Line Fault Indicators
See Also: Overhead Line
-
Product
Loop A Line Products
-
Cable pair tracing and a lot more, Loop-a-Line products can remotely control a far end device (the oscillator) for up to 20km of cable. Using a Loop-a-Line allows the linesman to remotely change the state of the oscillator to any of five different states. Therefore eliminating the need for multiple journeys along the cable path.
-
Product
RS-232 Line Driver with Control Signals and LCD Display
Model 224
-
FEATURES: DataSpy® Status Display; Full Duplex & Handshake; Loopback & DTE/DCE Switch; DC to 19.2 KBPS; Supports DTR & DCD; Optically Isolated. The Model 224 RS-232 Line Driver with Control Signals and LCD Display provides for transmission of a handshake signal in each direction, in addition to communicating full duplex data up to 19.2 KBPS and providing complete optical isolation.
-
Product
Classic Collet | Back | Without Line | Matt Or Glossy | Ø 10 Mm
020-2x20/5
-
Secure plastic mounting cap for collet or wing knob
-
Product
Phase Sequence Indicators (Contact Type)
888 PMR
-
Standard Electric Works Co., Ltd
● Indicates phase rotation. ● Indicates phase presence.● Indicates motor rotation/wiring.● Indicates battery status.● Phase rotation and motor rotation indication works from as low as 1Vac.● Small, rugged enclosure.● Color coded test leads.● Phase presence indication from as low as 100 Vac. ● Very low consumption.● Fused. ● Lightweight, robust and compact.● Works from 2 Hz to 400 Hz Sine.
-
Product
SparkFun Line Sensor Breakout
QRE1113 (Digital)
-
This version of the QRE1113 breakout board features a digital output, using a capacitor discharge circuit to measure the amount of reflection. This tiny board is perfect for line sensing when only digital I/O is available, and can be used in both 3.3V and 5V systems.
-
Product
Broadband Digital Signal Delay Lines
-
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-32Gbps / DC-17GHz) tunable clock/data phase shifterDelay adjustment range of 265psExhibits low jitter and limited temperature variation over industrial temperature range1GHz of bandwidth for the phase adjustment tuning portFully differential CML input interfaceFully differential CML output interface with 600mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 1WFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
Product
Waspmote Plug & Sense! Encapsulated line
-
Libelium Comunicaciones Distribuidas S.L
Robust waterproof IP65 enclosure.11 models integrating more than 150 sensors.Add or change a sensor probe in seconds.Solar powered with external panel.Radios: 802.15.4, 868, 900, WiFi, 4G, Sigfox and LoRaWAN.Over the Air Programming (OTA).Special brackets ready for street lights installation.Fully certified for the main markets: CE, FCC, IC, ANATEL, RCM, PTCRB, AT&T.
-
Product
Non Contact Voltage Indicator
PL107N
-
Contact-free audible and visual indication of AC voltages between 90 and 1000 V AC Clear, omnidirectional flashing LED Quick and accurate detection of cable breaks Detects microwave leakage Phase detection in sockets Press to test switch avoids nuisance buzzing and extends battery life Supplied complete with 1.5 V AAA batteries
-
Product
Cable Continuity Tester, RS232, DB9 In Line Signal, Network, 21.01 mm, 35 mm, 45.01 mm
72-9265
-
The 72-9265 is an In-Line Signal Link Tester. Quickly test DB9 connections with this handy tester. No need to carry bulky, expensive cable testers to test only one or two cable types. Mini link tester fits easily in your pocket or tool box and requires no external power. Connects in-line and displays signal data connectivity on LED's per each conductor. Save time and money by diagnosing connectivity issues.
-
Product
High Line Pressure Variable Reluctance Pressure Sensor to 10,000 psid
DP360/DP363
-
The DP360 can be calibrated for a full scale as low as ±50 psid while withstanding high static line pressure. Low differential pressure may be measured at static pressures as high as 10,000 psig with a maximum 3% FS zero shift error.
-
Product
Ground Fault Analyzers and Detectors
-
The Model 760 detects and locates accidental ground faults on both energized and de-energized power circuits including single phase, three phase, and DC ungrounded systems.
-
Product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2310
-
CableTroll 2310 is an indicator for detection of earth faults (PtG) on multi-core and single core cable terminations. The unit uses NorTroll type current sensor (CT)
-
Product
Cable Sheath Testing and Fault Location System
Shirla
-
Cable fault location with the BAUR shirla. Shirla the fault location system is used for cable and cable sheath testing as well as for pre-location and pinpointing of cable faults. The pre-location based on the measuring bridge principle according to Murray and Glaser that is designed especially for power cables, also enables pre-location for control and lighting cables. Null balance and evaluation take place automatically.* Cable and cable sheath testing up to 10 kVC* Resistance measurement* Cable and cable sheath fault pre-location with precision measuring bridge* Adjustable cable sections that can be defined with length, conductor cross-section and material respectively and can be considered in the distance calculation
-
Product
Vehicle Mount Cable Fault Location System
-
Weshine Electric Manufacturing Co., Ltd
VS2088Plus Built in Booster And Capacitor In Vehicle Underground Cable Fault Test Device
-
Product
3 GHz, 4 Channel Programmable Delay Line
QPADL3
-
The QPADL3 is a programmable delay line instrument with 4 independent channels designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 3 GHz.
