-
product
Optical SpO2 Pulse Oximeter Simulator
OX-1 OxSim®
Test the complete SpO2 system, including the sensor, extension cable with the OxSim® Optical SpO2 Pulse Oximeter Simulator. Slips into your shirt pocket and operates easily with just two buttons on a single AA battery. The auto-detection of the Sensor type eliminates the need to select the manufacturer oximeter under test. The optional serial communications port enables users to expand simulation settings for Saturation, Pulse Rate, and Perfusion Index, ideal for applications where a wide range of simulations is needed.
-
product
One Wire Communication Board
MS 1727
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
product
Solid State Broadband High Power Amplifier
Model 2215
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
product
Pulse Signal Amplifier
VCH-606
The pulse signal amplifier VCH-606 is designed to multiply a single pulse or a sequence of pulses to 16 independent outputs. The impulse signal amplifier includes 16 independent channels with unity gain each for connecting consumers of impulse signals with an input impedance of 50 Ohm.
-
product
Advanced 8-Axis Servo & Stepper Motion Controller with Modular Design
PCI-8158
The PCI-8158 delivers high-frequency pulse rates of up to 6.55 MHz and features hardware-controlled emergency input stop, software security protection to avoid plagiarism, card index switch, and linear/circular run at the same time for that exceed the industry"s cost over performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and steppers, the PCI-8158 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuo...show more -
product
Ultrafast Transient Absorption Spectrometer
Harpia-TA
The transient absorption spectrometer HARPIA offers a sleek and compact design together with intuitive user experience and easy day-to-day maintenance meeting the needs of today's scientific world. Adhering to the standards raised by the OPRHEUS line of devices, the entire spectroscopic system is contained in a single monolithic aluminum casing that inherently ensures excellent optical stability and minimal optical path for the interacting beams. HARPIA can be easily integrated with both PHAROS ...show more -
product
Pulser / Sampler Core
Furaxa has researched, developed, and characterized a novel monolithic arrayable pulse and sample aperture generation technology. Recent results include demonstration of sub-10ps pulse/aperture generation at repetition rates up to 3 Billion Pulses/Samples Per Second (BPPS) with jitter that is estimated at sub-10fs. Further, simulations in a number of InP DHBT processes exhibit sub-3ps 20BPPS performance. The IP is process-independent, and has been achieved in CMOS SOI, InP HBT, SiGe and GaAs so ...show more -
product
USB Modular Function Generator
U2761A
Keysight U2761A is a 20 MHz function generator that offers 10 standard waveforms plus pulse and arbitrary waveforms generation capabilities.
-
product
Ultrafast Laser Pulse Measurement
FROG Scan
Our FROG Scan system is versatile, adaptable and easy to use. With our FROG Scan, you can tweak a laser system or measure highly chirped pulses to calculate the amount of dispersion compensation you might need for recompression. Measure a short pulse that has been chirped out to several picoseconds, or measure pulses as short as 12 fs in real-time.
-
product
Torque Meter for TQ-3507 High-Stiffness Torque Detector
TQ-5300
TQ-5300 Torque meter, used with the TQ-2000 series High-stiffness torque detector, can convert the pulse output of the detector to digital torque value and analog voltage output.
-
product
Impulse Generators
HYPERLABS triggerable impulse generators create precise high-speed pulses with 50 to 100 ps rise time. They can be triggered by input from antennas and other signal generator systems.
-
product
RF Safety Monitoring
MVG EME Guard XS Radar
Specifically designed to alert workers operating near radar transmitters of RF exposures, the unique EME Guard XS Radar is an RF pulse measuring device. It continuously scans for short pulsed signals, and via its built-in alarm and visual system, alerts users whenever the acceptable limits have been exceeded. This RF Safety tool is extremely easy to use and creates a safer working environment close to radar antennas and other pulsed RF sources.
-
product
Optical Chopper
These high stability variable frequency optical choppers each include a set of chemically blackened photoetched chopping discs. The mini chopper is an excellent choice for applications requiring a compact package. The chopping discs come in a variety of slot apertures and allow operation. Beam diameter is limited to 0.75mm when using the 200-slot disc and 1.0mm when using the 40 slot mini disc. The easy-to-interchange blades are made of non-magnetic, half hard brass and can be used in combinatio...show more -
product
Amplifiers
We have designed and manufactured amplifiers using all major semiconductor materials, LDMOS, GaN, GaAs, and InP, to produce narrow, wideband, and pulse, receive and transmit amplifiers from 1 MHz to 220 GHz and power levels from mW to over 10 kW.
-
product
Advanced 8/4-Axis Servo & Stepper Motion Controllers With Modular Design
PCIe-8158
The PCIe-8158 delivers high-frequency pulse rates up to 6.55 MHz and hardware-controlled emergency stop, software security protection, card index switching, and simultaneous linear/ circular run, exceeding industrial cost/performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and any pulse-train controlled servo and stepper drives, the PCIe-8158 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous cont...show more -
product
High Voltage 50 Ω Pulse Generator
TLP-8010A
High Power Pulse Instruments GmbH
*Wafer and package level TLP/HMM testing*Fast 50 Ω high voltage pulse output with typical 300 ps rise time*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω-configuration*High pulse output current up to ±80 A (short circuit) with 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 300 ps to 50 ns*1 built-in pulse width: 100 ns*Optional external pulse widt...show more -
product
Low Leakage Switch Mainframe
B2201A
The B2201A reduces the cost of test by enabling characterization tests to be automated, with only slight compromise to the measurement performance of the semiconductor parameter analyzer. It supports a 4-SMU, full-Kelvin configuration and a capacitance meter, with room for future expansion. Includes 14 inputs, each with a unique internal measurement path, and a distinctive capacitance measurement compensation feature for two of the inputs. Provides front panel control via keypad or optional light pen, and supports instruments such as pulse generators.
