Multifunction I/O
See Also: Mass Interconnect
-
product
Multifunctional Meter
CPM-12
CPM-12 multifunction power meter provide high accuracy single phase and three-phase measuring and displaying, energy accumulating, power quality analysis, and data communication.Hardware can be option a a RS485 Modbus communication port.Auto wiring change (Note) via softwareCE and FCC approved
-
product
Programmable Multifunction Counter Board, Isolated, w/ 4 Function Modules & BISS-Master Logic
CPCI-1710-10K20
The board CPCI-1710 is a fast multifunction and multichannel counter board for the CompactPCI bus. The strengths of this board are its wide range of applications and high precision and reliability for though industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provides the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied sofware. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed or reconfigured as further requirements arise.
-
product
Multifunction Instrument
COMBI521EV
COMBI521EV is the new HT instrument to perform verification and control of electric car charging stations (EVSE) safety according to IEC / EN 61851-1 and IEC / EN60364-7-722 standards. Being a combined verification instrument, COMBI521EV also carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
product
CAMAC Multifunctional Logic Unit
CMDGG8
The CMDGG-8 is a multi functional FPGA based delay, logic and timing module which provide often needed functions such as gate, delay & pulse generator, logic fan in / fan out, coincidence register and scaler / pre-scaler.
-
product
16-Channel 500kSa/s USB Modular Multifunction Data Acquisition
U2353A
The U2353A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2353A to simulate simultaneous analog input acquisition.
-
product
Enhanced 16 Differential I/O Multi-Mode Transceiver Channels
DF2
Function module DF2 (Enhanced Version) multi-mode transceivers with 16 programmable I/O channels. Differential transceivers increase resistance to noise by creating two complementary signals. These complementary signals produced on balanced lines double noise immunity by creating lower power requirements due to lower supply voltages.
-
product
Multifunctional Immunity Test System For Automotive Electronics
EMS-ISO7637
EMS-ISO7637 automotive multifunctional immunity test system meet newest ISO7637-2 requirement of
. This standard was issued by international organization for standardization, and this system included all of ISO-7637 required test waveform and meet most of automotive manufacturer’s requirement for automotive electronic immunity test. -
product
16 Bit PXI I/O Board With 32 Or 64 Analog Outputs
CP266
The CP266 is a single-width, 6U, CompactPCI module with 32 or 64, 16-bit analog output channels. These independent analog channels provide ±10 V full-scale outputs. The channel update rate is 2ms, and each output is accurate to ±1mV. The power-up state of the analog outputs can be set to independent user-defined values. Paired output signals are provided to eliminate ground offset effects. The analog outputs are available at a single 68-pin SCSI II shielded connector (32-channel option) or a pair of 68-pin SCSI II shielded connectors (64-channel option).
-
product
Analog I/O Module with 16 single-ended analog output channels
IO111
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 16 output channel has its dedicated D/A converter with an update time of 3µs. The output coupling of the module is single-ended for all channels. The output range of each channel can be selected individually.
-
product
RCONAF-EC
A 6”cable transitions from the card edge connector on the RAF-EC-2P (champ 36) to one male HD-15 connector and two shielded RJ-45 connectors.
-
product
FPGA Workbench and I/O Cards
FPGA Workbench software provides a complete development environment for building customized solutions based on Concurrent’s programmable FPGA cards. FPGA Workbench includes a powerful GUI for selecting and configuring a wide range of pre-developed data acquisition and industry-specific modules to meet your application requirements. The library of functional IP modules includes pulse width modulation, analog I/O, digital I/O, SENT protocol, encoder, ignition, injection, crank/cam shaft, wheel speed sensor and change-of-state.
-
product
Low-Cost 16-Bit Multi-Function DAQ Card with 2-CH Encoder Input
PCI-9221
The ADLINK PCI-9221 is a 16-bit high-resolution and low-cost multi-function DAQ card, with 16-CH singleended or 8-CH differential input capable of up to 250 kS/s sampling rate. In addition, the PCI-9221 comes with a 2-CH 16-bit static analog output and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, general-purpose timer/counter, encoder input, and PWM output. The flexible function I/O makes the PCI-9221 the best single-board solution for combined data acquisition and simple motion control functionalities. Ideal for manufacturing, laboratory research, and factory automation, the PCI-9221 comes with all the functions you need at an affordable price.
-
product
6-1000V AC/DC Multi-function Voltage Tester
7340
Peaceful Thriving Enterprise Co Ltd
1. AC / DC Polarity Measurement2. Voltage Measurement3. High Voltage Indication4. Phase Rotation Test5. Non-contact Voltage Sensing6. Continuity Test7. Illumination
-
product
IoT I/O Gateways
ADAM-6700 Node-RED
Intelligent IoT I/O gateways with Node-RED analog, digital, or relay I/O connect edge to Azure cloud, SQL through MQTT, SNMP, RESTful, 3G, and WiFi.
-
product
Multi-function GPS/GLONASS Research Receiver
R100
The Multi-function GPS/GLONASS Research Receiver sets the standard in precision and versatility for GPS/GLONASS research. It provides highly accurate navigation, ionospheric measurement, time transfer, satellite monitoring and differential reference station capabilities. When combined with the temperature stabilized antenna it eliminates delay variations due to outside temperature, affording even greater accuracy.
