System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
product
For Dielectric Oil Test
Stoil Cell
The option allows the testing of the insulation characteristics of the oil by checking if there is no contamination.
-
product
Test Extender
PMC
The PMC test extender provides an active interface between a PMC carrier slot (PCI bus) and a PCI Mezzanine Card (PMC).
-
product
F9 Systems CalBlade
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
product
Acoustic Measurement Systems
Even AuSIM's audio simulation is only as good as the model parameters within the simulation. For AuSIM, deriving optimal model parameters begins with studying the acoustic world around us. The AuSIM3Dtm display systems synthesize a virtual aural environment from parameters based on the physical world. But the same techniques can be applied to reverse the process and extract parameters from the physical world to use for later synthesis.
-
product
Video Test Generator
802BT
The 802BT is our multi-media video signal generator for testing CRTs, flat panels, projectors and TVs including HDTV. The 802BT is optimal for DTV, digital and analog displays and allows production and engineering users to create the most complex test images. You get the flexibility required to meet a tough production budget with the wide range of outputs the 802BT offers. And a PCMCIA slot makes it easy to copy one generator to another.
-
product
S-parameter Measurement System
DPS21
Unlike a coaxial tube type or a wave guide tube type, this method does not make errors caused by air-gap as specimens are not put into a fixture. Practical data can be obtained even at the rough, uneven surfaces where the specimen is placed on.It enables compactness and measuring specimens by plane wave because of direct installment of lens with an antenna.It enables measurement by monitoring S21 and S11 parameter with connections of a test fixture to a vector network analyzer and PC.
-
product
Video Test Generator
701A
If you’re testing digital or analog computer monitors, video projectors, multimedia monitors, or TVs, the 701A Video Test Generators provides the signals, test patterns, and audio to do your job, easily and accurately. Field technicians and factory people on the move will appreciate the convenience of battery power and small size. The 701A Video Test Generator is designed to go where you go.
-
product
IIoT & Wireless Systems
Omega has IIoT products that allows sensor connectivity up to the cloud to view data from anywhere in the world. With a variety of smart sensors and gateways you can build your IIoT system today.
-
product
Fanless Embedded System
Axiomtek offers a full range of expandable, low power consumption/high performance vertical market targeted embedded systems (eBOX). The embedded systems are designed to operate reliably within mission critical environments. The embedded PCs are tailored to meet all your needs with useful features including powerful computing capabilities, fanless operation, wide operating temperature ranges, low power consumption, superior reliability, flexible I/O configurations, and long product life cycles and support.
-
product
Food Monitoring Systems
Is a system of repeated examination, measurement and evaluation of levels of undesirable substances, such as plant protection products, heavy metals and other contaminants, in and on food.
-
product
Motor Protection System
SR469
The SR469 Motor Protection System, a member of the SR family of relays, provides protection, control, simplified configuration and advanced communications in a cost effective industry leading draw-out construction. Designed for medium voltage motors, the 469 delivers advanced protection with customizable overload curves and single CT differential protection for added flexibility.
-
product
RF Test Probes
With over 50 Tip-Styles, you can be certain we can help you find the right solution for your testing demands. And if we don’t offer a probe solution already in production, we will work together with you to develop a custom solution.
-
product
Design and Development: Complete Systems and System Components
Custom Systems Integration Inc.
CSI''s design and development (D&D) organization has the resources, skill and experience to design a complete turnkey system, a system component or collaborate with customer''s internal staff on any part of a system.
-
product
C-Mic Testing System
BK3010
The BaKo BK3010 is our main C-Mic tester. It's small enough to carry under your arm and with a test time of under 0.5 seconds, it tests as fast as you can connect a microphone. Setting up the specifications is so easy and intuitive, we based the BK3012 D-Mic Tester on it. It is also the model for our BK9010B Fully Automatic C-mic Tester.
-
product
Sensortech Systems
IMPS-4400
The Instant Moisture Profiling System (IMPS) is a non-contact RF moisture profiling system, typically used in board manufacturing plants, built in a customizable multi-sensor arrayed framework.
-
product
Test Accelerometer Sensitivity And Noise Test
Accelerometer Test Unit
*Quick and Accurate Accelerometer Test*Battery operation*All tests use 32-bit resolution A to D Converter*All data downloaded to PC via Ethernet link*Records all data to a flexible easy to use database*Records time and date of tests
-
product
Multimedia Test Instrument
882EA-HDMI
The Teledyne LeCroy quantumdata 882EA-HDMI test instrument provides two (2) HDMI transmit (Output) ports and two (2) HDMI receive (Input) ports for testing both HDMI sources, sinks and repeater devices. The 882EA-HDMI instrument can optionally be equipped with the industry approved HDMI CEC and HDCP compliance test options as well.
