Line Fault Indicators
See Also: Overhead Line
-
product
Indicators - Electronic
An electronic device used to read an input value from a measuring device and show a displayed value.
-
product
Tap Position Indicator
This instruments serves to indicate the angular or linear movement of any number of mechanism / Temperature at remote point particularly for OLTC panel to indicate - tap Position, winding / Oil Temperature Indicator.
-
product
Power Line Meter
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
product
Programmable Selsyn Indicators
PSI
Computer Conversions Corporation
Computer Conversions Solid State Selsyn/Resolver Indicator digitizes the outputs of Selsyns, Synchros and Resolvers for position indication and control applications. The Selsyn Indicator is designed to replace failure prone mechanical selsyn torque receivers, counters, etc. The tracking converters high noise immunity and high speed tracking characteristics make it ideal for use in industrial envrionments.
-
product
PXI Fault Insertion Insertion Switch Modules
Our PXI Fault Insertion Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect – all of which can simulate connectivity problems in the system.
-
product
Frequency, Rate Meter, Flow Rate Indicator
Two independent scalable pulse-input channels from 0 Hz to 1 MHz. Channels may be combined arithmetically. One channel can display total while other displays rate. High read rate for control applications: AC line frequency can be measured to 50.0000 or 60.0000 Hz in a few line cycles. Ideal for use as a tachometer or readout of a turbine flow meter.
-
product
Portable Hand Held Load Cell Indicator
MODEL SSI
The SSI is a Plug & Play Smart TEDS IEEE 1451.4 compliant portable handheld Load Cell Indicator. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SSI will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SSI can be set up by simple front panel push buttons. The SSI can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, inch pounds, etc. The SSI also has a Units key for automatic conversion of readings for load, torque and pressure. The SSI has an ultra-fast signal-sampling rate of 15,360 samples/second for true peak and/or valley testing capability. Auto-tare allows the meter to be set to zero for any input signal level. The SSI also features a USB port for data logging to a PC. You can also log data to the SSI’s internal memory storing up to 16,000 time and date stamped readings. The SSI also features 2 built-in solid-state alarm relays with LED and audible indicators. The SSI will operate up to 65 hours on a single charge or use the included battery charger for applications where the SSI is mounted permanently.
-
product
Cable Fault Point Identifier
OCFI
Shanghai Tarluz Telecom Tech Co., LTD
Optical Cable Fault Identifier (OCFI) is The latest instrument of optical cable maintenance, repair equipment developed by tarluz, it can identify the physical cable fault location easily. This is an essential tool for fiber optic cable repair!
-
product
Handheld Cable Fault Locator
TM800H
TM800H Handheld Cable Fault Locator adopts TDR (Time Domain Reflection), new signal process and data collection technology. It can locate the distance of cable break and mix faults accurately. TM800H can be widely used in the communication installation, maintenance and general wiring. It can troubleshoot not only the local Telco-cable, but also Network cable. Its high sampling rate makes the measurement dead zone as narrow as 1 meter. This makes it a straightforward, user-friendly test solution.
-
product
Test Line • Devices for measuring electrostatic charges
HAUG offers a wide selection of easy-to-use gauges. These are field charges with which electrical charges, fields and potential can be measured. The measured values show how strongly a surface is covered with an electrostatic charge.
-
product
Cable Sheath Fault Location
Locating cable sheath faults is one of the last steps in cable testing, occurring after you have identified the existence of a cable fault via the identification procedure based on your specific site variables and the type of system you are working on
-
product
Pen-type Visual Fault Locator (VFL)
JW3105A
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3105A VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes:
-
product
Cable Test And Fault Location Systems
Power outages can cause serious financial and social damage, as they disrupt the normal operation of security and life support systems, destabilise the operation of industrial facilities, transport network, and utilities. Reliable power distribution is ensured by an effective prevention and prompt elimination of cable faults and electrical equipment failures. KharkovEnergoPribor Ltd. offers a range of integrated solutions designed for testing power cables and electrical substation equipment, as well as locating various types of faults in underground utilities.
-
product
Stimulus Induced Fault Testing
SIFT
SIFT allows for the analysis of numerous stimuli to identify speed, fault, and parametric differences in silicon. The heart of the SIFT technique revolves around intentionally disturbing devices with external stimuli and comparing the test criteria to reference parts or timing/voltage sensitivities. Synchronous interfacing is possible to any tester without any wiring or program changes. The system can be based on either a motorized probe station or portable microscope stand for test head applications.
