LED Sources
emit light as a reference or to illuminate.
See Also: Light Sources, Optical Light Sources
-
Product
LED Backlight Drivers For Automotive
-
Renesas' automotive LED backlight drivers offer dimming solutions for a wide variety of ambient lighting conditions in automotive applications.
-
Product
Basic AC Sources
AC6800 Series
-
Achieve more stable and reliable basic AC power measurements up to 4000 VA Easy operation with an intuitive user interface Access and control the power source remotely via LAN/LXI Core, USB or optional GPIB Lower your cost of ownership with global support & longest standard warranty in the industry
-
Product
Four Quadrant Power Source
PM2010
-
The PM2010 is a four-quadrant power source capable of supplying up to 20 V/10 Amps to a load. The maximum power that may be safely generated is 50 Watts on a continuous basis and 200 Watts peak on a pulsed mode for no more than 100 ms, and a duty cycle of less than 10%
-
Product
SparkFun LED Driver Breakout
LP55231
-
The SparkFun LP55231 LED Driver Breakout is a self-contained solution for developing and deploying the nine-channel I2C LED controller. Remarkably simple, the breakout is equipped primarily with just the LP55231 LED controller IC, plus three RGB LEDs. It also features pads and jumpers for replacing the onboard LEDs with external ones, and configuring the I2C bus, which allows you to daisy-chain up to four LP55231s. This breakout drives the LEDs using Pulse Width Modulation (PWM), so it is well-suited for variable intensity and color-mixing applications!
-
Product
Garmin LIDAR-Lite V4 LED
Distance Measurement Sensor (Qwiic)
-
The LIDAR-Lite v4 Qwiic from GARMIN is a high-performance, wireless optical distance measurement sensor that doesn't require any soldering to get started. This is the ideal solution for drone, robot, IoT, or unmanned vehicle operations when space is tight and power is limited. This sensor has up to a 10 meter range, 1cm resolution, and requires 85mA during data acquisition. The user can read and write to the LIDAR-Lite v4 using the I2C protocol; this is where the addition of the SparkFun Qwiic system really shines. The LIDAR sensor requires 5V to operate but runs on 3V3 logic. With a 5V boost circuit and an easy-to-use Qwiic connector you can power the sensor and get distance measurements over Qwiic all with a single piece of hardware.
-
Product
LED Color Sensor
FINN®
-
The FINN® is a compact and durable LED sensor that is able to fit in just about any test setup. There are two different configurations to accommodate your set up needs - right angle and vertical styles. The FINN® is color specific, so pick your style and match to the color of the LED you want to test.
-
Product
10 GHz Signal Source
YIG Series
-
The SC5503B and SC5502A are designed to meet demanding low phase noise applications. This is accomplished by employing a multiple phase-locked loop architecture as well as a YIG oscillator as the heart of its synthesizer. Frequency accuracy is provided by an onboard 10 MHz temperature compensated crystal oscillator (TCXO) which can be phase locked to an external reference source if required. These modules can be used as standalone CW signal sources or as LO sources for frequency conversion systems such as the SignalCore IQ modulators and demodulators. They are designed to meet the requirements of many modern applications such as wireless device testing, software-defined radio research, point-to-point radio, multi-channel coherent systems, and other academic and military programs.
-
Product
SMD LED Aging Test Machine
CX-6100
-
Shenzhen Chuangxin Instruments Co., Ltd.
Designed to measure the aging-life and color comparisons of 50pcs 5050 SMD LED and 100pcs 3528 SMD LED.• 150 separate constant current supply• Aging functions: constant current, impact pulse, on-off mode• Range of forward voltage(VF): 5.0V• Range of forward current(IF):1) constant current: 0-100.0mA2) Impact pulse: 0-200.0mA• Range of impact pulse frequency: 10-9999Hz; Duty ratio: 1%-99%
-
Product
Desktop Tunable Laser Source
UC8110
-
The UC8110 desktop tunable lasers offer superior performance for the test of DWDM components, AWG & PLC components, optical amplifiers, DWDM system and other general purpose of fiber optical test and measurement applications. It is a wavelength high accuracy, high power output, small dimension, fast startup, affordable tunable laser source system. UC INSTRUMENTS provides C band, L band, or C+L band tunable laser sources options.
-
Product
Multi-Channel, Programmable Current Source
CS-48-100
-
The Model CS-48-100 is a multi-channel, programmable current source. Developed for both semiconductor and digital superconductor electronics, it is computer-controlled and features 48 low noise current source outputs. Each source output has the capability to both set and read back currents and can be set to a zero current high Z mute state. Each of the 48 sources are optically coupled for control and are sourced from their own secondary winding for complete galvanic isolation. The device consumes a maximum of only 80 W and handles a maximum load current of 4.8 A total over all outputs. Operating over a range of 0-100 mA on each channel, the device features accuracy of +/-25 ?A. The mute state can be set thru a rear panel interlock or from the front panel button for maximum circuit protection. The unit can be mounted in a standard-sized rack.
-
Product
Mini Visual Laser Source
TM536 Series
-
TM536 Series Mini Visual Laser Source totally complies with the human engineering. It's small in size, easy to operate, portable and integrated with a launching indicator. A Visual Laser Source is usually used to inspect the damaged or broken point of a optical fiber, cable, patchcord and etc.If the inspected fiber does have a defect, user could find the visual laser at the broken or damaged point. TM536 Series Mini Visual Laser Source is suitable for both single mode and multimode fibers. The performance of the visual laser source will act a little different on different fiber coat and color.
