LED Sources
emit light as a reference or to illuminate.
See Also: Light Sources, Optical Light Sources
-
Product
Broadband Coaxial Noise Sources
-
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
Product
Light Source
UVF-352S
-
This is the ultra high power unit fully utilizing the high stability and long life 350watt ultra high pressure mercury lamp. The unit is made to compact size.
-
Product
Mobile Communications DC Source, 15V, 3A
66311B
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66311B mobile communications DC source provides fast transient, exceptional sourcing, and precision measurement.
-
Product
Source Phase Control
S96088B
-
The S96088B allows users to set calibrated, arbitrary phase differences between two signal sources running on the E5080B ENA.
-
Product
High Temperature Source
-
The Veeco High Temperature Source provides thermal evaporation of charge materials at temperatures up to 2000°C. This compact MBE source operates efficiently to achieve high temperatures without excessive thermal load on the system. Low power requirements also enhance the lifetime of the heater filaments.
-
Product
5cc Dual Dopant Source
-
Attain precise and stable control of relatively low fluxes for dopant constituents in molecular beam epitaxy (MBE) through this compact dopant source. Its small thermal mass gives it excellent responsiveness, reproducibility, and stabilization for advanced doping profiles, plus consistent flux uniformity across an entire platen. Efficient cell heating minimizes thermal load.
-
Product
Network Analyzer, Lan Tester, LED
72-6290A
-
The 72-6290A is a multi-modular Cable Tester (LAN Tester) with LED meter display. Requires 9V battery for this modular cable tester. Used with RJ-45, RJ-12, RJ-11 connectors and USOC4, USOC6, USOC8 cables.
-
-
Product
Source Systems AC
-
The power sources of MTS-series based on digital amplifier modules combined with frequency generator and reference device are the MTS source system. Single-phase systems (MTS1xx) or three-phase systems (MTS3xx) from 1 to more than 40 test positions are available.
-
Product
Isolated Voltage Source
SIM928
-
Stanford Research Systems, Inc.
The SIM928 Isolated Voltage Source is ideal for applications where ultra-clean DC voltage is required. Voltage can be set between ±20 VDC with millivolt resolution, and the source can drive up to ±10 mA
-
Product
Long Life Serismic Energy Source
2800LLX
-
Bolt introduced the LONG-LIFE air gun in 1992. Since then it has become the standard energy source for marine seismic exploration.
-
Product
Handheld Optical Light Source
JW3109
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
An easy-to-use optical light source which offers high accuracy and is used to test single and multi-mode optical fibers by using 1 to 4 output wavelengths.
-
Product
R*evolution® Remote Plasma Source
-
The innovative R*evolution® Remote Plasma Source combines field-proven, low-field toroidal plasma technology with an actively cooled plasma chamber made of high purity quartz, significantly reducing oxygen, hydrogen and nitrogen atomic gas loss through wall recombination. Self-contained and compact, R*evolution delivers up to 10 slm of oxygen radicals from a 6kW power supply with true power accuracy of <1% resulting in a high density, extremely clean radical source for photoresist strip and an optimal clean rate greater than 12 microns/min-1. R*evolution can be used for other surface preparation applications.
-
Product
HYBRID LED CIRCUIT TESTER, 12-42V
MD1651
-
*Tests standard automotive electrical DC 12-42V circuits*Safe for low current circuits and hybrid vehicles*Automatic voltage identification featuring blue for under 40V and red for over 40V
-
Product
Noise Sources
WGNS
-
The system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device operating in the 26.5 – 170GHz range on wafer as well as in benchtop applications. Farran offers the WGNS series of noise sources to be used in conjunction with the FBC down converters for use as frequency extenders for noise figure measurement test system.
-
Product
Light Sources
-
Fiber optic light sources are a low-cost way to analyze and identify accurate fiber optic readings, while certifying optical fiber. Receive the ability to measure fiber optic light continuity, loss, and quality of the signal.
-
Product
Handheld Digital Multimeter, 4.5-digit, with Organic LED Display (OLED)
U1253B
Digital Multimeter
The Keysight U1253B 4.5-digit handheld digital multimeter (DMM) is feature-packed to simplify the troubleshooting of electronics and electrical circuits indoors, on the bench or in the field. Key capabilities include its organic LED (OLED) display that provides razor-sharp readings even in dark, off-angle situations. The U1253B is the world's first OLED handheld DMM of its kind. For those long, continuous measurements, the DMM equips you with the easy-to-use GUI data-logging software to automate virtually unlimited data recordings to PC. The U1253B comes with an integrated 20 MHz frequency counter for high frequency measurements, and a built-in programmable square-wave generator with selectable frequency and duty cycle. With the versatile U1253B, you are well equipped to perform thorough troubleshooting of any faulty circuit.A multi-award winner
-
Product
10 MHz to 55 GHz Noise Sources
CNS346 Series
-
The Spanawave CNS346 Series is designed for precision noise figure measurement applications. The superior VSWR characteristics reduce multiple reflections of the test signals and significantly increase the measurement accuracy of most noise figure set-ups. The CNS346 Series noise sources have broadband coverage and extremely good temperature and voltage stability, for the finest noise figure meter-compatible laboratory standards. Outputs of 6, 15.5 and 22 dB ENR are available, allowing the units to accurately measure noise figures up to 20 ,30 and 36 dB respectively.
