Simulation Software
computer programs that emulate the function of a system, predict expected performance, evaluate the impact, and assess design alternatives.
See Also: Simulation, Simulators, Simulation Testing, SPICE, Predictive Analysis
-
Product
Force Data Acquisition Software
-
SW-1X data acquisition software is for force gauges with RS-232 output.SW-2X data acquisition software is for collecting force and displacement data from RS-232 output force gauges, with a -s test stand.Force Recorder data acquisition software is for ZTS & ZTA force gauges with USB output. Force Recorder Pro collects both force and displacement data with ZTA gauge and FA test stand.
-
Product
EMI64k Automation Software Suite
-
The EMI receiver families TDEMI® of GAUSS INSTRUMENTS® provide a huge fully CISPR compliant real-time bandwidth and therefore allow to speed up your measurements tremendously and to reduce the measurement uncertainty significantly - both at the same time. By using the full automation software suite EMI64k from GAUSS INSTRUMENTS the test procedures according to the CISPR 16-2-3 standard for the FFT-based measuring instruments as well as conventional testing (pre-scan and final maximization) and further EMC Standards are available. In comparison to the previously conventional pre-scan and final measurement strategy, the overall test quality can be significantly increased whereas the testing times are reduced by orders of magnitudes.
-
Product
WAN Simulator / Emulator
LANforge ICE
-
LANforge ICE emulates networks that involve limited bandwidth, latency, packet loss, and corruption. LANforge ICE tests the behaviour of devices that sit on either side of an impaired network. Reduces lab and training costs by replacing expensive WAN hardware, such as T1 and FrameRelay devices. Automates testing with various scripting features and libraries.
-
Product
Laureate Datalogging Software
-
Laurel's data logging software can turn a PC connected to up to Laureate instruments into a powerful, data logging system. The Laureates can be any mix of digital panel meters, counters, timers and transmitters. The software allows 31 hardware instruments and 33 virtual instruments. The latter can display calculated parameters which combine data from multiple instruments.
-
Product
Software
Driver Module
-
Consistent Driver module for various target Environments to perform Emission homologation, certification, RDE, range, customer FE tests with human drive styles for all kinds of cycles
-
Product
Chamber Simulator System
BroadSim Anechoic
-
Built on our proven BroadSim platform, BroadSim Anechoic allows users to accurately simulate real-world GNSS environments in their Anechoic Chambers. BroadSim Anechoic has 32 individual RF outputs enabling the system to drive 16 dual-frequency antennas. Revolutionary features like automatic antenna mapping, automatic time delay calibration, and automatic power loss calibration are what make BroadSim Anechoic the most advanced Anechoic Chamber simulator on the market today.
-
Product
Torque Data Acquisition Software
-
SW-1SV-USB data acquisition software is for all Cedar torque instruments.Force Recorder is compatible with the new HTGS & HTGA digital torque testers.
-
Product
3D Measurement Software
PowerInspect®
-
3D measurement software for a range of hardware.PowerInspect software makes inspecting complex free-form surfaces simple, across all your inspection hardware. Use the right tools for the job, with one interface on all devices.
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
-
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Regenerative Grid Simulators 9kVA-15kVA
-
Chroma Systems Solutions, Inc.
Four quadrant, single- or three-phase AC power sources designed to simulate real-world grid characteristics for EV, PV inverter, and smart-grid test applications.
-
Product
Advanced Chemometrics Software
PLS_Toolbox
-
PLS_Toolbox is a collection of essential and advanced chemometric routines that work within the MATLAB® computational environment. It contains the tools that chemical engineers, analytical chemists and other scientists require to explore their data and build predictive models. Even less experienced users can perform powerful analyses with interactive state-of-the-art tools. PLS_Toolbox incorporates the most advanced suite of multi-way tools available in the world as well as a vast array of other functions.
-
-
Product
Vibration Analysis Software For Squeak & Rattle Testing
MB BSR Suite
-
MB BSR SUITE is the complete solution for all measurement tasks in the field of NVH, Squeak & Rattle and Sound Quality testing. Comprehensive analysis and assessment capabilities also enable the use of the BSR Suite for analysis and evaluation of functional and operating noise, vibrational effects on humans as well as the acoustic and haptic feedback of controls and actuators. Predefined test configurations for typical tasks such as multi-channel road load data acquisition, drive-file generation and objective Squeak & Rattle and Sound Quality testing allow for fast and simple operation. Signal statistics and user defined thresholds or reference-curves can be used for objective evaluation of different acoustic or haptic quality criteria. In addition the development and integration of application- or customer-specific analyses and evaluation methods is also possible at any time. Contact MB to find a solution for your measurement task!
-
Product
Signal Generator Software
-
The software solutions for the class-leading signal generators from Rohde & Schwarz support various demanding applications. These include powerful radar simulation, the generation of digital I/Q signals supporting various radio standards as well as software tailored for multi-channel vector signal generator setups.