-
product
Dynamic Jack System
This is a structural fatigue testing machine for researching the dynamic behavior of full-size or model structures by applying repeated loads. The actuator that supplies the loads to the specimens can be installed on load frames, reaction floors, reaction walls, etc.
-
product
In-Process Test OTDR
8000i
The 8000i In-Process Test OTDR is the most recent addition to Photon Kinetics' family of innovative solutions for optical fiber cable testing. The 8000i's "cable test optimization" provides the balance of OTDR dynamic range and dead zone performance that's proven to be most effective for accurate characterization of typical fiber cable lengths. Dynamic range has been maximized to reduce measurement time, while resolution has been tuned to ensure that typical cabled fiber defects are detected. Th...show more -
product
Measuring Systems For Night Vision Systems
MTF Master IIT
Optik Elektronik Gerätetechnik GmbH
Measuring system for MTF, SNR and EBI of Image Intensifier Tubes (IIT). The MTF MASTER IIT was specially developed to classify the quality of image intensifier tubes by the objective criteria of the MTF (Modulation Transfer Function).
-
product
Test Probes
Test Probes provide the vital link to transfer measurement signals as true and as undistorted as possible. Therefore these elements can be regarded as the heart of Test Fixtures – and for this very reason it is important for Equip-Test to offer high performance Test Probes with best quality and value, and thus ensure maximized ROI (Return of Investment) for our customers. Test Probes supplied by Equip-Test always provide the best-possible available solution for your contacting demands.
-
product
Telecom Test Access
TAU 2
Networked Communication Solutions, LLC
Handheld T1/E1 trouble shooting tool provides the test access capability of a cross-connect panel (DSX), in a small, convenient, handheld package. It saves time often wasted while deciphering test connections on network equipment and simplifies the patch cable selection required for maintenance and installation.
-
product
Band-On Telemetry System
Advanced Telemetrics International
The ATi Band-On Telemetry System transmits real-time sensor data from a rotating shaft while the system is running. The system consists of one or more rotating signal conditioner/ transmitter modules with battery pack and a stationary receiver. Rotating transmitters are available to interface with most any type of sensor including strain gages, thermocouples, thermistors, RTDs and accelerometers.
-
product
Wafer Test Solutions
Wafer Test Solutions has established leadership positions in developing and deploying application-specific test solutions for MEMS devices, offering wafer and frame probing stations suitable for R&D, Wafer Sort, and Final Test. We offer state-of-the-art solutions to test environmental and motion sensors in wafer and other advanced packages.
-
product
Sand & Dust Test
This test method is divided into two procedures. The small particle procedure, using fine dust is performed to ascertain the ability of equipment to resist the effects of fine particles which may penetrate into cracks, crevices, bearings, and joints. The blowing sand test, using coarse particles, is performed to determine whether equipment can be stored and operated under blowing sand conditions without experiencing degradation of its performance, effectiveness, reliability, and maintainability due to the abrasion or clogging effect of large, sharp-edged particles.
-
product
Protocol Test Solutions
Reducing engineering development time, issue resolution cycles, and overall costs; increasing product quality, system reliability, and customer satisfaction.
-
product
Magnetic Measurement System
Model 110
The Model 110 Magnetic Measurement System is a very high field version of our industry-standard MESA, designed specifically to measure high-coercivity samples. It uses powerful amplifiers and specially designed water-cooled solenoid assemblies to achieve the magnetic fields required by state-of-the-art material.
-
product
Kelvin Test Contactor
ecoAmp
ecoAmp™ Kelvin test contactor has a durable monolithic pin design with low and stable contact resistance. It is a high-power cantilever kelvin contactor with a patented spring and tip design for optimum heat dissipation. This ensures best reliability, long spring life and high yield even under highest current and temperature requirements. Featuring extended Automotive temperature range -60 ̊C to +175 ̊C, capable to stand thermal stress during high-power test. The contact motion is decoupled from the test board.
-
product
Kelvin Contact Test
C.C.P. Contact Probes Co., LTD.
We offer different tip types for low resistance testing.
-
product
Test Data Organization
Filters enable you to organize your data in a dynamic rather than a static way. Using filters, you can organize your issues, tests, testSets, and requirements, based on their fields, and have the information, displayed in multiple ways. For example, you can create 2 filters in the Test library module - one that displays the tests that are related to the DB server and the other filter displaying tests whose priority is ‘Show Stopper’. A test that has its component field set on ‘DB server’ and its Priority set on ‘Show stopper’ will appear in both trees accordingly.