-
Product
Phase Indicators
-
Kyoritsu Electrical Instruments Works, Ltd.
New technology permits safe testing, without the need of direct contact between probes and live wires. The insulated crocodile clips can clip insulated cables from 2.4 to 30mm. Phase rotation is indicated by the rotary illumination of LEDs and logical audible tones. The instrument can be fixed to a metal panel via the magnet on the back side. Wide measuring range for 3 phase installations from 70V to 1000V AC. Super brightness function permits clear LED''''s indication also in sunshine. Complies with IEC 61010-1 CAT IV 600V and CAT III 1000V.
-
Product
RS-232 Micro Line Driver - DB9 Connector
Model 209
-
FEATURES: Compatible with PC; 386/486 Pentium Com Ports; Full Duplex to 19.2 KBPS; No AC or DC Power; Screw Terminals or RJ-11; Small Size. The Model 209F offers all the features of the Model 201 Short Haul Modem but in a package that is approximately one third the volume.
-
Product
Fault Simulation
Concurrent Fault Simulator
-
TurboFault combines high performance, versatility and accuracy. It is highly competitive with hardware accelerators for classical test fault grading. It supports synchronous and asynchronous designs at the gate level, including tri-state gates, latches, flip-flops, single and multi-port RAMs, complex bus resolution functions, and User Defined Primitives (UDPs).
-
Product
Power Transmission Line Inspection System
-
Shandong Senter Electronic Co., Ltd
With the aid of high-end technology and equipment, Senter Electronic manufactures and trades high-tech power transmission line inspection system with low price. And we are known as one of the leading such manufacturers and suppliers in China for our quality products and good service. Welcome to buy the power transmission line inspection system with our factory.
-
Product
Mobile Cable Fault Location System
BAUR Syscompact 4000
-
Fault location with Syscompact 4000. The Syscompact 4000 is a compact, fully enclosed fault location system for pre-location and pinpointing of high-resistive, low-resistive and intermittent faults on low- and medium-voltage cables. Easy operation and the use of latest fault location methods enable fast and safe fault location.* Location of low-resistive, high-resistive and intermittent cable faults* Efficient cable fault pre-location methods* Pinpointing according to the noise location method or acoustic propagation time measurement* (with Universal Locator and ground microphone)* Sheath fault location according to the step voltage method (with Universal Locator and two measurement probes)* Easy to handle
-
Product
Load Cell Indicator
9840
-
The 9840 is suitable for use in calibration labs, field service, or anywhere high accuracy is important. Features include a bipolar 6-digit 2-line display, remote sense, low noise, 22-bit resolution, USB port with RS232 communication, mV/V calibration and the ability to store up to 25 different sensors. 6-point linearization, unit conversion, front-panel tare. Self calibration via TEDS Plug & Play ready IEEE1451.4 compliance.
-
Product
KYZ Indicator and Tester
1031-C3, 1031-C6
-
More than just an indicator, TESCO’s KYZ Indicator and Tester Cat. 1031-C3 (3-wire) and 1031-C6 (6-wire) can also be used to perform accuracy testing of KYZ pulses on all TESCO Next Generation Test Equipment. TESCO’s KYZ Indicator and Testers can be used as a pulse input using the same pickup connection on the front panel of all TESCO Next Generation Test Equipment.
-
Product
PXI Single Bus 64-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-401
Fault Insertion Unit
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
6 GHz, 4 Channel Programmable Delay Line
QPADL6
-
The QPADL6 is a programmable delay line instrument with 4 independent channels designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 6 GHz.
-
Product
Classic Collet | Black | With Line | Matt Or Glossy | Ø 36 Mm
021-6x20/5
-
Secure plastic mounting cap for collet or wing knob
-
Product
Wireless Weighing Indicator Series
-
Ningbo Yaheng Electronic Technology Co.,Ltd
YEAHEVER Wireless Weighing Indicator Series
-
Product
High-Speed Optical Delay Line
-
The Peregrine Optical Delay Line (1-cm, 60 ps delay) and the Gyrfalcon Optical Delay Line (2-cm, 120 ps) are high-speed, high precision, voice coil motor optical delay lines. They have zero-backlash and no hysteresis. Both have similar form factors that are compatible with 30-mm cage components and 1.035” – 40 threads. Both include full digital and analog control and include a USB interface.
-
Product
Visual Fault Locators
-
Visual fault locators are used to identify problems with your fiber. GAOTek visual fault locators typically are applied for fiber tracing, fiber routine, and continuity checking. Imagine being able to easily identify when and where a fiber is breaking, bending, or when there’s a threat to the fiber layer.
-
Product
Intelligent Cable Fault Locator
TM800
-
TM800 Cable Fault Locator is a portable field instrument working on TDR and bridge methods, adopting advanced micro-electronics technology. It is designed to locate accurate fault points in such cables as telecommunication leadsheathed cable, plastic cable or user’s lead covered wire, while the faults include break, mix, earthing, defective insulation, or poor connecting. It is and ideal function-stable instrument for the field operator to improve work efficiency, in addition, it can also be used for circuitry project checking electric property testing of the cable.
-
Product
Classic Collet | Black | Without Line | Matt Or Glossy | Ø 28 Mm
020-5x20/5
-
Secure plastic mounting cap for collet or wing knob
