Multifunction I/O
See Also: Mass Interconnect
-
product
PMC Digital IO Board
MS 1815
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*128 channel digital I/O signal*Input/output ON state=3.5V to 5.0 max at -24mA*Input/output OFF state= 0.8max at 24mA*16 groups of 8 channels can be programmed as input/output*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
-
product
Multifunction Electrical Installations Meter
MPI-520S
The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.
-
product
ATCA I/O Rear Transition Module (RTM)
ART001
The ART001 is an I/O expansion ATCA Rear Transition Module (ARTM) that provides GbE, 10 GbE, PCIe and Management I/O for the front blade. The module is designed to mate with any ATCA Carrier. ART001 provides PCIe x8 access via an iPASS connector to the rear. The GbE rear access is provided via six SFP ports and five RJ-45 ports. The module has dual 10 GbE PHY which mates to the host via the zone 3 connector and provides dual SFP+ to the rear.
-
product
12-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-8
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
OPC UA Ethernet I/O Modules
ADAM-6300
Industrial OPC UA Ethernet I/O Modules with Modbus protocol converge OT/IT with security, linking to SCADA and the cloud for remote monitoring.
-
product
CB-37F-LP Unshielded, I/O Connector Block with 37-pin D-Sub
779353-01
37-Pin, Female D-SUB to 40-Pin, Female Screw Terminal, Desktop Mount Terminal Block - The CB-37F-LP is an unshielded terminal block that provides access to DAQ devices with 37-pin connectors. The 37-pin, D-SUB connector makes this connector block ideal for direct mounting on the … DAQ device or connecting through a cable.
-
product
PoE Ethernet I/O Module w/ 3-axis Encoder/Counter Inputs
PET-7083
A great device, that works well for building automation, factory, and machine automation, remote maintenance, testing, and diagnosis, the PET-7083 is a 3-axis high speed encoder/counter module. Its each axis can be individually configured for Quadrant, Pulse/Direction or CW/CCW counting modes. The maximum input rate for Quadrant counting mode is 1 MHz, and for Pulse/Direction, CW/CCW counting modes is 4 MHz. The encoder/counter module is equipped a FRAM to retain the counter value after it is powered off. FRAM is a nonvolatile memory that can hold written data even after it is powered off. The data retention can be 10 years. And the feature can be configured as enabled or disabled.
-
product
IoT Ethernet I/O Modules
ADAM-6000/6200
Supporting Modbus & IoT protocols, Ethernet remote data acquisition modules offer analog, RTD, thermocouple, digital, relay and counter I/O.
-
product
PCIe-Mini -IO Controller
PCie-Mini-CAN-USB
The PCIe-Mini -CAN board is engineered around the NXP LPC2387 microcontroller.This highly integrated 32 bits microcontroller based on the ARM7TDMI-S processor, has a very low power consumption and features 512 kB of on-chip high-speed flash memory.
-
product
Safety Certified I/O Modules
HY-TTC 30XSH
HY-TTC 30XSH, a member of the HY-TTC 30X family, is certified by TÜV Nord according to the EN 13849 standard and fulfills Performance Level c (PL c) requirements. Just as the other family members this certified unit must be used in combination with a master module. For safe communication the standardized CANopen Safety protocol is applicable since compliance to the European standard EN 50325-5 for CANopen Safety is provided.
-
product
REM-11100, 2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O
784748-01
2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O - The REM‑11100 is a voltage input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11100 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. This module features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling.
-
-
product
16-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-16
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
USB-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, USB Digital I/O Device
779975-01
The USB-6509 is an industrial, bus-powered USB device that can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is … required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the USB-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Multifunction Power Meter
Chongqing Blue Jay Electronic Co., Ltd.
Power Supply Voltage: Rated 220V (optional 57.7V/100V/380V) Current: Rated 5A (optional 1A) Frequency :45-65Hz 2. Load Voltage: 0.5VA / phase (rated 220V) Current: 0.5VA / phase (rated 5A) 3. Overload Current: 2 times rated continuous; 10
-
product
AdvintRIO™ Reconfigurable I/O
PIRANHA
The Piranha platform employs a NI single board RIO (sbRIO), NI C Series I/O modules, and custom circuitry. Piranha systems are not dependent on a separate host computer. They offer both Ethernet, and Wi-Fi connectivity to a powerful real-time controller and high performance field-programmable gate array (FPGA) and up to two (2) C Series I/O modules. It provides stand-alone embedded execution for deterministic LabVIEW Real-Time applications. These controllers are designed for ruggedness, reliability, and low power consumption. The heart of Piranha system is the reconfigurable I/O (RIO) FPGA core. The RIO core has an individual connection to each I/O module and is programmed using easy to use elemental I/O functions to read or write signal information from each module. Multiple units can also be daisy changed together for larger applications.
