Memory Device
directly accessible computer's internal or main memory.
See Also: Memory, Memory Test, DDR, NAND, DRAM, RAM, ROM, Memory Testers, DUT
-
Product
Patented GPS Jamming and Spoofing Detection Embedded in Your Device
BroadShield
-
PNT systems are designed to provide accurate position and time while in uninterrupted or uncontested environments. However, while in these interrupted or contested environments, most PNT systems are unable to reliably provide position and time data because they are unable to recognized what is causing the disruption. BroadShield is a software library consisting of many patented algorithms designed to detect jamming and spoofing then immediately report the disruption to the PNT system. Leveraging this information enables the PNT system to take action to mitigate and protect from the jamming or spoofing.
-
Product
Voltage Input Device For FieldDAQ
-
The Voltage Input Device for FieldDAQ measures up to eight ±10 V channels with 24-bit resolution and simultaneous sample rates up to 100 kS/s/ch. Some models can power sensors, such as pressure sensors, with up to 24 V per input channel. This device offers 500 V channel-to-channel isolation, protecting instrumentation from high-transient voltages. Additionally, the device is IP65 and IP67 rated to be dust-proof and water-submersible, can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. It has an integrated network switch for simplified daisy chaining and provides tight synchronization over time sensitive networking (TSN) for distributed data acquisition systems.The Voltage Input Device for FieldDAQ includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Programmable Serial Device
HR-16P
-
The HR-16P is a programmable RS-232 serial device designed to control any device with a serial port based on sensing level changes (open-to-close and close-to-open, or digital high to low and vice versa).
-
Product
Laser Hunter - gas detection & gas measurement device
-
Highly sensitive and selective gas detection & gas measurement device withlaser technology for the inspection of underground gas pipes using suitableprobes (e. g. carpet probe). The device can also be used for the vehicle-basedpipeline inspection.With built-in diaphragm pump, Bluetooth module and rechargeable Li-Ion battery.The following applications are possible:- Inspection of underground pipes- Inspection of accessible pipes in buildings- Inspection of accessible pipes on plants, etc.- Inspection of ground soil for pinpointing (optional)- Purging of gas pipelines (optional, only in combination with pinpointing)- Gas analysis (with dual laser module)
-
Product
PCIe-8431, PCI Express, 8-Port, RS485/RS422 Serial Interface Device
780592-01
Serial Interface
The PCIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between … 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Flash Memory In-System Programming File Generation
ScanExpress Flash Generator
-
ScanExpress Flash Generator is a tool to quickly create Flash programming files for use with ScanExpress™ software. The application operates as a standalone utility or integrates into ScanExpress TPG for creation and reuse of boundary-scan test files for in-system programming (ISP).ScanExpress Flash Generator combines a board Netlist, scan chain description, and BSDL files to automatically create Flash Programming Information (FPI) files. These files include all information necessary for ScanExpress Runner™ or ScanExpress Programmer™ execution systems to perform read, write, erase, and verify operations—in-system using high performance Corelis hardware.
-
Product
RS232 RS485 RS422 Serial To Ethernet Modbus Converters / Device Servers
-
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and flexibility. CommFront offers a range of industry-proven, easy-to-use serial to Ethernet converters and device servers, both hardware and software types. The applications of our serial to Ethernet converters include acting as a device server or a Modbus RTU/ASCII to Modbus TCP protocol converter; extending serial ( RS232 / RS485 / RS422 / TTL) communication distance over Ethernet network; controlling serial devices from remote Modbus TCP software or Modbus RTU master via Ethernet network; making a wide variety of M2M communication applications possible by enabling client access independent of any operating system or proprietary protocol; and converting conventional serial data network into TCP/IP network, etc.
-
Product
USB Device Server
-
Advantech USB serial device server allows PC users to connect serial devices via a LAN to systems. They allow access from anywhere on your network.
-
Product
Digital I/O Device
Digital I/O
The Digital I/O Device supports channel, current, and voltage options to help you automate applications. This module features programmable input filters to remove chatter, noise, glitches, and spikes on inputs, and these filters also provide debouncing for digital switches and relays. You can use the module to perform safe operation when connected to pumps, motors, and other industrial actuators or machinery using the included power-up states. The module also provides a fail-safe mechanism that monitors for computer or application crashes and place the system in a state to ensure safe recovery. Additionally, some models include high-voltage, high-current, and isolation options to ensure the product can work safely in many environments.The Digital I/O Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
16-Bit PCIe Gen-2 Digitizer / Oszilloscope 4 Channel 25 MS/s Up To 8 GS Memory
Octave-16 Express / CompuScope 8442
-
The GaGe Octave Express 84XX CompuScope PCIe digitizer card features 16-bit resolution with sampling rates up to 25 MS/s with true Effective Number of Bits (ENOB) of 12-bits with 10 MHz input. Onboard digitizer sample memory is expandable up to 8 GS (16 GB) and up to 8 Octave Express digitizers can be combined for up to 32 channels in a single system.
-
Product
GPIB-RS232, Instrument Control Device - United States 120VAC
779732-01
GPIB Controller
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a … talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
MRAMs - Magnetoresistive Random Access Memory
-
Teledyne e2v’s MRAMs type EV2A16A is an extended-reliability version of the MR2A16A from Everspin. It is the ideal memory solution for applications that must permanently store and retrieve critical data quickly. It perfectly suits the requirements of critical embedded applications such as avionic, aerospace and defence environments.
