PXI Carriers
-
Product
Single 24x4 1-Pole High-Density PXI Matrix Module
40-520-402
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 3Ω to 5.82MΩ
40-251-052
Programmable Resistor Modules
The 40-251-052 is a programmable resistor module with 2 channels which can be set between 3Ω and 5.82MΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 2.5Ω to 773kΩ
40-251-143
Programmable Resistor Modules
The 40-251-143 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 773kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-042-HI
-
The 40-230-042-HI (PXI) and 42-230-042-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 392kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
-
Product
PXI 5A Fault Insertion Switch 5-Channel
40-196-101
Fault Insertion Unit
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
PXI High Density MUX BRIC, 2-Chan, 160-Pole
40-570-012
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI 16x8 2-Pole 2A Matrix
40-518A-002
Matrix Switch Module
The 40-518A-002 is a 16x8 2-pole medium density matrix module and is designed for switching medium voltage/power signals in test applications where reed relays do not have sufficient rating. They are also suitable for telecoms applications where send and return signals need to be switched simultaneously.
-
Product
Single 16 to 1 50 600MHz PXI RF Multiplexer
40-764-001
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
PXI 12-Slot BRIC Matrix, 154x8 2-Pole (7 sub-cards)
40-562B-322-154X8
Matrix Switch Module
The 40-562B-322-154X8 is a high density BRIC12 matrix module with a size of 154x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Monitored Multiplexer, Quad 25-Channel, 1-Pole
40-619-104
Multiplexer Module
The 40-619-104 is a high density PXI 2 A multiplexer module in quad 25-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-030-HI
Programmable Resistor Module
The 40-230-030-HI (PXI) and 42-230-030-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 6.97kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
12-Slot PXI chassis
PXCe4012
Chassis
The PXI chassis of the PXC family are very space-saving, since the measuring cards are installed horizontally instead of vertically in contrast to the usual PXI chassis. Instead of the usual 4-6 U, only 1/2 U are required in the test system.
-
Product
PCIe to PXI Remote Control Interface Kit
41-924-001-KIT
Remote Control
The kit is supplied with a PCIe card which can plug into any PC PCIe slot, a PXI module for insertion into Slot 1 of a PXI chassis and 3m lead to connect the two parts together. The interface uses a single lane PCIe connection from the PC to provide a software transparent link from the PC PCIe backplane to the PXI backplane. The supplied 3m shielded lead ensures the system has robust operation and an adequate separation distance between the PC and the PXI chassis.
-
Product
PXI 4-Slot BRIC Matrix, 88x8 1-Pole (4 Sub-cards)
40-562B-021-88X8
Matrix Switch Module
The 40-562B-021-88X8 is a high density BRIC4 matrix module with a size of 88x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXIe-5423, 40 MHz Bandwidth, 2-Channel, 16-Bit PXI Waveform Generator
785116-01
Waveform Generator
The PXIe-5423 is a 40 MHz arbitrary waveform generator capable of generating user-defined, arbitrary waveforms and standard functions including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -12 V to +12 V and uses a fractional resampling method to precisely generate waveforms. The PXIe-5423 also features advanced synchronization and generation features like waveform scripting and streaming.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-216-HI
-
The 40-230-216-HI (PXI) and 42-230-216-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 1.8kΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781426-02
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
PXI 4-Slot BRIC Matrix, 66x8 1-Pole (3 Sub-cards)
40-562B-021-66X8
Matrix Switch Module
The 40-562B-021-66X8 is a high density BRIC4 matrix module with a size of 66x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8-Slot BRIC Matrix, 66x16 1-Pole (6 sub-cards)
40-562B-121-66X16
Matrix Switch Module
The 40-562B-121-66X16 is a high density BRIC8 matrix module with a size of 66x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 12-Slot BRIC Matrix, 748x4 2-Pole (17 sub-cards)
40-562B-322-748X4
Matrix Switch Module
The 40-562B-322-748X4 is a high density BRIC12 matrix module with a size of 748x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8-Slot BRIC Matrix, 176x4 2-Pole (4 sub-cards)
40-562B-122-176X4
Matrix Switch Module
The 40-562B-122-176X4 is a high density BRIC8 matrix module with a size of 176x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Three Channel Function Generator
41-620-003
Function Generator
The 41-620 is a compact 3 channel function generator provided in a PXI 3U single slot module. It is capable of generating sine waves to 10MHz with 48-bit frequency resolution referenced to the 10MHz PXI clock or to an external standard. The 41-620 can generate arbitrary waveforms loaded into the internal 256k memory, allowing the function generator to emulate many waveform types, including the typical waveforms of automotive and aerospace sensors.
-
Product
PXI High Density MUX BRIC, 10-Chan, 80-Pole
40-570-115
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI Single SP4T Multiplexer 26.5GHz 50 SMA
40-784A-131
Multiplexer Module
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1Ω to 122Ω
40-253-112
Programmable Resistor Modules
The 40-253-112 is a programmable resistor module with 1 channel which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXI Microwave Multiplexer, Dual SP4T, 26.5GHz, 50Ω, SMA, Terminated
40-785C-432-T
Microwave Multiplexer
The 40-785C-432-T (PXI) and 42-785C-432-T (PXIe) are dual SP4T 26.5GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI 2 Banks of 40 Channel 2 Pole MUX
40-615-022-2/40/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXIe-1086DC, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), DC Power Supply, Up to 12 GB/s PXI Chassis
787137-01
Chassis
PXIe, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), DC Power Supply, Up to 12 GB/s PXI Chassis - The PXIe‑1086DC incorporates hot-swappable, redundant DC power supplies as well as hot-swappable, front-accessible, redundant cooling fans. These high-availability features improve the mean time between failure (MTBF) and mean time to repair (MTTR) of the PXI system. The PXIe‑1086DC monitors power supply health/voltages, air intake temperature, and fan health/speed; it provides any failure feedback with the status LEDs located on the chassis. This chassis is ideal for test, measurement, and control applications with demanding system uptime requirements.
-
Product
PXI 5A Power Multiplexer, 2-Bank, 24-Channel
40-651A-002
Multiplexer Module
The 40-651A-002 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