-
product
Digital Reconfigurable I/O Device
The Digital Reconfigurable I/O (RIO) Device features user-programmable FPGA for onboard processing and flexible I/O operation. You have complete control over the synchronization and timing of all signals and operations along with custom onboard decision-making that executes with hardware-timed speed and reliability. You can configure user-defined hardware for a wide variety of applications, such as custom digital DAQ, high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, custom digital communications protocols, bit error rate testing, and other applications that require precise timing and control.
-
product
Configurable CAN FD Modules With A Focus On Digital I/Os
PCAN MicroMod FD Digital 1&2
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The main boards PCAN-MicroMod FD Digital 1 and 2 focus on digital inputs and outputs, which are provided with the appropriate protective circuit. The digital outputs of Digital 1 are equipped with low-side switches and those of Digital 2 with high-side switches.
-
product
Multifunction Meter for Electrical Installations
AMPI-525
*Short circuit loop measurement:*Impedance measurement with 23 A (44 A phase-to-phase), short circuit resistance RZW =10Ω*Measuring range: 95...440V, frequency 45...65 Hz*Short circuit loop measurement with resolution 0,01 Ω , without tripping the differential protections (I∆n ≥30mA)*Automatic short-circuit calculation, phase-neutral and phase-phase voltage detection
-
product
FPGA Digital IO XMC
XF07-523
Curtiss-Wright Defense Solutions
The XF07-523 is a rugged Kintex-7 FPGA based XMC with digital IO. The combination of direct high-speed I/O ports and FPGA processing makes the XF07-523 ideal for demanding applications including radar, imaging and test equipment across commercial and defense market spaces. The XMC form-factor is ideal to SWaP constrained platforms such as UAVs and fighter aircraft.
-
product
MultiFunction Calibration
Omega offers a large selection of configurable Multi-Channel Meters that accept a wide variety of input signals for scanning, displaying, and logging measured data from multiple sensors.
-
product
Digital I/O Boards
Cable Transfer speeds up to 400 mb/per second Large FPGA provides for flexable cable interface
-
product
Analog I/O module with a higher analog input channel count of 64/32
IO105
Fast 16-bit analog module with 64/32 multiplexed analog input channels. This I/O module offers sampling/conversion times similar to the IO102 and IO103 but comes with a higher analog input channel count of 64/32. Analog outputs and digital I/O are not available on this module.
-
product
Advanced Programmable IO Board
MS 1508
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
product
Multifunction Counter (Pulse Input)
CM1-CT
CM1-CT multifunction counter(position) display controller, is design to have 2 pulse input, for proximity switch, photoelectric sensor, encoder etc.. Counting increase or decrease, positioning batch count etc.. display, with External input and Modbus communication port.Multiple types of input mode, trip mode setting to fulfil easy usage and requirement for counter controller. For different requirement, the meter can be with 2 relay or 1 Analogue output or 1 RS485(Modbus RTD mode) communication. (Choose 1 kind of output from the 3 options)
-
product
I/O Modules
Curtiss-Wright Defense Solutions
Finding I/O modules to integrate into your real-time, mission-critical systems can be difficult. You need fast and reliable movement of information between the various elements in your interconnected system. Your programs are long-term and need assured long-term availability.
-
product
Analog I/O Interfaces
United Electronic Industries, Inc.
24 differential analog input channels Maximum sampling rate of 1000 Hz per channel 18-bit resolution ±3 µA accuracy 350 Vrms Isolation Dynamic autozero support Embedded averaging engine
-
product
Multi-Function Power Transducer
TD2418B
The TD2418B is a micro-process based transducer with a 16 bits CPU (Center process unit) and equipped with full-digitized measuring, calibrating and output functions.TD2418B not only can take the place of several static con-verters and measuring instruments (V, A, W, PF, VAR, WH, VARH, Hz) by single unit, but also have some special function such as Maximum measuring, Minimum measuring and comparator output. In communication, we use the most convenient and the easiest RS232 or RS485 as our standard output port, besides, we adopt Modbus Protocol, one of the most popular protocol in the world, as our standard protocol.
-
product
Ethernet I/O Products
Our products are designed to cover the most common industry applications. Our full selection of analog, digital, and serial I/O products with Ethernet connectivity allows for easy, simple to use data acquisition and control. Configure an IP-address and quickly acquire and output data over your network.