-
Product
LED Lighting Drivers
-
Renesas' dimmable AC mains LED driver with PFC and primary side regulation provides all of the features required for high-performance dimmable LED ballast designs and supports AC or DC input, isolated or non-isolated flyback and boost topologies.
-
Product
PXIe-4143, 4-Channel, ±24 V, 150 mA Precision PXI Source Measure Unit
782431-01
Source Measure Unit
PXIe, 4-Channel, ±24 V, 150 mA Precision PXI Source Measure Unit - The PXIe-4143 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4143 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4143 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
50-Pin DIN-Rail Wiring Board W/ LED Indicators
ADAM-3951
-
Low-cost DIN-rail mounting wiring terminal module for PCI-1752/1754/1756 with 50-pin SCSI female connectorScrew-clamp terminal blocks allow easy and reliable connectionsEach LED indicates its current bi-directional I/O logic status with either green or red lightCase dimensions (W x L x H): 77.5 x 179.5 x 41.5 mm (3.1" x 7.1" x 1.6")To Be Used With PCI-1752U, PCI-1754, PCI-1756
-
Product
Uniform Light Sources, Luminance Standards
-
Uniform light sources for the adjustment of pixels and intensity of image sensors and cameras as well as for the calibration of luminance and spectral radiance or in other words: Solutions for Imaging, Sensing & Remote Sensor Calibration.
-
Product
Noise Source
MNS-1
-
Matrix Test Equipment Incorporated
The MNS-1 is a shaped noise source that can be used toemulate 2 bands of digital carriers. While it does not havethe necessary attributes to generate a constellation, it doesmimic the loading of QAM carriers. The MNS-2 featuresremotely controllable 6 MHz wide notch filters to allowintroducing a QAM carrier capable of generating a constellationand enabling measurement of Modulation Error Ratio (MER) andBit Error Rate (BER).
-
Product
16-Ch Isolated Digital I/O Module With LED
ADAM-5055S
Digital I/O Module
I/O Type: 8 DO & 8 DIOptical Isolation: 2500 VdcPower Consumption: 0.68 W (Typical)16-channel
-
Product
Clean Power Source
AC1000A
-
The AC1000 achieves its unique price/performance ratio by actively adjusting the incoming mains waveform to produce a clean output. Other suppliers use convertor techniques to completely recreate the output from scratch. Our solution delivers an output which achieves the required THD with the minimum of hardware and expense. It includes the ability to switch the correction in or out so that the original waveform can be observed and measured if required. Overload and thermal protection systems are built-in and produce an audible warning if activated.
-
Product
Tunable Deuterium and Tungsten-Halogen Light Sources
-
Deuterium and Tungsten-Halogen tunable light sources are convenient and affordable solutions for your laboratory experiments. Their optimized optical design, delivers efficient and power stabilized broadband optical power with variable aperture and selectable bandwidth with wavelength ranging from 180 nm up to 2 micron depending on your choice of the lamp.
-
Product
Source Phase Control
S95088B
-
The S95088B allows users to set calibrated, arbitrary phase differences between two signal sources on the M980xA PXI VNAs.
-
Product
27" Flat Touch Display With Surround LED Strip
IDP31-270W
-
27" flat touch display with surround LED strip, full HD resolution and multiple input sources VGA/DVI/DP. 27" Full HD 1920 x 1080 resolution, 0 ~ 45 °C range operating temperature, P-cap touchscreen and glass solutions.
-
Product
ELSFP External Laser Source
ELSFP 1000 Series
-
The ELSFP 1000 Series is a high‑power, multi‑channel external laser source designed to deliver stable continuous‑wave optical output for scalable CPO and PIC testing.It provides up to eight channels of stable CW power of up to 25 dBm per channel using the External Laser Small Form‑Factor Pluggable (ELSFP) standard to support realistic power distribution and simplify high‑channel‑count CPO and PIC test setups.
-
Product
SpikeSafe DC / Continuous Pulsed Current Sources
-
The Vektrex SpikeSafe™ DC / Continuous Pulse (DCP) Current Sources provide reliable DC or pulsed drive for LED or laser diode reliability testing, IESNA LM-80 maintenance testing, and other test applications requiring DC or continuous pulse current. Models support currents from 500mA to 60A and compliance voltages from 50V to 400V. All models feature individual channel control, accurate pulsing over long output cables, precise current, precision pulsing for improved measurement repeatability, and high power density — typically 6.4kW-8kW.