-
product
Multifunction Voltage Tester
*Detects AC voltage by non-contact method: 70VAC to 250VAC*Finds broken wire location*Wrong connection check*Ground / Earthing disconnection check*Detects static radiation of TV / monitor*Checks operating condition of ionizer*Microwave leakage detection: ≥5mw/cm2
-
product
Ethernet I/O Products
Our products are designed to cover the most common industry applications. Our full selection of analog, digital, and serial I/O products with Ethernet connectivity allows for easy, simple to use data acquisition and control. Configure an IP-address and quickly acquire and output data over your network.
-
product
Terminal Block For 34950A 64-Bit Digital I/O
34950T
Use to easily connect discrete wiring to a terminal block for the Keysight L4450A 64-bit digital I/O.
-
product
16-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-16
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
PCI Multi-Functions Board
PCI-DSP-6713-MFIO
The board consists of private SDRAM and dual-ported SRAM attached to the DSP. An FPGA provides the timing and control as well as I/O drive for the 48 programmable I/O pins. Peripherals include a serial port and an USB port. Flash memory is available for downloading programs into a non-volatile memory. 16 channels of A/D and 16 channels of D/A provide analog interfaces to real-world signals
-
product
32-CH Separate I/O Terminal Base
HSL-TB32-MD
The HSL-TB32-MD discrete I/O terminal bases provide reliable and convenient wiring for HSL-M series products. The separate connection can make it easy to wiring, and the separate fuse can protect each I/O point. This low cost terminal base is particularly useful for users who need convenient way to construct their own signal ?Vcondition arrangement.
-
product
Rear-Panel I/O Transition Module
CP3-GESW8-TM8
CP3-GESW8-TM8 is a rear-panel I/O transition module providing flexible access to CP3-GESW8 or NETernity™ CP3-GESW8N rear-panel I/O. Up to eight Gigabit Ethernet ports of the switch are accessible from the transition module's stacked RJ-45 connectors. Each Ethernet port is routed as four 100 Ohm differential pairs.
-
product
24 TTL Channels, Enhanced, Programmable I/O
TL2
Function module TL2 provides 24 channels of TTL/CMOS transceiver functionality as either inputs or outputs. The transistor-transistor logic (TTL) employs transmitters with multiple emitters in gates having more than one input. TTL offers high switching speed and relative immunity to noisy systems. CMOS sensors provide image sensing technology by converting light waves into signals that are small bursts of current. These waves can be light or other electromagnetic radiation.
-
product
Terminal Block For 34952A And L4452A Multifunction
34952T
The Keysight 34952T is a terminal block for the 34952A and L4452A Multifunction with 32-bit DIO, 2-ch D/A and Totalizer. This terminal block is used for discrete wiring. It supports up to 20 AWG wire size typical for <100 connections or 24 AWG for >100 connections. The 34952T is a detachable terminal block with screw-type connections that provides a flexible method for connecting external wiring.
-
product
Enhanced 24 Discrete I/O Channels (0 to 60 VDC, 500 mA/Ch.)
DT4
The DT4 module (the enhanced version) features 24 programmable channels for either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3 – 60 VCC source. These modules can sense broken input connections and whether an input is shorted to +VCC or to ground. Additional features of the DT4 (Enhanced Version) are listed below.
-
product
16-CH 12/16-Bit 100 kS/s Low-Cost Multi-Function DAQ Cards
PCI-9111 Series
ADLINK PCI-9111 series are 16-CH, 100 kS/s low cost multi-function DAQ card. The PCI-9111 series feature flexible configurations on analog inputs. A RC filter is implemented on each A/D input channel for user to attenuate or filter input signal. The PCI-9111 series provide analog inputs with 5 programmable input ranges for bipolar inputs. The PCI-9111 series also support automatic analog input scanning. PCI-9111DG provides 12-bit A/D resolution while PCI-9111HR provides 16-bit A/D resolution. The PCI-9111 series also feature 1-CH 12-bit analog output, 16-CH TTL digital inputs and 16-CH TTL digital outputs. ADLINK PCI-9111 series deliver cost-effective and reliable data acquisition capabilities, and is ideal for a broad variety of applications.
-
product
12-Channel VME Current Loop/Process Control I/O Module
V220
The V220 is ideal for driving and sensing transducers in computer or PLC-based control systems. It can also be used to simulate complex industrial processes to control systems under development and certification.
-
product
LED Audio Spectrum For IOS
LED Audio Spectrum uses your iPhone or iPad microphone to visualize sound through fluid, colorful graphics that bounce to the beat! Now you can actually "see" any surrounding sound such as speech, music, singing and more. The app comes with a handful of simple, yet outstandingly implemented visualizers and each has multiple color themes to choose from. The built-in TV out support gives you the big picture!
-
product
VELOCICALC Multi-Function Ventilation Meter
9565-P
The portable, handheld VELOCICALC® Multi-Function Ventilation Meter 9565-P features a menu-driven user interface for easy operation in your local language. On-screen prompts and step-by-step instructions guide the user through instrument setup, operation, and field calibration. The 9565-P also features an ergonomic, overmolded case design with probe holder and a keypad lockout to prevent tampering during unattended use. The 9565-P model has a differential pressure sensor and does not include a probe.
-
product
12-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-8
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