-
Product
AC Power Sources
RS Series
-
AMETEK Programmable Power, Inc.
The RS Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the RS series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the RS unit to its designated location (using included casters), plug it in, and the RS series is ready to work for you.
-
Product
High-Power Noise Sources
-
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
Product
White Light LED Illumination System
pE-300lite
-
CoolLED's pE-300liteis a simple white light LED illumination system that offers intense, broad-spectrum LED illumination for imaging most common fluorescent stains. The pE-300lite Light Source can be fitted directly to the microscope or specified with a liquid light guide. The system is a mercury-free alternative that is safer, more controllable, and repeatable than conventional high-pressure gas discharge illuminators. Spectral coverage is from the UV (DAPI excitation) to the Red region (Cy5 excitation). The system is perfect for hospital and regular research laboratory environments and is affordable within consumables budgets.
-
Product
ESD SURFACE RESISTIVITY METER (WITH 10 LEDS)
-
Simply place the meter on the surface of the material that requires measuring.Press the green test button. The meter will then light the appropriate LED from 10 to the power of 3 to 10 to the power of 12 Ohms per square or insulative.
-
Product
LED Inspection
-
Indicates which LEDs are not working. Checks if all diodes are placed in the correct places. Independently configures a test program for each new LED panel. Fast and effective – 1000 LED panel test takes up to 3 seconds.
-
Product
Network Analyzer, Lan Tester, LED
72-6706
-
The Tenma Multi-Network and Modular Cable Tester easily reads the correct pin configuration of 10Base-T cable (Category 5, 5e and 6), 10Base-2 cable (coax), RJ-45 and RJ-11 modular cables, 356A, TIA-568A/568B and Token Ring cable by comparing transmitting end to the corresponding receiving end
-
Product
Optical Laser Source Products
-
Tunable Laser Source, Compact Tunable Laser Source, Fabry-Perot Laser Source Modules and Distributed Feedback Laser Source Modules.
-
Product
LED Goniophotometer For Led Tester
CX-880
-
Shenzhen Chuangxin Instruments Co., Ltd.
880 LED Test machine is used to measure: 1.the luminous intensity dirstribution curve, 2.intensity data, 3.spread angle and equivalent luminous flux of small lamps.
-
-
Product
Bench-top Optical Light Source
STC-BTOLS2201 series
-
Shanghai Stone Communication tech Co., Ltd
STC-BTOLS2201 series high stable Bench-top light source are microprocessor controlled laser diode sources which can support the variety of emitters such as: DFB,FP,PUMP,SLED etc. It is specially used in passive components testing, power meter calibration and general laboratory uses.
-
Product
Chemical Downstream Plasma Source
-
The AX7610 is a microwave plasma source for remote plasma applications. With replaceable quartz or sapphire plasma tubes, the AX7610 downstream source offers configuration flexibility to meet the most demanding application process parameters. The quartz tube version is ideally suited for production of atomic oxygen, nitrogen or argon. The sapphire tube version is compatible with much more severe CF4 CHF3 and NF3 chemistries.
-
Product
Source to Object Code Analyser
RTT-STO
-
Verified Systems International GMBH
RTT-STO is a software analysis tool-suite that automatically performs static program analyses of C code and assembly required to receive certification credit for source-to-object code validation in the context of safety-critical avionics software.
-
Product
Gridded DC Ion Sources
-
Ion-assisted processes like sputtering, etching, and surface treatment depend on a beam that’s stable, uniform, and tightly controlled. Gridded DC ion sources make that happen, giving engineers the precision they need to fine-tune ion energy and current density for reliable results.
-
Product
Optical Laser Source
SAT-3E
-
Shaanxi Aitelong Technology Co., Ltd
SAT-3E optical laser source fits to optical power meter to measure fiber loss and evaluate transmission performance. They are indispensable tool for optical network installation, trouble shooting, maintenance and widely used in LAN, WAN, CATV, remote optical network, etc.
-
Product
Light Source
UVF-204S
-
This is the ultra compact and light weight high power unit fully utilizing characteristics of the high stability and long life 200watt mercury xenon lamp.
-
Product
Optical Light Sources
-
A fiber optic source is commonly used with a meter to measure optical fiber attenuation or insertion loss.
-
Product
High Speed LED Pick And Place
MCLEDV6
-
Assemble LED lighting products, including long tube boards and flexible strips, at rates reaching 30,000 LEDs per hour, with a high-speed, dedicated LED placer. The MCLEDV6 has a 23.6" (600 mm) max board length and includes automatic, on-the-fly full vision alignment.
-
Product
SLD Light Source
-
The SLD light source is a light source to emit low-coherence light with a broad spectrum like LED and high brightness like LD. Light emitted from a narrow active layer like LD effectively couple to the fiber. SLD light source can be used for optical measurements and sensors, including fiber optic gyroscopes and OCT. FiberLabs provides fiber-output SLD light sources in different wavelength bands from visible to near-infrared light. Our lineup includes bench-top types convenient for experiments and easy-to-integrate module types.
-
Product
Four-Wavelength Laser Source
CA6017 Series
-
The CA6017 Can transmit with a wavelength-identification digital encrypted protocol, enabling the FHP2 power meter to automatically use the proper calibration wavelength. This feature reduces the need for communication between the two technicians and decreases the possibility of making mistakes
