-
product
SpikeSafe DC / Continuous Pulsed Current Sources
The Vektrex SpikeSafe™ DC / Continuous Pulse (DCP) Current Sources provide reliable DC or pulsed drive for LED or laser diode reliability testing, IESNA LM-80 maintenance testing, and other test applications requiring DC or continuous pulse current. Models support currents from 500mA to 60A and compliance voltages from 50V to 400V. All models feature individual channel control, accurate pulsing over long output cables, precise current, precision pulsing for improved measurement repeatability, and high power density — typically 6.4kW-8kW.
-
product
C Series Counter Input Module
The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, and counter measurements in your chassis.The C Series Counter Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Lightning Surge Generator
SKS-0510I
Shanghai Sanki Electronic Industries Co., Ltd.
The lightning surge generator SKS-0510I fully complies with the new standards of IEC61000-4-5, EN61000-4-5 and GB/T17626.5; it provides pulse test voltages up to 10kV, which can meet the severity levels of various product standards; Covers the two surge waveforms specified in the standard 1.2/50ms (short-circuit current is 8/20μs) and 10/700ms (short-circuit current is 5/320μs), and a variety of internal resistances are built-in for customer use; Two kinds of surge waveforms, and built-in a variety of internal resistances for customers to use; AC and DC samples can be tested, the rated current can reach 32A.
-
product
P-Series Single Channel Power Meter
N1911A
30 MHz video bandwidth Single shot real time capture at 100 M sample/s per second Key Measurements: - peak, average, peak-to-average ratio, rise time, fall time and pulse width22 Predefined formats: WiMAX, DME, HSDPA, etc. One screen view for pulse measurement analysis: Auto Scale, Auto Gate, Rise/Fall Time, Duty Cycle, etc. Internal Zeroing and Calibration while connecting to the DUT Bench Vue software enabled
-
product
Programmable Low-Ohm Meter
DU5210/5211
Delta United Instrument Co., Ltd.
20m ~ 2Mtest range, 0.1% accuracy Provided Level and Pulse measurement modes, can be lower temperature influence in Pulse Mode Provided HI/LOW limit and BIN Sorting comparator function, to meet your needed 100 sets of memory, can be saved test parameter and comparator setting, easy to use. Auto Calibration Program Function, to easier your calibration procedure. (Specificity calibrator needed) Cover up free, system firmware upgrade can be update via RS-232, easy to maintenance High speed FADC, max. test speed up to 80 meas./sec, faster your automation equipment 240*64 Graphic LCD display, can be read the reading clearly and easier. User friendly programmable interface, easy to use Provided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
Wall-Mounted Electronic Energy Meter
MWH-7W
The MWH-7W series is an electronic energy meter with excellent performance, the main function is high-precision energy metering, the panel has LCD display, the energy value is clear and easy to read. The power meter provides functions such as pulse output and RS485 communication interface, which is convenient for the user to check or structure into a centralized meter reading system.Panel and wiring cover with lead seal, in accordance with CNS 14607 specification design.
-
product
Defibrillator Analyzers, Pacemaker Testers and AED Testers
Fluke Biomedical’s defibrillator analyzers and defibrillator/transcutaneous pacemaker testing devices are rugged, portable precision test instruments that ensure proper operation and ultimate performance of critical life-support cardiac-resuscitation equipment. We offer best-in-class defibrillator testers that feature capabilities which encompass a wide spectrum of worldwide established pulse shapes, showcasing AED tester compatibility, and outperforming competitors in accuracy and standards.
-
product
6-Channel VME Buffered Electrical-to-Optical Converter
V720
The V720 is a six-channel logic-level electrical-to-optical converter, packaged as a single-width, 6U VME module. It may be used with compatible Highland optical receiver modules for fast, low-jitter, EMI-proof distribution of pulses, triggers, and precision timing signals.
-
product
High-voltage Power Supplies
Communications & Power Industries
The CPI TMD high-voltage power supplies offer many features desirable for modern radar and electronic warfare applications: high efficiency, ultra-low voltage ripple (low noise), high inverter frequencies, ultra-low pulse-to-pulse jitter, low throughput delay and high power density. The units are lightweight and compact with excellent thermal management, and the high-voltage sections are encapsulated with an oil-free, silicone-based compound. This provides excellent protection in harsh environments while also enabling easy maintenance.
