ATE Fixtures
Holding and positioning assemblies to guide UUT I/O access by automated test equipment.
See Also: Test Fixtures, PCB Test Fixtures, Board Test Fixtures
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
Component Test Fixture For N1413 With B2980 Series
N1428A
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
product
Dielectric Material Test Fixture
16453A
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Bottom Electrode SMD Test Fixture
16198A
Designed for impedance evaluations of bottom electrode SMDs and supports 201 (mm) and 402 (mm) sizes
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
Parallel Electrode SMD Test Fixture
16192A
The 16192A test fixture is designed for impedance evaluations of side electrode SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1(L)[mm].
-
product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
product
Magnetic Material Test Fixture
16454A
The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.
-
product
Liquid Test Fixture
16452A
The 16452A provides accurate dielectric constant and impedance measurements of liquid materials. The 16452A employs the parallel plate method, which sandwiches the liquid material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixure.
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
Fixture Kit In-Line 6TL35 455x600mm
AH500
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 3000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
ATE
QT 200 NXG
Qmax Test Technologies Pvt. Ltd.
QT 200 Nxg a Highly sophisticated ATE, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
High Temperature Component Test Fixture
16194A
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
ATE Development
Aero Engineering Support Group
ATE Development Aero Engineering Support specializes in designs and manufacturing of a wide variety of Automatic Test Equipment (ATE) of support for military avionics, commercial avionics, industrial sector, etc. AESG is committed to providing industry leading equipment that are designed to be scalable and expandable ATE capable of providing reliable functional test solutions for any electronic assembly or Circuit Card Assembly. New from Aero Engineering Support is the A2500 system, providing:
-
product
Satellite ATE
MS 1123
Configurable Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out card level testing for satellite systems (12 different types of boards). The purpose of ATE is to provide a user-friendly environment to test the boards for their functionality, perform specific tests of each card. The card level testing facilitates troubleshooting down to a faulty signal flow path. Both hardware and software designed such a way that each Input / Output is configurable and user can dynamically script the test procedure using standard ‘C’ Language.
-
product
RFIC ATE System
RI 7100A
The RI 7100A, which RI has shipped for over 10 years, has proven itself as the most advanced, reliable (> 4500 hours MTBF) and cost effective RFIC ATE System available. "Our recipe for high performance microwave test has always been dependent on an extremely elegant RF signal path while maintaining the most advanced microwave calibration software," said RI President, Mark Roos.
-
product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
-
product
ATE For Data Communications Equipment
• Developed for DRS Codem Systems, Inc. to test the CTM-IP product line of the Multi-Interface Protocol Converter.• Manufacturing Test support for the CTM-IP chassis and Interface Modules. Functional test of signaling, protocol and software configurations for various communication interface configurations.• Regression Test support for Engineering Product Development. Configurable test sequencing allows engineer to select specific tests for execution, with the ability to exercise all combinations of data rates and interface configurations.
-
product
Compact Semiconductor ATE
QST286
Qmax Test Technologies Pvt. Ltd.
The Qmax Model QST286 is a compact small foot print, sophisticated automatic semiconductor tester. Its state-of-the-art hardware design which is freely configurable to user's application requirements and software features makes it ideal for high throughput production testing of wide range of low pin count medium power ICs as listed below but not limited to Optocouplers, Isolators, LEDs, Photo diodes, Photo transistors, Photo sensors, Photo detectors , Analog Mux , Relays and more.
-
product
ATE Development Services
Automated Testing Engineering and Automated Test Equipment (ATE) provide a faster, more efficient way to test your product. With the help of LabVIEW and Modular Instruments, our engineers create test and measurement systems for all areas of product design and manufacturing.Whether you are in early stage R&D prototype testing, and design validation, or providing a solution for quality control and life testing our engineers can work with you to design fully customized automated Test Systems using entirely off-the-shelf products to ensure you deliver quality product on time.
-
product
RWR ATE MKII
MS 1111
Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out LRU and card level testing for TARANG systems of all platforms. The purpose of ATE is to provide a user-friendly environment to test the LRUs and sub-systems (individually) for their functionality, perform specific tests of each LRU / sub-system and Card Level Testing. The card level testing facilitates troubleshooting down to a faulty signal flow path. The UUT tests are carried out by injection of the stimuli generated by the computer or the programmable test equipments and the responses from UUT / test equipments are feedback to the computer for evaluation and generation of reports.
-
product
ATE Test Systems
Introducing the Procyon ATE System! When it comes to ATE Test Systems for a for low- to high-volume production, Intepro has the testing power you require to be successful. For more than three decades, Intepro Systems has designed, built and integrated power supply test equipment for the world’s largest and smallest power supply manufacturers.