-
product
Visual Fault Locators
MVFL Series
Shanghai Tarluz Telecom Tech Co., LTD
MVFL series Visual Fault Locators is meet the Class IIIA product, which is the easiest way to identify fibers from end to end and locate polished connector endfaces. Its red laser shines through most yellow-jacketed fibers to help you pinpoint breaks, bends, faulty connectors, splices and other causes of signal loss. The 1mW output power enable the MVFL has a reach of up to 5 km. MVFL seires VFL locates faults visually by creating a bright red glow at the exact location of the fault on single mode (SM) or multimode (MM) fibers. Due to its small size, lightweight and simple but proven design, the MVFL can accompany you anywhere In your pocket or belt pouch in harsh environment
-
product
Weighing Indicator Series
Ningbo Yaheng Electronic Technology Co.,Ltd
YEAHEVER Weighing Indicator Series
-
product
Synchro and Resolver Angle Indicator
AIT5
Computer Conversions Corporation
This series of units were designed to satisfy Hi speed synchro/resolver applications where the output data must be fresh and no data staleness can be tolerated. The tranducers utilized are the same as in the regular MDS series, however different tracking electronics are used. The resultant data tracks the input shaft perfectly and is always fresh and accurate at input speeds up to 64 revolutions per second, depending on the resolution. Data in BCD or Binary formats are available, and clean, unambiguous crossovers are guaranteed.
-
product
Phase Sequence Indicator
Cambridge Instruments & Engineering Co.
Phase sequence indicator is a must for checking new electrical connections, installation and maintenance. It is useful in wiring of switchboards, when 3 phase watt meters and power factor meters are connected. In wiring 3 phase AC motors rotation can be checked and corrected if need be, by checking the sequence.
-
product
Phase Sequence Indicators (Contact Type)
ST-860
Standard Electric Works Co., Ltd
● Three functions in one unit: open phase, phase sequence and motor rotation indication. ● Large size alligator clips for easy clipping onto switch- boards terminals. ● Highly reliable. ● Identifies 3 phase sequence and open phase check.● Ideal for installing conveyor lines, pump systems and interconnected drivers.
-
product
Standard Tap Position Indicator
NMC,s Tap Position Indicator is a Microprocessor based specially designed instrument used to indicate the Tap Position of the Power Transformer with On Load Tap Changer.
-
product
3 GHz, 4 Channel Programmable Delay Line
QPADL3
The QPADL3 is a programmable delay line instrument with 4 independent channels designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 3 GHz.
-
product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
product
Ground Fault Locator
K-3837
Kongter Test & Measurement Co., Limited
Kongter’s K-3837 Ground Fault Locator is developed to fast detect, trace and pinpoint virtual grounding faults on LIVE DC systems with earth fault. It will save you from long time unnecessary troubleshooting and helps to increase the stability of your electrical equipments. It is widely used in various DC systems including power utilities, locomotive, telecom and etc.
-
product
Line Interactive UPS
LION PLUS SERIES 650 - 2000 VA
With its compact design line interactive Lion + Ups offers secured power protection and battery backup power during outages for computers, outers/modems, external storage devices, game consoles and other electronics in your home or business. Lion + secures your data and your equipment by protecting you against damaging surges and spikes.
-
product
3-Sensor R-G-B (Prism) Color Line Scan Cameras
JAI's advanced product offering includes a set of 3-sensor R-G-B color line scan cameras for industrial machine vision applications. Part of the Sweep+ Series, these cameras feature state-of-the-art prism technology providing the best possible performance, precision, and versatility for line scan imaging in continuous production flows.
-
product
Fault Injection Module
WF 3154 C-Series
The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel provide three solid state relays that can be used to create electrical fault conditions like: Open circuit, Short circuit to battery, Short circuit to ground.
-
product
Wafer Auto Line Integration
The line is used for semiconductor wafer grinding. It carries out material matching and distribution, automatic loading and unloading, auto focusing and positioning and many other functions. The grinding precision is 2μm(3-sigma). It is also capable of collecting and analyzing real-time production data and interfacing with MES system.
-
product
Multi-Function Transient Fault Recorder
TR-3000
The TR-3000 is the only tool you need to capture and diagnose power system anomalies. With multiple recording modes and continuous transient oscillography, you will never miss an event. The TR-3000 captures high speed transients and long term system disturbances with enough memory to give you a complete view of the system disturbance. The TR-3000 takes the place of several devices: • Fault and Disturbance Recorder • Transient Fault Location • Phasor Measurement Unit • Power Quality Monitor • Sequence of Events Recorder.
-
-
product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 4 Channel
40-200-004
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