-
product
PSG RF Analog Signal Generator, 100 kHz to 9 GHz
E8663D
Tackle demanding radar & satcom measurements with metrology-grade performance, including high output power & superior level accuracyUse as an ideal reference in phase noise test systems or for analog-to-digital converter testing with the lowest phase noise in a commercial sourceCharacterize devices & circuits by adding AM, FM, M & pulse modulation to your signalImprove existing test system performance: E8663D is built on the outstanding legacy of the 8663A & is fully code compatible
-
product
High Power Fiber Laser
Amonics' Fiber Laser (AFL) is a compact standalone turnkey equipment to deliver up to 50W output power and 1mJ pulse energy in 1064nm and 1550nm range under CW or pulse operation. Based on proprietary all fiber design, Amonics fiber laser is maintenance free. No post-installation service is required.In pulse operation, the laser delivers up to 20kW peak power and adjustable pulse width from 10ns to 1000ns. The pulse repetition rate is triggered by external TTL signal.Amonics fiber lasers are the ideal candidate for a wide range of industrial applications.
-
product
NanoModeScan M² Measuring System
This scanning slit M² measurement system accurately analyzes lasers with wavelengths from UV to Far Infrared with its silicon, germanium, or pyroelectric head. It features a compact portable design, immediate results, ISO compliant measurements, and operates in CW or kHz Pulsed modes which makes it ideal for comprehensive analysis of lasers of most wavelengths.
-
product
Pulsed Lasers and LEDs
PicoQuant's compact and reliable turn-key diode laser solutions work in picosecond pulsed, modulated, or fast-switched (nsec to µsec) operation mode. The laser systems typically consist of a common driver unit and exchangeable heads. Specialized lasers are also available as stand-alone units.
-
product
PCI-6624, Isolated 48 VDC, 8-Channel Counter/Timer Device
778834-01
The PCI‑6624 performs a wide variety of counter/timer tasks, including event counting, time period/frequency measurement, quadrature encoder position measurement, pulse width measurement, pulse generation, and pulse train … generation. Example applications also include generation of retriggerable pulses, two-signal edge separation measurements, continuous buffered event counting, and continuous buffered pulse train measurements. The PCI‑6624 offers superior industrially rugged features for a wide array of applications such as automotive/aerospace, industrial/motion control, and manufacturing test.
-
product
*Photodiode Energy Sensors
Ophir photodiode laser energy sensors are able to measure low energy pulses down to 10pJ at frequencies up to 20 kHz. Silicon photodiodes for the UV and visible spectrum and Germanium photodiodes for infrared.
-
product
Transmission Line Pulse Testing
Transmission Line Pulse testing, or TLP testing, is a method for semiconductor characterization of Electrostatic Discharge (ESD) protection structures. In the Transmission Line Pulse test, high current pulses are applied to the pin under test (PUT) at successively higher levels through a coaxial cable of specified length. The applied pulses are of a current amplitude and duration representative of the Human Body Model (HBM) event (or a Charged Device Model – CDM – event in the case of Very Fast TLP, or VF-TLP).
-
product
Photodetectors
Packaged photodetectors based on PIN photodiodes for monitoring Q-switched and mode-locked pulsed lasers.
-
product
Synthesizer Up To 140 GHz
Insight Product Company offers a high-power synthesizer of pulsed signals. They are ideal for ESR, EPR, and DNP experiments. The synthesizer has a high frequency stability (10-6), and allows control over the duraction and begining time of pulses. The synthesizer also enables phase manipulation, where each pulse is shifted by 90 or 180 degrees relative to the previous pulse.
-
product
P104 Synchro/Resolver Measurement Board
73SD4
NAI’s 73SD4 is a DSP-based, PC104-compliant Synchro/Resolver Measurement Board with six separate, isolated channels. These channels can incorporate up to six Synchro/Resolver-to-Digital Tracking Converters in a stack-through module. Each channel also produces differential incremental encoder (A & B) outputs (with programmable resolution) and a zero-degree marker pulse. Commutation outputs are available for 4-, 6-, or 8-pole brushless DC motors that eliminate the need for Hall Effect sensors, thereby reducing both processor time and bus traffic.
