Line Fault Indicators
See Also: Overhead Line
-
Product
Analyzer for Safety Agency Production Line Testing
HypotULTRAIII
-
Ethernet Communication CardUSB/RS-232, GPIB & Printer InterfacesData Storage CardInterconnection to Modular Scanning MatrixOptional 10 Volt Analog InterfaceStorage of up to 50 setups with 30 steps per setupPatented SmartGFI® functionPatented prompt and hold functionPatented CAL-ALERT® functionPatented VERI-CHEK® functionReal Current measurementDual Continuity test modesBuilt-in security settingsLine and Load regulation
-
Product
Cable Fault Locator-TDR
TM800N
-
TM800N Cable Fault Locator (hereinafter to be referred as TM800N) is used for test est cable break, short circuit faults of telephone cable, data cable, high frequency cable, coaxial cable,and so on.
-
Product
Power Line Isolators & Conditioners
-
A power line conditioner (also known as a line conditioner or power line conditioner) is a device intended to improve the quality of the power that is delivered to electrical load equipment. While there is no official definition of a power conditioner, the term most often refers to a device that acts in one or more ways to deliver a voltage of the proper level and characteristics to enable load equipment to function properly.In a nutshell, poor incoming electrical power converted to good output power.
-
Product
AC Line Harmonics Analyzer Including Flicker Analysis With UK, Schuko Or US Socket.
HA1600A
-
Compliance quality measurements to EN61000-3-2 and EN61000-3-3Measures peak or rms voltage or current, real or apparent power, power factor, phase etc.Tabular/histogram of 40 harmonicsVoltage/current waveforms displaysContinuous analysis with real-time graphical updateWide range of power connectors available320 x 240 pixel high-contrast displayUSB, RS232 and printer interfaces fittedPC control and documentation software supplied (HA-PC-Link+)
-
Product
Automotive Battery Production Line Tester
-
The Production Line Tester (PLT) is typically installed at the end of battery production lines (finishing). An electrical load test after formation charging is essential to assure performance and quality. The energy discharged during this test must be minimized to eliminate the need for recharging after testing.
-
Product
5uH Line Impedance Stabilisation Network LISN - CISPR 25
TBOH01
-
The TBOH01 5H LISN is a device required to setup conducted noise measurements of DC-powered devices. It is designed to be used for EMC pre-testing in the frequency range of 150kHz to 110 MHz.
-
Product
Audio Line Drivers and Receivers
-
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
Product
Phase Sequence Indicators (Contact Type)
887 PR
-
Standard Electric Works Co., Ltd
● Indicates phase rotation. ● Indicates phase presence.● No battery required.● Phase rotation phase presence indicated on large liquid crystal display.● Small, rugged enclosure.● Color coded test leads.● Phase presence indication from as low as 40Vac to as high as 600Vac.● Fused.● Lightweight, robust and compact.● EN 61010-1 CAT III 600V EN 61010-2-032
-
Product
Programmable Delay Line Instrument
XT-100-OEM
-
With the XT-100-OEM, all the capabilities and precision of the XT-100’s trombone technology can be built right into your own system. This product is intended primarily for OEM applications so you have a streamlined solution for precision phase shift or programmable delay.
-
Product
Pen-based Fault Locator
-
*Find the breakpoint, bending or cracking*Find the fault of OTDR dead zone*Identification of fiber from one end to other end*Universal adaptor*Testing distance up to 8km*Lightweight, red laser output, both SM and MM available
-
Product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
-
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
-
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
Product
Digital Fault Recording
SHERLOG
-
Fault recorder systems with a power quality analyser for comprehensively monitoring and assessing low, medium and high voltage networks in power plants and transformer substations. The measuring devices of the SHERLOG range make very high-resolution recordings of all the disturbances which occur in power supply systems. The behaviour of protection and switchgear devices during these system disturbances is recorded at the same time.
-
Product
Cable Fault Finder
-
Techno Instrumentation (India) Private Limited
Magnetic and Acoustic signal strength through bar graph and digits on LCD.Coincidence feature gives distance to the fault in milliseconds.Easy, fast and accurate pinpointing of faults.
-
Product
For Overhead Distribution Line Current Tester With Power Flow Direction Record
MHR-600
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Measuring and recording the average current values & power flow directions in the setting interval.・Easy to use, as an indirect hot-line work tool.・Memorized data can be outputted to USB memoryafter measurement.・For 6.6KV circuit, protection level IP64.
