Line Fault Indicators
See Also: Overhead Line
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A
40-191B-012
Fault Insertion Unit
The 40-191B is a PXI fault insertion switch using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
Economic Type Strain Gauge/Load Cell Indicator
CS1-SG
-
CS1-SG economic type strain gauge/load cell indicator is equipped with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV.It supports field calibration, and It can calibrate with sensor (load cell/strain gauge) according to actual needs.It is able to select one from these three functions, 1 relay output, 1 analogue output or 1 RS-485 (Modbus RTU Mode) interface; they provides many functions such as control, alarm, re-transmission, and communication.
-
Product
Pen-based Fault Locator
-
*Find the breakpoint, bending or cracking*Find the fault of OTDR dead zone*Identification of fiber from one end to other end*Universal adaptor*Testing distance up to 8km*Lightweight, red laser output, both SM and MM available
-
Product
Voyager Intermittent Fault Detection Tester
-
This family of testers is available as the portable VIFD™ tester (previously called the Ncompass-Voyager) with 128, 256 or 512 test points, and it is available as a 19” rack-mount system – the IFD & Isolation System (IFDIS™) – with thousands of test points. Testers are available from Copernicus Technology for purchase or lease. Alternatively we can provide the full test service for you and we also provide all the corresponding test accessories listed under the Test Equipment menu button.
-
Product
Automated Control System for Veneer Edge Gluing Line
Vikat
-
The automated veneer splicing line control system is designed to identify defective veneer areas, control the scrap trimming, bonding of suitable areas and the formation of output sheets of a given size.
-
Product
Phase Sequence Indicators (Contact Type)
887 PR
-
Standard Electric Works Co., Ltd
● Indicates phase rotation. ● Indicates phase presence.● No battery required.● Phase rotation phase presence indicated on large liquid crystal display.● Small, rugged enclosure.● Color coded test leads.● Phase presence indication from as low as 40Vac to as high as 600Vac.● Fused.● Lightweight, robust and compact.● EN 61010-1 CAT III 600V EN 61010-2-032
-
Product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2320
-
CableTroll 2320 is an indicator for detection of Earth faults (PtG) and short circuit (PtP) faults on multi-core and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
Frequency, Rate Meter, Flow Rate Indicator
-
Two independent scalable pulse-input channels from 0 Hz to 1 MHz. Channels may be combined arithmetically. One channel can display total while other displays rate. High read rate for control applications: AC line frequency can be measured to 50.0000 or 60.0000 Hz in a few line cycles. Ideal for use as a tachometer or readout of a turbine flow meter.
-
Product
Wafer Auto Line Integration
-
The line is used for semiconductor wafer grinding. It carries out material matching and distribution, automatic loading and unloading, auto focusing and positioning and many other functions. The grinding precision is 2μm(3-sigma). It is also capable of collecting and analyzing real-time production data and interfacing with MES system.
-
Product
Test Line • Perforation counter
Perforation counter PZ 3
-
The perforation counter PZ 3 can be used among other things in the production of plastic bags and garbage bags. By the non-contact perforation detection, for example, the number of bags / batches can be determined and the roll change can be initiated.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
Fault Insertion Unit
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
40-204-001
Multiplexer Module
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
Pole Mounted Detector of PtG and PtP faults in 6-69V Line
LineTroll 111K
-
The unit mounts 3-5m below the conductors and monitors all three phases. The indicator is powered by replaceable long-life lithium batteries which have a lifeexpectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
Fiber Visual Fault Locator
-
Fiber visual fault locator is a pen type device which is able to locate the breakpoint, bending or cracking of the fiber glass,this small fiber optic equipment can locate the fault of OTDR dead zone and make fiber iIdentification from one end to the other end .
-
Product
X-Ray Line Camera
X-Scan C
-
Slim, plug-and-play-type, water-resistant X-ray line cameras for harsh industrial environments.
-
Product
Coking Coal Indices Determinator
-
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
Is used to determine the plastometric indices of bituminous coal (maximum thickness of plastic layer Y, final contraction value of plastic layer X) and describe technical characteristics of coke, which helps to guide coking and coal blending . It is widely applied in coal mining, metallurgy, chemical industry and verification institution of coal quality.
-
Product
Telephone Line Testers for POTS / Analog Line
-
*This analog line tester is suitable for all instalers installing telephone equepement on POTS line.*Led indications signaling the status of analog line.
-
Product
625 KHz Data Acquisition Multifunction (Analog Output X2 Lines) PCMCIA
DAQi616MF(MF236/i)
-
The DAQi616MF is a type II PCMCIA I/O card for notebooks and other computers containing a PCMCIA slot.
-
Product
Digital Tap Position Indicator With Voltage Display
-
NMC's Digital Tap Position indicator with Voltage Display, type: TX-202, is used to indicate the Tap Position of the Power Transformer with On Load Tap Changer as well as also indicates the voltage.
-
Product
Visual Fault Locator
TM191
-
TM191 series visual fault locator is used for the measurement in single mode or multi-mode fibers. It features a rugged design, a universal connectorand an accurate measurement
-
Product
Step-Tunable Laser Source, High Power and Low SSE, Basic Line
N7779C
Laser Source
The new N7779C basic line step-tunable laser source is ideal for cost-effective testing of broadband optical devices. It can also serve as a highly stable, tunable local oscillator for receiver testing or transmission experiments.
-
Product
RF In Line Digital Power Meter
DPM-50
-
DPM-50 features high dynamic range, high accuracy and high stability, it works with PC monitoring software and optional handheld monitor to perform real-time in-line monitoring on entire antenna system and saves test data for analysis and evaluation.
-
Product
Remote Indicators
-
ABB field indicators provide a convenient way to access the field instruments data when they are located in remote or difficult to access areas. Powered directly from the 4-20 mA current loop, they require minimal effort to setup.
-
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicator will need to be mounted in to a case or control rack for safe use.
-
Product
Line Noise and Vibration Test Systems
-
The sound and vibration characteristics of your product can be used to identify many common mechanical and assembly defectives.
-
Product
Very Compact Linear Line Array Loudspeaker
LINA
-
Easily the smallest and lightest in the series, LINA and its companion control element 750‑LFC bring the inherent linearity, low distortion, and exceptional power-to-size ratio of LEO Family technology to a wider range of applications and venues.
-
Product
Continuity Tester with Audible & Visual Indication
TEK404
-
The Martindale TEK404 is a low cost, easy to use continuity tester. It has audible and visual indication plus overvoltage protection. It has the same loud buzzer as the TEK402, giving a very clear signal of continuity.
-
Product
Fault Injection Module
WF 3154 C-Series
-
The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel provide three solid state relays that can be used to create electrical fault conditions like: Open circuit, Short circuit to battery, Short circuit to ground.
-
Product
Visual Fault Locators
-
Visual fault locators are used to identify problems with your fiber. GAOTek visual fault locators typically are applied for fiber tracing, fiber routine, and continuity checking. Imagine being able to easily identify when and where a fiber is breaking, bending, or when there’s a threat to the fiber layer.
