Product

Probes

-

OAI

OAI

220-540nm Probes by OAI

Product

Software

DIGITIZER

-

Digitaltest GmbH

DIGITIZER - Digitaltest GmbH

The Digitizer allows the recovery of design data of unknown assemblies by an electrical analysis with a Condor flying probe test system

Product

MOD MONITOR

TYPE HFX-1

-

National RF, Inc

TYPE HFX-1 - National RF, Inc

The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.

Product

Vertical Probe Cards

B3

-

Nidec SV Probe Pte. Ltd.

B3 - Nidec SV Probe Pte. Ltd.

The patent-pending B3™ structure requires a minimum number of parts and can handle up to 300 probes. This vertical technology can provide: • Increased Uptime • Extended Probe Lifetime • Reduced Maintenance • Lower Cost of TestThe B3™ is an ideal solution for testing small pads and the low force probes minimize scrub. Planarity also remains stable over time increasing probe card life. Contact your sales representative to learn more about our B3™ probe cards.

Product

Local Discomfort Temperature Probe

TP3227PC

-

Senseca

TP3227PC - Senseca

Temperature probe composed of 2 independent probes, Pt100 sensor, used for measuring local discomfort due to vertical thermal gradient.

Product

High Speed Contacts

-

Smiths Interconnect

Smiths Interconnect

Our  quadrax, twinax, spring probe, coax, triax and fiber optic contacts can be sold seperately or configured into any of our standard connector shells sizes as well as cable assemblies and harnesses.

Product

7.5 GHz Low Capacitance ÷10/÷20 probe

PP066

-

Teledyne LeCroy

PP066 - Teledyne LeCroy

The PP066 is a high-bandwidth passive probe designed for the use with the WaveMaster™ and other high-bandwidth oscilloscopes that have 50 Ω input termination. This very low capacitance probe provides an excellent solution for higher frequency applications, especially the probing of transmission lines with 20–100 Ω impedance.

Product

Needle Microprobe

MT-29/3HT

-

Physitemp Instruments

MT-29/3HT - Physitemp Instruments

Fast-response 29 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.

Product

Cylinder type, Near field Antenna Measurement System

anm02

-

KEYCOM Corp

anm02 - KEYCOM Corp

As it combines the vertical direction of the probe antenna with the turn of the object antenna, and performs the near field measurement in the shape of a cylinder. The result will be converted to far field. Feature The pattern behind the antenna can be measured by a cylinder scanning. Fast measurement.For example ) Vertical direction 256 point and Rotatory direction 180 point : 30 minutes.

Product

Microwave Testing

10

-

Picoprobe

10 - Picoprobe

PICOPROBE® MODEL 10 is a multipurpose, high speed, passive probe which can be used for driving as well as receiving signals. The Model 10 consists of a one meter length of flexible 50 ohm coaxial cable terminated by a carefully trimmed SMA on one end and by a miniature, high speed 50 ohm connector, specially developed to receive Model 10 replaceable coaxial probe tips, on the other. The 50 ohm coaxial cable was custom designed for Model 10 to be high speed, yet very flexible, so that moving the cable would not disturb the probe points.

Product

DL-HCM Series Accessories Kit with Probe Holder, Micro IC Grabbers (Qty. 2), and Y-Banana Adaptor

DL-HCM-Acc-Kit

-

Teledyne LeCroy

DL-HCM-Acc-Kit - Teledyne LeCroy

60 V of common mode and 80 V differential input range with 1 GHz of bandwidth, make these probes ideal for lower voltage GaN power conversion measurements. The 60 V of common mode is well suited for handling any float of the battery and bulk/absorption voltage during charging, while the 80 V differential input range provide margin for any overshoot.

Product

TRMS Digital Multimeter

HT65

-

HT Italia Srl

HT65 - HT Italia Srl

HT65 belongs to the TRMS CATIV 600V series of digital multimeters, made unique by the ability to measure DC voltage up to 1500V. It is also able to measure the temperature through the K probe, the AC / DC current with an external transducer, and the LoZ low impedance voltage input.

Product

Probe Tip Ground Lead with Alligator Clip

PK007-025

-

Teledyne LeCroy

PK007-025 - Teledyne LeCroy

Probe Tip Ground Lead with Alligator Clip.

Product

Flying Probe Test System

A8a

-

Mycronic

A8a - Mycronic

The A8a test system provides the flexibility of flying probe testers while delivering high throughput testing for bare board printed circuit boards (PCBs). The target market for the A8a is the electrical test of tablet and PC motherboards and high density interconnect (HDI) products for smart phones. The A8a is designed for high productivity, reliability and test accuracy. To achieve high throughput the key feature of the A8a is a new dual shuttle system, which reduces the product exchange time to zero seconds in automation mode. In combination with the fast test speed of up to 140 measurements/second the A8a will give customers a competitive test solution for batches up to 5000 boards. A typical cycle time of a 4-up smart phone board is about 2 minutes.

Product

Benchtop Discrete Component Tester

Imapact 7BT

-

Lorlin Test Systems

Imapact 7BT - Lorlin Test Systems

The 7BT Benchtop Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The 7BT automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability.

Product

Microscope Spectrophotometer

508 PV

-

CRAIC Technologies

508 PV - CRAIC Technologies

The 508 PV™ Microscope Spectrophotometer is designed to add spectroscopy, color imaging, thin film thickness measurement and colorimetry capabilities to your optical microscope or probe station. It can also be used to upgrade an older microspectrometer with cutting edge optics, electronics and software.

Product

Reference Meters

-

ThermoWorks

ThermoWorks

Whether standard or high precision, ThermoWorks handheld meters feature rugged housing and best-in class accuracy across a variety of temperature ranges. Choose from integrated systems or meters that accept multiple probes, single or dual channel meters, alarms or reference models. Perfect for BBQ or sous-vide applications, dairy processing and meat processing, pharmaceutical labs, concrete curing, health departments, and for line checks, critical control point management, and HACCP checklists.