-
Product
Single Sensor - Monochrome Line Scan Cameras with Fast Scan Rates
-
JAI’s monochrome line scan cameras provide an excellent combination of high resolution and fast scan rates.The Sweep SW-8000M-PMCL model features an 8192-pixel linear CMOS sensor delivering a line rate of 100,000 lines/s (100 kHz) over a Camera Link interface. The SW-4000M-PMCL model is based on a 4096-pixels sensor capable of running as fast as 200,000 lines/s (200 kHz) over Camera Link.
-
Product
Programmable Selsyn Indicators
PSI
-
Computer Conversions Corporation
Computer Conversions Solid State Selsyn/Resolver Indicator digitizes the outputs of Selsyns, Synchros and Resolvers for position indication and control applications. The Selsyn Indicator is designed to replace failure prone mechanical selsyn torque receivers, counters, etc. The tracking converters high noise immunity and high speed tracking characteristics make it ideal for use in industrial envrionments.
-
Product
Optical Coherence Tomography Imaging Line Scan Cameras
OctoPlus Range
-
Teledyne e2v spent 2 years developing a CMOS sensor specifically for OCT. This resulted in the launch of OctoPlus, which has a specially designed pixel architecture that improves sensitivity and reduces signal roll-off to improve image quality by several dB vs state-of-the-art CMOS cameras, especially in deep structures.
-
Product
Magnetic Level Indicator
VEGAMAG
-
A safe, durable, and non-invasive instrument used to measure liquid levels in tanks or pressurized vessels.
-
Product
Broadband Digital Signal Delay Lines
-
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-32Gbps / DC-17GHz) tunable clock/data phase shifterDelay adjustment range of 265psExhibits low jitter and limited temperature variation over industrial temperature range1GHz of bandwidth for the phase adjustment tuning portFully differential CML input interfaceFully differential CML output interface with 600mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 1WFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
Product
Visual Fault Locator ( VFL)
TM315N
-
The TM315N Economical VFL is an efficient and low cost basic fiber test tool, it provides a visible way to find fiber faults and identify fibers in an optical network during and after installation.
-
Product
PXI 11-Channel 2A Fault Insert Switch
40-202-101
-
This is the 11 Channel version of the 40-202 Fault Insertion Switch. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test
-
Product
Standard Tap Position Indicator
-
NMC,s Tap Position Indicator is a Microprocessor based specially designed instrument used to indicate the Tap Position of the Power Transformer with On Load Tap Changer.
-
Product
Flow Indicator
Qualitrol 092
-
Designed to indicate “pump on” and “pump off” conditions within a forced cooling system. Select models also indicate flow direction. Up to two SPST or SPDT switches are available for control and/or alarm functions. Large dial face provides easy viewing and is magnetically coupled to the flange assembly allowing leak free replacement if damaged.
-
Product
USB Line Camera
-
The USB Line Camera is an easy-to-use cost-effective board-level line scan camera. It consists of two circuit boards, the main circuit board and the sensor circuit board.
-
Product
Telephone Line / Load Analyzer
TLLA-2500 Pro
-
Detects and Alerts the user of almost ANY Telephone Wiretap (Tap), even from the Telephone Central Exchange (REMOBS), with the added ability of defeating common types of wiretaps.
-
Product
Cable Fault Locating Equipment
-
Commonly used to test underground coaxial and twisted pair cabling, along with transmission lines and other industrial electrical cables.
-
Product
Fault Locator
BIDOYNG
-
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
Product
Fault Injection Module
WF 3154 C-Series
-
The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel provide three solid state relays that can be used to create electrical fault conditions like: Open circuit, Short circuit to battery, Short circuit to ground.
-
Product
EPON OLT ( Optical Line Termination )
OLT-1408
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OLT-1408's Optical Line Terminal (OLT) adopts GiGA Ethernet Passive Optical Network (EPON) technology. It is a compact chassis with L2/L3 GiGA switching and routing function. All the functional components are modularized design and it supports hot-plugging with plugging and playing. 1~4 pieces of GiGA optical port or electrical port are optional in the uplink port, which provides a direct optical interface for the Ethernet/IP network core. 1~8 pieces of EPON optical port are optional in the down link port. Through a passive optical Network (PON), an optical Network unit link (ONU),it can provide final transmission with bandwidth up to 1Gbps for the user.
