputs to one common port. As a 2xN matrix they allow you to switch any number of signals between two ports of a DVM, DMM, LCR, or other type of meter or supply. Individual relay modules are available for other configurations requiring discrete SPST or SPDT relays with standard or power relays.
-
Product
Low Profile PCI 8 Reed Relay Output
8012
-
The 8012 Low Profile PCI digital interface provides eight Reed relay outputs (SPST) and eight optically isolated inputs. Reed relays are well suited for low current applications. The relays are normally open, and close when energized. The board is MD1 Low Profile and Universal Bus (3.3V and 5V) compatible.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm - SPST
40-294-112
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXIe Power Relay Module, 6xSPDT, 16 A, With Interlock
42-161A-102-HI
-
The 40/42-161A-102-HI is a PXI/PXIe 6xSPDT power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
PXI/PXIe High Density Reed Relay Module, 100xSPST
40-140B-221
-
The 40-140B-221 (PXI) and 42-140B-221 (PXIe) are 100xSPST general purpose switching modules. They are part of a range of high density relay modules using ruthenium reeds available in 50x, 75x and 100x Normally Open SPST configurations. Connections are made via a front panel 200-pin female connector.
-
Product
PCI 50xSPST Shielded Reed Relay Card
50-125-121
-
The 50-110/115 range of switching cards are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female connector. For applications requiring improved bandwidth and crosstalk performance please look at our 50-120/125 range of shielded reed relay cards.
-
Product
PXI/PXIe Power Relay Module, 1xSP4T, 20 Amp
42-166-203
-
The 40/42-166-203 is a PXI/PXIe high density power relay module with 1xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
-
Product
SIMRC - 8 x Reed Relay Module, SPST
1010-R-8-1-5/1D
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
PXI-2520, 80-Channel, 2 A, SPST PXI Relay Module
778572-20
-
80-Channel, 2 A, SPST PXI Relay Module—The PXI‑2520 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2520 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
Product
PXI Solid State Switch Module, 6xSPST, 10 A, Hardware Interlock
40-182A-011-HI
-
The 40-182A-011-HI has 6 off high current SPST switches with hardware interlock in two PXI slots and is part of our range of high power solid state switching solutions.
-
Product
PXI 25 x DPST Electromechanical Relays
40-146-002
-
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
NI-9482, 4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module
783906-01
-
4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module - The NI‑9482 directly connects to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to an electromechanical relay for switching signals up to 60 VDC (1 A) or 250 Vrms (1.5 A), features channel‑to‑channel isolation, and has a LED that indicates the status. The shock and vibration rating for the NI‑9482 is limited compared with other CompactDAQ and CompactRIO modules because of the mechanical relays on the module.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm - SPST
50-294-124
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe Power Relay Module, 32xSPDT, 5 Amp, 50-Pin SGMC Connectors
40-158-001
-
The 40/42-158-001 is a PXI/PXIe high density power relay module with 32xSPDT switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
Product
SP1T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
Product
PXI 32 x SPST Reed Relay
40-115-121
-
This is the 32xSPST version of our 40-110/40-115 range of reed relay switching modules which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 510 Ohm - SPST
40-294-114
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
LXI Optical Switching - 32:1 Multiplexer Plugin Module
65-281-315
-
The 65-281-315 32:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
Level Monitoring
-
Magnetic level switches are used for the monitoring and control of liquid level in tanks. These level switches are specifically manufactured to customer specifications. The float switches are manufactured with a hermetically sealed contact which is located within the guide tube. The float sliding on the tube contains a ring magnet which activates the sealed contact in a non-contacting fashion. The sealed contacts are available as SPST (N/O or N/C) or SPDT (N/O + N/C). The float sliding up and down on the guide tube is the only moving part on the M-series magnetic float switches.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm - SPST
40-294-111
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Power Relay Module, 10xSPST, 16 A, With Interlock
40-161A-003-HI
-
The 40/42-161A-003-HI is a PXI/PXIe 10xSPST power relay modulewith optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
12-Ch SPST 4A-250VAC 24VDC High Current Power Switching
YAV90PIN
-
The YAV90PIN board is designed to cover the need to control the available power supplies in a test system to the device under test. A VPC 90 series connector is used as interface with the fixture, guaranteeing more than 20.000 mating cycles. Two connector contacts per relay contact are used.
-
Product
Serial to Relay Interface Boards
Model 2364 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
Product
High Density Switching PXI Card
GX6138
-
The GX6138 is low cost 3U switching card with 38 individual low level SPST Form A relays capable of switching 0.5 A at 200 VDC. The GX6138 is ideal for applications requiring high density switching.
-
Product
PXI 64 x SPDT Electromechanical Relays
40-148-201
-
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXIe Power Relay Module, 10xSPST, 16 A
42-161A-003
-
The 40/42-161A-003 is a PXI/PXIe 10xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
PXI 20Amp 28Volt 4xSPST Automotive Relay
40-180-111
-
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