-
product
Modbus Transducers
THI Sensors
The THI-485 sensors are Modbus transducers for measuring thesurrounding temperature and relative humidity or for theacquisition of up to four passive pulse signals or digital states. This feature extends the possibilities of the device, turning it into a kind of RS485 pulse concentrator from other sensors andmeters.
-
product
*Picosecond Lasers
A revolutionary laser technology due to its much shortened pulse duration of just 1012 seconds.
-
product
2-18GHz Switch Multiplexer
SA002
Teledyne Defence & Space’s (TDS) patented designs have produced many different types of filters incorporating switches. These are all generally wideband for Electronic Warfare applications and enable the control of the frequency spectrum into any given system. These units, also known as Switch Multiplexers, are configured with a single or multiple inputs to single or multiple filtered outputs.As an example, the SA002 features 8 channels switchable over the frequency range 2-18 GHz while the SA004 offers 17 channels over the 0.5-18GHz bandwidth. Each provides the user with a fast, flexible, filter network capable of providing different band-pass or band-stop responses on a pulse-by-pulse basis in dense signal environments.
-
product
TX Ranger
4405200
The TX Ranger is a hand-held Time Domain Reflectometer (cable fault locator) with a first range of 2.5 meters combined with a 1.3 Nano second pulse width gives a blind zone of only 5 cm, it makes this the ideal product for fault location on short cable assemblies and harnesses. Small and intermittent faults can be easily identified by using the selectable gain control allowing trace amplification of up to 7 times and when set to scan lock mode the advanced noise reduction software may be selected allowing the user to select between 8,16 and 32-point trace averaging further enhancing the clarity of the trace by reducing electrical and environmental interference.
-
product
12-Channel VME Picosecond Resolution Time-Interval Measurement Module
V660
The V660 is a 12-channel time-to-digital converter used to record the time of occurrence of twelve independent electrical pulse inputs, each independently timestamped and buffered in FIFO memory.
-
product
50MHz USB Pen-Style Frequency/Period Counter
USBcount50
USBcount50 is a new concept in USB Frequency Counter products. PC based frequency counters deliver many user benefits including flexibility, ease of use and economy. They are an invaluable tool during design and debug of digital circuits and can be used to quickly to verify generated frequencies, pulse widths and duty cycles .
-
product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
779351-01
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
product
Pulse Evaluation Systems
*Intuitive, user-friendly handling*Integrated wide-range power supply*Easily programmable output functions*Devices for monitoring standstill, speed, direction, slip, and frequency*Switching relays and transistor outputs, scalable analog output
-
product
DC Vibration Unit Tester
BK2116
As the technology for BLDC motors advances, more advanced testing is also needed. The BK2116 DC Vibration Motor Tester was designed when of several of our clients needed to test the new generation of 3 port DC vibration motors. Using the BK2116, you can test the electrical specifications (RPM, current, drop pulse, and start up voltage) and also vibration level, and noise of motors with either 2 or 3 ports. The BK2116 can concurrently test 2 DUT's and BaKo's Test Shop software makes it very easy to set up and test. And because you use it with a PC or notebook, you can see graphs of the data as you test, and also save it to analyze later, or to analyze the data you gather over time.
-
product
Energy Analyser
DUCA-LCD
Energy Analyser for DIN-rail mounting (4 modules), for Single-Phase/Three-Phase systems with Graphic LCD screen, Co-generation Energy measurement and "Wide Range" Power Supply (24 - 240 Vac/dc); voltage and current waveforms and harmonics measurement and visualization; 2 digital output for pulses or alarms; 2 digital pulse input. Optional RS485 serial line interface (Modbus or ASCII_DUCBUS), Ethernet Interface (Webserver / Modbus-TCP).
-
product
3 1/2 Digital Process Meter
CSN Series
CSN Series 3 1/2 Digital Process Meter is a simple type of economic Panel Meter, and its large LED display with 20.0mm and anti-jamming design, quality, reliable, easy to install.Full range can be specified DC voltage / current, thermal resistance , load cell, potentiometer , Resistance and pulse signals such as the general measurement requirements.
