PXI Serial Interfaces
See Also: Serial Interfaces
-
Product
3U VPX Power Interface Board VITA 62
106PIBC301-0000R
-
3U Convection Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
68 Pin Breakout Interface
VSI-Breakout-68
-
The VSI-Breakout-68 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
PXI Test System
APT-1000
-
18 Slot NI PXI chassis (PXIe-1065)Amfax MDU with E-StopMAC Panel SCOUT Receiver chassis and tableProgrammable DC power supply4 channels- 0-30V 2AFan Vented 29u Instrumentation rackIndustrial PC i7- Windows 7 or 1024 inch touchscreen LED Monitor on armLight TowerCE CertifiedFully wired and testedFull documentation packDelivery and commissioning on site
-
Product
Filtered AC Interface Module
-
AC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of AC power.
-
Product
USB Interface
PK-232/USB
-
The PK-232/USB brickwall filters have tighter bandwidth and steeper skirts for improved noise and QRM rejection. New PK-232 firmware (Ver. 7.2) allows a wider selection of filters than the original PK-232, so the filter can match the mode. The correct DSP filter is automatically selected when you choose an internal mode. In RTTY, Timewave’s proven Twin Peak Filters pluck the mark and space tones from the noise and QRM for great copy. In PACTOR, the filter bandwidth automatically changes when the baud rate shifts in response to the error rate of the link. In Morse (CW), the operator can preset either 100 Hz or 200 Hz bandwidth. The PK-232/USB is compatible with all Windows W2K,XP,Vista/Win7 software terminal programs for the PK-232.
-
Product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
ECU Interfaces
-
ECU Interfaces are devices that connect to an ECU microcontroller directly as a memory emulator or through the debug port interface. The interface is typically through a direct replacement of the microcontroller, memory emulation, or through the debugger port. The method can be driven by what is supported on the microcontroller. ATI offerings support all approaches:
-
Product
Interface Adapter. USB Solution
U2C-11
-
Dimax USB to I2C Bridge device - U2C-11 converts USB transactions to I2C Master transactions. U2C-11 turns your PC running Windows or Linux OS into comprehensive I2C Bus master.
-
Product
A Serial Data Link Monitor for Windows
Listen
-
Listen is a Data Link monitor designed to assist debugging & troubleshooting serial communications links. Listen utilizes standard Windows COM port drivers to tap into RS-232 transmit signals for monitoring bi-directional communications between two devices.
-
Product
30 GHz Differential Probe with 2.92mm Interface
DH30-2.92MM
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
3U CompactPCI Serial 4-slot SSR w/o RTM w/ Ethernet
1CPCIS-304-R200
-
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot right, without rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, without connectors for RTMs (RearTransition Modules), Ethernet full mesh.
-
Product
Digital and Serial I/O
-
VadaTech’s wide range of ATCA Rear Transition Modules (RTMs) and MicroTCA I/O AMCs make it easier to integrate these standards-based building block systems into your network or application.
-
Product
SparkFun USB UART Serial Breakout
CY7C65213
-
The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get the IC quickly up and running.
-
Product
CPCI Or PXI Communication Interface Board
MS 1706
-
*Memory and IO Read Write Cycles*External Interrupts*32 bit Data Bus*30 bit Address Bus*Control Signals for external interface*Four RS232 PORTS with full handshake signals*Four RS232/RS422 PORTS without handshake signals*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Interface Between the Operator and the Sensor
Controller
-
The high-resolution touch screen provides best technical comfort and a virtual keyboard, including Latin, Asian and Cyrillic characters. A real time chart shows the trends and provides quick and clear information about the current process cycle, while the menu and display functions are clearly laid out. The user interface is intuitive and simple to use. Password-protected user administration and a stable, comprehensive data memory for all process values and events ensure the traceability, reliability and safety of the system.
-
Product
Serial to Digital Interface
-
All of ICS's Serial Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
Product
Nano Interface Unit
NIU2A
-
NAI’s NIU2A contains an integrated power supply, two function module slots and an optional ARM® Cortex®-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications. It delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems — in less time, with NO NRE.
-
Product
PCIe Card MX3 Copper Interface
OTP2 module no.183
-
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions.
-
Product
MIL-STD-1553 PMC Interface Module
PMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Shuttle Bus cPCI Intelligent Interface Card
IIB-SB-CPCI
-
The Shuttle Bus cPCI is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, and Multiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification 84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board).In summary, this card provides all features and functions required to meet the above specification, in a cPCI platform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include for LDB_BCT, LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
Product
16-Port Serial Controller
PMC523
Controller
The PMC523 provides a flexible solution for technology insertion by integrating multiple serial I/O channels onto a single board computer (SBC) with a PCI Mezzanine Card (PMC) site. This gives customers affordable protection from obsolescence and a smart evolutionary path to enhanced software ultimately improves performance and increases efficiency.
-
Product
USB Controlled Loudspeaker & Microphone Test Interface
AmpConnect™ ISC
-
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
Product
PXIe, X4, MXI-Express Daisy-Chain Copper Interface, PXI Bus Extension Module
781820-04
Bus Extender
PXIe, x4, MXI-Express Daisy-Chain Copper Interface, PXI Bus Extension ModuleThe PXIe-8374 allows you to create multichassis PXI systems that interface to the same computer. You can use the PXIe-8374 to daisy chain up to eight PXI chassis to the same system computer, which can be a PXI Controller or a PC connected with a Device for PXI Remote Control. You can also extend the PXI system by connecting RAID Arrays, Software Defined Radio Devices, and Software Defined Reconfigurable Radio Devices.
-
Product
3U cPCI Sensor Interface Unit
SIU35
-
NAI's SIU35 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communication, Ethernet switching, and processing. The SIU35 uses up to five NAI field-proven, 3U cPCI boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-To-Mission."
-
Product
Premium Interfaces
-
Ramsey Electronics Premium Interfaces - USB, ethernet, video, and RF filtered power interfaces/rf data connectors
-
Product
RS-232 to RS-422 Optically Isolated Interface Converter
Model 265
-
FEATURES: Eliminates Ground Loops; 19.2 KBPS at 2 Miles;TD and RD Indicators; Use in Pairs as Double Isolated Short Haul Modems; Use in Pairs as Double Isolated Short Haul Modem. Total isolation between RS-232 based systems and RS-422. Unique circuitry allows the RS-422 port to withstand surges exceeding 10 kilovolts.
-
Product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
CAN Interface
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
FPGA Serial Controller Card with Front & Rear I/O
8046
-
The 8046 is a PMC FPGA-based RS422 serial card with front and rear I/O.
-
Product
Easy-to-operate Interface
ANALYSIS 3N
-
ANALYSIS 3N provides an overall view of the whole monitoring points in the network.Each form on the interface symbolizes a DSR data logger. Numbers and names are shown at the topmost of each form, while real-time collected data in the middle, and communication, battery, working and storage status at the bottom. The background of an out-of-limit data turns to be red and keeps flashing.
-
Product
Interface, Kit USB
-
*Connects to a PC for data storage and retrieval from Greenlee digital multimeters*Allows retrieval of stored data and real-time logging and graphing*Retrieve stored data log from DML-Series*Export data to disk for analysis with any spreadsheet