-
product
Pulse Panel Meter
PPM
The Series PPM has a unique, rugged, NEMA 4X front panel design that makes it nearly impenetrable in typical applications. The weatherproof, UV resistant, large, dual line display allows for more information, making it easier to read and simpler to program. The intensity of the display can be adjusted allowing this meter to be utilized in dark rooms as well as outdoors, due to its sunlight readable display.
-
product
Field Strength Meter
FIM-71 VHF
The Model FIM-71 is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-71 is suitable for practically all types of RF emission measurements in the 45 MHz to 225 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and a meter dynamic range of...show more -
product
LED solar simulators
We offer innovative A + A + A + LED solar simulators for the integration of the production process and for the stand-alone operation in the laboratory or goods receipt. Our LED solar simulators are characterized by maximum repeatability, a long pulse duration and very low maintenance.
-
product
High-voltage Power Supplies
Communications & Power Industries
The CPI TMD high-voltage power supplies offer many features desirable for modern radar and electronic warfare applications: high efficiency, ultra-low voltage ripple (low noise), high inverter frequencies, ultra-low pulse-to-pulse jitter, low throughput delay and high power density. The units are lightweight and compact with excellent thermal management, and the high-voltage sections are encapsulated with an oil-free, silicone-based compound. This provides excellent protection in harsh environments while also enabling easy maintenance.
-
product
Fluorescent Lamp Asymmetric Pulse Tester
UI2002C
UI2002C is designed according to the latest update in IEC 61347-2-3 about the test requirements for local rectifying effects on tubes. It imitates the condition when tube is under local rectifying status and tests the abnormal protection function of ballast by adopting fluorescent lamp asymmetry pulse test method with 3 windows for displaying rectified voltage, rectified current, and rectified power. It is easy for operation and with high test accuracy. • Measure lamp voltage, lamp current , average and total power of lamp. • Lamp voltage range: 10~300V • Lamp current range: 10mA~1.0A • Lamp power range: 0.5~300W • Tolerance is 5%
-
product
Arbitrary Waveform Generator
SDG7000A
SIGLENT’s SDG7000A is a family of dual-channel Arbitrary Waveform Generators that feature up to 1 GHz bandwidth, a maximum sample rate of 5 GSa/s, and 14-bit vertical resolution. It can generate arbitrary waveforms point by point with a maximum 2.5 GSa/s sample rate and vector signals with a maximum of 500 MSa/s. It also has the ability to generate a variety of signals such as continuous wave, Pulse, Noise, PRBS patterns, and a 16-bit digital bus. It supports the generation of complex signals su...show more -
product
Multi-Battery Tester
MBT-1
The ZTS Multi-Battery Tester (MBT-1) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
product
Integrated Potentiostat System
ER466
The ER466 Integrated Potentiostat System is our most popular potentiostat model, being ideal for cyclic, linear sweep, and most analytical pulse voltammetric experiments, either in the research or teaching laboratory. It also functions as a galvanostat, ZRA (zero resistance ammeter), and high impedance voltmeter (electrometer).
-
product
Network Analyzers
MPR6 Series
Dimensions:96X96kVArh, Max, Min: available (available) % THD I: available (available) % THD V: available (available)Harmonics 1-51.:RS-485:available (available)Digital Input:Digital Output:2AO:0/14-20mA: AO:0/2-10V:Relay:2 Pulse Output: available (available) Hour (RTC): available (available) Memory:1MB Pulse Counter: none (none) Operating Hour: none (none) Alarm: available (available) CT-25: none (none) 110/230 VAC:none (none) 85-265 VAC/DC: available (available) 45-265 VAC/DC: none (none) 10-56 VDC: none (none) Pcs. / Carton:8
-
product
Primary Cable Fault Locating
Directional Impulse Detector
The Directional Impulse Detector ( D.I.D.) is a compact handheld detector used to locate primary cable faults by sensing the magnetic field generated by the current pulse from a high voltage discharge device (thumper). A meter deflection indicates the intensity of the received signal. No deflection indicates that you have walked beyond the fault or away from the cable.
-
product
Counter/Timer Board
USB-CTR-15
The USB-CTR-15 is an ideal solution for adding portable, easy-to-install, counter/timer capabilities to any PC or embedded system with a USB port. This board is packaged in a small, rugged, industrial enclosure and features 15 independent 16-bit counter/timers. The unit is a true USB 2.0 device, offering the highest speed available with the USB bus. It is fully compatible with both USB 1.1 and USB 2.0 ports. The unit is plug-and-play allowing quick connect/disconnect whenever you need additional...show more -
product
Pulse/Arbitrary Waveform Generator
SDG6000X Series
Dual-channel Pulse/ Arbitrary Waveform Generators that feature up to 500 MHz bandwidth, a maximum sample rate of 2.4 GSa/s and 16-bit vertical resolution. They also include proprietary TrueArb & EasyPulse technology that help to solve the weaknesses inherent in traditional DDS generators when generating arbitrary, square and pulse waveforms. In addition, the SDG6000X is a multi-function device which can generate Noise, IQ signals and PRBS patterns. These features enable the SDG6000X to provide a variety of high fidelity and low jitter signals, meeting the growing requirements of complex and intensive applications.