-
Product
PCI-5412, 100 MS/s, 14-Bit Waveform Generator Device
779177-01
Waveform Generator
The PCI‑5412 can generate user-defined, arbitrary waveforms and standard functions, including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms.
-
Product
Measuring Device for Testing the Effectiveness of Residual Current Protective Devices (RCD) According to DIN EN 61557-6 (VDE 0413-6)
-
PeakTech Prüf- und Messtechnik GmbH
A residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE).
-
Product
Active Device Characterization Solution Up To 67 GHz
N5247BM
-
The N5247BM provides the N5247B 67 GHz PNA-X network analyzer, application software and accessories for active device characterization up to 67 GHz.
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785324-01
Interface
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786163-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Ultra Fast Digitizer With 8 Bit, 4 GS/s Sampling Rate With Up To 8 GS Memory
CompuScope Express 14G8
-
The CobraMax CompuScope family of GaGe ultra high-speed 8-bit digitizers provides the most powerful combination of speed, memory, and bandwidth as well as a wide portfolio of advanced acquisition features on a single PCI Express or PCI card.
-
Product
PCI-5124 , 150 MHz Bandwidth, 200 MS/s, 12-Bit PCI Oscilloscope Device
779171-02
Oscilloscope
150 MHz Bandwidth, 200 MS/s, 12-Bit PCI Oscilloscope Device—The PCI-5124 high-resolution oscilloscope device has two channels that sample up to 200 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution measurements with up to 150 MHz of analog bandwidth.
-
Product
Automated Hipot Accessory Device
CX-K12
-
Shenzhen Chuangxin Instruments Co., Ltd.
Purpose, To test thin insulating materials for dielectric voltage withstand strength when connected to a hipot tester.
-
Product
Measuring Device For Measuring Residual Magnetism
Teslameter M-Test LL
-
Measure residual magnetism on ferromagnetic materials precisely and reliablyquick detection of residual magnetismreproducible measurement results through automatic storage of the maximum valuesdefined measuring distance of 0.5 mm from the Hall probe to the measuring surfacemeasuring static and alternating magnetic fieldsselectable units: A / cm, Gauss, mTwear-resistant test sample
-
Product
Qseven V1.2 SoM With I.MX287 454 MHz (Industrial) SoC, 128MB Memory, 4GB EMMC, Gigabit Ethernet, Audio And CAN
Q7M100
-
*Ultra low power consumption ARM9*High flexibility Qseven v1.2 compliant design*2 CANBus 2.0B compliant ports*24-bit TTL LCD*Dual 10/100 Base-T Ethernet*Audio
-
Product
System Devices for Radiomonitoring
-
Monitoring stations need auxiliary equipment to ensure optimal alignment and control of the antenna or antennas or to provide users with RF signal filtering functions close to the antenna, depending on requirements. Customers around the world use the innovative system devices for monitoring stations from Rohde & Schwarz to meet these requirements. These devices stand for performance, quality, flexible deployment options and a wide range of possible configurations, which is why they are an optimum solution for any radiomonitoring application when used in conjunction with the other products in the Rohde & Schwarz radiomonitoring and radiolocation portfolio.
-
Product
The All In One Instrumentation Tool For K-Series Devices
K-Cal
-
K-Cal is freely distributable and supports all K-series instrumentation modules.
-
Product
Acute 2GHz, 34 Channel, TravelLogic Series Protocol & Logic Analyzer With 8Gb Memory
Acute TL3234B+
-
The TravelLogic Series of Protocol & Logic Analyzers are small enough to fit into your shirt pocket, yet are truly sophisticated logic analyzers, capable of 2 GHz timing analysis, or 200 MHz state analysis, with up to 8 Gb total stackable memory for the 34 channels. They plug into a PC or Laptop USB port making them ideal for the field service technician or engineer, hopping from PC to PC, or taking with them for diagnosis on the road. Also remember that with USB, no additional power supply is needed.
-
Product
Reflective Memory Analyzer
PEAZ-5565
-
Abaco Systems' PEAZ-5565 Reflective Memory Analyzer is a powerful analytic tool for the industry-leading 5565 Reflective Memory (RFM) product family. By creating a window into network traffic, the analyzer allows you to deep dive into your application code to start solving problems.
-
Product
PCI-6111, 2 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device Multifunction I/O Device
777530-01
Multifunction I/O
2 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6111 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6111 is ideal for a variety of applications, such as … stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6111 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
Thyristors Application Specific Devices
-
A.S.D. (Application Specific Discretes) technology is a vertical integrated power technology using a full planar process. By applying the masking process on both sides of the chip, higher current density is achievable than is possible with epitaxial base or horizontal structures.
-
Product
USB-4065, 6½-Digit, ±300 V, USB Digital Multimeter Device
780152-01
Digital Multimeter
The USB‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
Machine Vibration Monitoring Devices & Systems
Spider-80x
-
*Route Based Vibration Data Collection*Remote Condition Monitoring Software*Vibration Diagnostics System
