PXI Carriers
-
Product
M-Module Carrier for CompactPCI (3U)
i3002
-
The i3002 provides a high-performance CompactPCI bus gateway to the M-module interface. The i3002 has a 3U form factor. Two M-modules can be mounted on the i3002. The M-module interface of the i3002 complies with the M-module specification. The M-module interface feature A8, A24, D16 and D32 access types.
-
Product
PXI Very High Density Multiplexer, 99-Channel, 2-Pole
40-675A-002-99/2
Multiplexer Module
The 40-675A-002-99/2 is a 99-channel, 2-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI 3A Power MUX BRIC, 3-Channel, 48-Pole
40-571-003
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI Load Resistor Module 10 Ohm to 2.56k
40-292-012
Load Resistor Module
A simple solution for applications requiring a programmable load resistor with up to 15W power handling. It is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
Product
PXI Opto-Iso Digital I/O 32bit out 16bit in
40-490-002
Digital I/O
The 40-490 Digital I/O Modules are designed for applications requiring optically isolated digital I/O, typically in industrial automation. This modules features 32 digital outputs and 16 digital inputs which may be programmed by word or individual bit. Power for the isolated section of the module is built onto the board in model 40-490-001, or this can be supplied externally in model 40-490-002.
-
Product
PXI 2A Multiplexer, 8-Bank, 4-Channel, 4-Pole
40-614C-005
Multiplexer Module
This 8-bank, 4-channel, 4 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
BRIC™ - Large PXI Matrix Modules
-
High Density Packaging and Integrated BackplanesWith Pickering's BRIC Large PXI Matrix Modules, the use of high density packaging and integrated backplanes enables a large matrix to be implemented with no user configuration or special matrix expansion kits. These matrices use thru-hole mechanical relays (not surface mount) and can be serviced using standard de-soldering tools simplifying repair and reducing down time. Our BRIC's integrated design ensures high matrix performance with high signal bandwidth and fewer system implementation errors.
-
Product
PXI Dual SP6T Multiplexer 2.5GHz 75, 1.6/5.6
40-785B-752
Multiplexer Module
The 40-785B-752 is a dual 75Ω 6-channel 2.5GHz unterminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI 4x3 10GHz Matrix
40-787-518-4X3
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
Product
PXI 10A Power MUX, 2-Bank, 16-Channel
40-661-003
Multiplexer Module
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
VME Generic Carrier Card For Conduction Cooled PMC(PCIbus Mezzanine Card) Modules
AVC-2-CC
-
VME64x (6U) generic carrier card for conduction cooled PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM conduction cooled PMC module for ARINC429, MIL-STD-1553 or any conduction cooled 3rd party PMC module.
-
Product
PXI 8 Slot BRIC 552x8 1-Pole (12 sub-cards)
40-560A-121-552X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Solid-State SPST Switch, 6-Channel 25A 100V
40-184-001
SPST Switch
This range of PXI high power switches support 6-off high current SPST switches into two PXI slots or 3-off high current SPST switches into one PXI slot. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each PXI solid-state SPST switch can support 25A of continuous current and switch up to 100V signals. The switch can sustain inrush currents of up to 90A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI - Test System
-
We provide a complete PXI test system made by PXI individual components: 19'' rack, Measuring and stimuli cards, Relay cards, Power Supplies, Integration additional protocol cards such as CAN and CANopen, Boundary Scan, Integration of additional test hardware
-
Product
PXI 3A Power MUX BRIC, 18-Channel, 16-Pole
40-571-206
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI 8 Slot BRIC 176x4 2-Pole (4 sub-cards)
40-562A-122-176X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-036-HI
Programmable Resistor Module
The 40-230-036-HI (PXI) and 42-230-036-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 395kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 2Ω to 52.4kΩ
40-253-033
Programmable Resistor Module
The 40-253-033 is a programmable resistor module with 1 channel which can be set between 2Ω and 54.4kΩ with 1Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Express PMC Carrier
TPCE260
-
The TPCE260 is a standard height PCI Express Revision 1.1 compatible module that provides one slot for a single-width PMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control.
-
Product
XMC Module Carrier PCI Express x 8
SK4-WALTZ
-
SK4-WALTZ is a bidirectional 8-lane PCI Express® Gen3 redriver, for optimum high speed signal integrity, and should be installed into a fat pipe peripheral slot of a CompactPCI® Serial backplane.
-
Product
PXI High Density Multiplexer, 4-Bank, 16-Channel, 1-Pole
40-610A-010
Multiplexer Module
The 40-610A-010 is a 4-bank, 16-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI High Density MUX BRIC, 4-Chan, 40-Pole
40-570-211
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
8-Slot BRIC, 64x16, 1Pole, PXI Matrix (2 Sub-cards)
40-559-801-64x16
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI Single 66x8 Matrix, 1-Pole
40-541-021
Matrix Switch Module
The highest density single slot PXI reed relay matrix module on the market today. This range also includes a 132x4 and 33x16 reed relay matrices with 1-pole switching. They are constructed using high reliability sputtered ruthenium reed relays, offering >10e9 operations to give maximum switching confidence with long life and stable contact resistance. Typical applications include signal routing in Functional ATE and data acquisition systems.
-
Product
PXI 8 Slot BRIC 75x4 2A 1-Pole Matrix
40-568-101
Matrix Switch Module
The 40-568 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 200VDC/140VAC. The 40-568 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI Precision Resistor Module 18-Channel, 1 to 31.5
40-297-010
Programmable Resistor Module
This PXI precision resistor provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI RTD Simulator Module, 8 Channel, PT500
40-263-402
Simulator
The 40-263-402 is an 8-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI 10 Banks of 8 Channel 2 Pole MUX
40-615-022-10/8/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 350
40-265-014
Simulator
This module simulates the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems.
-
Product
PXI 12-Slot BRIC Matrix, 110x16 1-Pole (10 sub-cards)
40-562B-321-110X16
Matrix Switch Module
The 40-562B-321-110X16 is a high density BRIC12 matrix module with a size of 110x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
