PXI Carriers
-
Product
PCI & PXI Signal Amplifiers
-
Low power supply rails, a main part of the PXI, cPCI and PCI equipment, are a common cause for an inability to produce high voltage output. Tabor Electronics’ new amplifiers convert the supply rails to higher voltage suitable for signals up to 40Vp-p, thus solving thit problem.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-125-HI
Programmable Resistor Module
The 40-230-125-HI (PXI) and 42-230-125-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 13.6kΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Programmable Step Attenuator Module, DC to 26.5 GHz
M9168C
Attenuator
The M9168C is a programmable step attenuator module based on PXI hybrid platform. The M9168C operates from DC to 26.5 GHz with a guaranteed 0.03 dB insertion loss repeatability for each section throughout the 5 million cycles operating life. Superior attenuation accuracy across a wide operating temperature range ensures precise measurements.
-
Product
PXI 8 Slot BRIC 210x8 2-pole (7 sub-cards)
40-561A-122-210X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 12-Slot BRIC Matrix, 320x16 1-Pole (10 sub-cards)
40-558-121-320X16
Matrix Switch Module
The 40-558-121-320x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-041-HI
Programmable Resistor Module
The 40-230-041-HI (PXI) and 42-230-041-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 201kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 12-Slot BRIC Matrix, 1344x6 1-Pole (16 Sub-cards)
40-558-121-1344X6
Matrix Switch Module
The 40-558-121-1344x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 32 Channel
41-761-001
Simulator
The 41-761-001 is a low voltage 32-channel output module ideal for simulating theoperation of a thermocouple, also available with 24, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 264x8, 6 Sub-cards
40-567A-106
Matrix Switch Module
The 40-567A-106 is a PXI 1-pole 264x8 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 100VDC/70VAC. The 40-567A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female DIN
510140141-2
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female DIN
-
Product
PXI Single 32x8 Matrix, 2 Pole Switching
40-531-022
Matrix Switch Module
Model 40-531 very high density matrix modules are configured as a 32x8, while the 40-532 modules are configured as a Dual 16x8. Both modules are available in a choice of reed relay formats: 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching coaxial signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules. For example, seven PXI modules will form a 224x8 Matrix, a total of 1792 crosspoints in a 7-slot PXI Chassis.
-
Product
PXI Resistor Module 2-Channel 1.5R to 2.04k with SPDT
40-293-122
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 4 Slot BRIC 60x16 1-Pole (4 sub-cards)
40-561A-021-60X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 4x4 20GHz Matrix with Termination
40-787-528-4X4-T
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module. The matrix is available with optional terminated inputs to avoid the creation of standing waves on unconnected input cables.
-
Product
PXI Power Supply
-
A PXI power supply provides the required power for a test application or additional devices. A constant output voltage is generated from the stabilized voltage of the PXI chassis.
-
Product
Dual-Port HS-1760 Test & Simulation PXI Express Module
PXIe-C1760
-
Avionics Interface Technologies
3U PXI form factor fits into PXIe or PXI hybrid slotTwo independent ports programmable as NC or NT(s) simultaneouslyTwo SFP sockets accepts FC-0 AS5653 or AS5625/AS5627 transceiversSupports NC-to-NT transfers, NT-to-NC Transfers, Mode Codes, and BroadcastFull control of sequence and exchange managementSupports large file exchangesFull Monitoring of all Bus TrafficTriggering and FilteringFull Error InjectionSupports DMA for high speed streaming of data to/from the boardIRIG-B Time Code Encoder/Decoder for Data CorrelationOptional Special FC-0 physical layer compliance with SAE AS5653Optional fcXplorer Analyzer for decoding HS1760 frames
-
Product
PXI Hybrid Amplifier/Attenuator
M9352A
Attenuator
The M9352A modules are custom built and tested to nominal* performance characteristics. Full regulatory and safety testing has been performed. This product has the same warranty and support services as other Keysight instruments. Because it is custom built, Keysight recommends checking availability and delivery information before ordering the product.
-
Product
PXI 2A Multiplexer, 4-Bank, 4-Channel, 8-Pole
40-614C-009
Multiplexer Module
This 4-bank, 4-channel, 8 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-321-HI
Programmable Resistor Module
The 40-230-321-HI (PXI) and 42-230-321-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 925Ω with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 2 Slot BRIC 44x8 2A 1-Pole Matrix
40-567-201
Matrix Switch Module
The 40-567 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-567 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 4Ω to 5.82MΩ
40-298-152
Programmable Resistor Module
The 40-298-152 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Prototyping Module, 1-Slot, 9-Pin D-Type
40-225A-701
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Camera Link PXI Output Module
-
It is a PXI module to output as a camera link signal NTSC video signal.For outputting a trigger signal when you have the image conversion, you can ignore the delay at the time of conversion.
-
Product
PXI Resistor Module 4-Channel 1R to 510R with SPDT
40-293-114
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 30 A
40-667C-012
Multiplexer Module
The 40-667C-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI 8 Slot BRIC 330x8 2-pole (11 sub-cards)
40-561A-122-330X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2 Slot BRIC 60x8 2-Pole (2 sub-cards)
40-561A-222-60X8
Matrix Switch Module
The 40-561A-222-60x8 is part of a range of high-density PXI BRIC matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays.
-
Product
PXI Potential Divider Module 12-Channel (no resistors fitted)
40-282-021
Programmable Resistor Module
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
Product
PXI 2-Slot BRIC Matrix, 128x8, 1Pole (2 Sub-cards)
40-558-201-128x8
Matrix Switch Module
The 40-558-201-128x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 12-Slot BRIC Matrix, 792x4 1-Pole (18 Sub-cards)
40-562B-321-792X4
Matrix Switch Module
The 40-562B-321-792X4 is a high density BRIC12 matrix module with a size of 792x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