-
Product
Software
Dielectric Constant
-
Materials Development Corporation
The Dielectric Constant option allows the user to measure the dielectric constant of a wide range of materials. Simply input a test voltage (in accumulation), the area (or diameter), and stray capacitance to determine the relative dielectric constant.
-
Product
ReCalibration and Post Calibration Software
SI58
-
The SI58 software allows the user to set zero and span as well as do full temperature compensation and linearity corrections for your Validyne USB pressure transducer. The SI58 provides everything needed to change the range of your transducer and calibrate it through the new full scale pressure. Corrections to non-linearity and temperature error are also possible. The SI58 software provides prompts to the operator for temperature and pressure points to achieve an accurate calibration.
-
Product
USRP Software Defined Radio Stand-Alone Device
-
The USRP Software Defined Radio Stand-Alone Device consists of an onboard processor, FPGA, and RF front end. You can program this device using either LabVIEW Communications System Design Suite or an open-source software workflow, depending on the operating system you choose. You can provision the device with NI Linux Real-Time, Linux Fedora, or Linux Ubuntu real-time operating systems. The USRP Software Defined Radio Stand-Alone Device enables you to prototype a range of advanced research applications such as stand-alone LTE or 802.11 device emulation; Medium Access Control (MAC) algorithm development; multiple input, multiple output (MIMO); heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
2 Port BRI-S/T-U ISDN Simulator
BRI-2UST
-
The unit has two S/T and two U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Radio Link Simulator
RLS-2100
-
Square Peg Communications Inc.
It is the most comprehensive, with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full motion support and integrated GPS simulators. It is the most flexible, providing end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. It supports the highest bandwidth and has an intuitive, user-friendly interface. And it does it all in one box.
-
Product
PDS Cutter Dredger Monitoring Software
-
TELEDYNE PDS for Cutter Dredges is designed to the requirements of the dredge operator to carry out their job more efficiently. The operator has a real time overview of the dredger with the top and side views displaying the vessel outline, ladder, and cutter head along with the surveyed depths, design, and dredged depth.
-
Product
ARINC 429 Test And Simulation PXI Module
PXI-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
-
Product
Software Platform for Control Systems
Titanium Control
-
Wind River introduces software platform that enables critical infrastructure companies to cost-effectively evolve aging legacy control systems not previously designed to support IoT. Based on open standards, Wind River Titanium Control on-premise cloud-scale infrastructure virtualizes traditional physical subsystems enabling control systems. With addition of platform to product portfolio, company drives new industrial era through virtualization, real-time performance and edge-to-cloud connectivity.
-
Product
Unified Remote Device Management Software
DeviceOn
-
Advantech Service-IoT software provides a wide variety of IoT solutions to facilitate devices management from hardware, software to peripherals.
-
Product
Software Tool Especially Designed for Production Process Supervision
LEON OP
-
The Leon OP is a software tool especially designed for production process supervision. Therefore, the application provides the following key features:- Execution of KT ICT sequences or NI TestStand sequences- Parallel, semi-parallel or sequential execution of test sequences, individually definable per Test Sequence- Customizable User Interface, simple or detailed test views, grid or board layout arrangement possibilities- Tracing into sequence execution- User management with different user levels and restrictions per user group- Displaying execution results and statistics by panel or nest- Supporting interaction with an automation (e.g.: handler system)- Supporting interaction with a process control / MES system- Integrated Callback structure to adopt to different workflows- Maintenance view for fast displaying of fails inside a board- Result History View to quickly access the last test results- Store execution results in result files with user defined format- Autostart-option for running application in automation mode without any operator interaction at all- Several abortion criteria to abort execution by fail count (consecutive or time based)- A Maintenance View for viewing testprobe locations on the DUT is available via Aster Quadview
-
Product
Hot Dipping Simulator
HDPS
-
This is a hot-dip galvanizing simulator that simulates various hot-dip galvanizing processes such as heating, cooling, vacuuming, gas replacement, and spraying of steel sheets on a laboratory scale. It is possible to simulate the parameters close to the actual line, such as zinc bath temperature, immersion speed, immersion time, and gas flow rate adjustment for weight control. Also, 20 to 25 sheets can be tested
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, Simplified Current Sink, 750 V Isolation
41-752A-903
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
CAD/CAM Software
C-LINK DTM
-
C-LINK DTM is the interface between CAD, test and repair, and combines these into one platform. Our CAD/CAM software has since its introduction in 1985 developed into the leading standard tool. C-LINK supports virtually every test system on the market.
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for PXI Express
PXIe-DCE
-
Avionics Interface Technologies
Supports 10/100/1000 Mbit/s Full Duplex EthernetUtilizes SFPs to support both Copper and Optical interfacesUser controlled Ethernet frame transmissions with high precision timing and scheduling
-
Product
3D Software
Geomagic Design X
-
Geomagic Design X is an all-round, professional reverse engineering software with a smart combination of history-based CAD with 3D scan data processing, letting you produce feature-based, editable solid models compatible with your existing CAD software.
