-
Product
Signal Module, Receiver, QuadraPaddle, 90 Series, 480 Position, Fully Loaded with Twin Female Contacts and Square Posts for Wire Wrap (610 138 200 and 610 138 118)
510150147
Receiver Module
Primary mating module 510151106. (May mate with other ITA modules, as well.)
-
Product
Carbon Pile Load Tester 500 AMP
6034
-
• Carbon pile tester handles all 6/12 volt batteries• Two large 4.5″ analog meters display amps and volts• DC test leads are 2.5′ 4 AWG cable• Unit comes with manual adjust knob• Buzzer sounds after load is engaged for 15 seconds• Imported
-
Product
100GbE Application and Security Load Module
PerfectStorm 100GE 1-Port Load Module
-
Keysight Network Applications and Security
PerfectStorm is a highly modular hardware test platform enabling equipment providers, service providers and enterprises the ability to create real-world, high-stress conditions and user behavior to push new equipment and networks to their limits.
-
Product
DC Electronic Loads
LSG Series
-
*Operating Mode : C.V/C.C/C.R/C.P/C.C +C.V/C.R + C.V/C.P. + C.C.*High Precision, High Resolution (10 A),High Speed Variable Slew Rate (16A/ s).*Sequence Function for High Efficient Load Simulations.*Parallel Connection of Inputs for Higher Capacity. (With 4 Booster Units : Max 9.45kW or 4 Master Units)*External Channel Control/Monitoring via Analog Control Connector.*Program Mode to Create Work Routines for Repetitive Tests.*Multiple-Interface : USB 2.0 Device/Host and GPIB/RS-232C.*Adjustable OPP/OCP/OVP Setting.
-
Product
Arbitrary Load Control For Modulation Distortion
S94570B
-
Extend the modulation distortion application by computing figure of merits such as EVM and ACPR for any desired load with arbitrary load control (ALC). Modulation distortion with ALC integrates the powerful capabilities of the PNA-X with an electromechanical tuner so a non-50 Ω load can be presented to the DUT and changes in device performance or sensitivity to varying load conditions can be accurately measured.
-
Product
Programmable DC Electronic Load
-
Four parameters, highlight VFD display.Resolution of voltage and current: 0.1mV/0.1mA.Four working modes: CV/CC/CR/CP.Three dynamic test function (up to 10KHz): continuous load switching mode, pulse load mode, toggle load switching mode.Ten groups automatic testing data files with each file 10 steps.Intelligent fan cooling, coding switch, built-in buzzer, non-slip feet .Complex current sequence list test mode .Remote sensing function.Battery discharging test mode.All modes turn on default
-
Product
600 Watt DC Electronic Load Mainframe
N3301A
Mainframe
The Keysight N3301A is a half-rack width mainframe with 2-slots that accepts combinations of N330x user-installable load modules (150 W to 600 W) for easy system configuration and future reconfiguration. The N3301A holds up to two N3302A, N3303A, N3304A, and N3307A load modules, or one N3305A and N3306A load modules, allowing up to 600 watts of total maximum power.
-
Product
Load Logger
LL-230
-
AMETEK LoadLoggers* and LoadProfilers are non-invasive digital recording loggers for gathering data on distribution loads and power quality. Whether the data is from a load site or direct from the distribution system, the AMETEK Load Management products are easy to install, operate and analyze.
-
Product
Unclamped Inductive Load Tester
ITC55600C
-
Model ITC55350 is the high current (600A) version of theITC55100 tester. The ITC55350 performs the same testsas the ITC55100 and includes many features that improvetesting accuracy, test results collection, test resultsviewing, and multiple tester networking
-
Product
Electronic Load Mainframe GPIB
3300 Series
-
A 4 Channels 1200W Mainframe which accepts up to four Load Module.
-
Product
Digital Load Cell Simulator
Model EL41
-
Xiamen Elane Electronics Company, Ltd
Detection and debugging of all kinds of weighing instruments - "must have" for any scale service technician - fully RS232 controllable for testing of electronics for scale installation and manufacturing.
-
Product
Static Constant Loading Tester
-
Static Constant Loading Tester is mainly used to determine the resistance to the axial static constant load of plastic manhole. A constant force is steadily loaded on the axial direction of the manhole for the specified time, when the test is finished, observing the sample appearance (deformation, collapse, crack or crazing), determine the deformation in axial direction and calculate the deformation ratio of manhole. The machine is also suitable for ring stiffness test, flattening test, ring softness test of thermoplastic pipes.
-
Product
RC-50 Artificial Phantom Load with Power Factor
480
-
The RC-50 Artificial Phantom Load with Power Factor (Catalog No. 480) has been re-designed to meet the most exacting requirements. It operates from a single phase source and will deliver current at either unity or 50% power factor at all full load ranges.
-
Product
0-600 Amp Variable Carbon Pile Load Tester
6039
-
• Test batteries up to 1200 CCA• Fine threaded shaft for fine adjustment• Temperature compensation chart• Easy to read digital voltmeter & ammeter combine with the versatility of a carbon pile load• Spring loaded to shut-off automatically• Unique curved discs to prevent hot spots• Tests all battery types• Made in USA of US and Global Components
-
Product
VME Load Card
-
WIENER VME load boards are designed to test VME crate power supplies and fan trays by drawing power from the VME backplane and dissipating it as heat. A series of switches on the module front panel allows for easy adjustment of the current draw for each voltage channel.
-
Product
Resistive & Capacitive, Inductive AC Load Bank
RLC
-
Inductive & capacitive load banks are reactive only and must be used in combination with a resistive load bank to provide the desired load profile to test a power system. Reactive loads banks can provide either a leading power factor (Capacitive) or lagging power factor (Inductive).
-
Product
Inductive Load Tester
4602-LV
-
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
Product
Thermal Load Boards
-
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
Product
Digital LOOP/PSC/LOAD Tester
2811 LP
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Displays and sound warning if external voltage present.● Displays mains voltage, scroll trough menus.● Checks wiring integrity (LEDs and display).● Single button operation.● Auto-off/auto-ranging.● Combined prospective short circuit current, PSC and LOOP tester.● Built-in carry case, test leads in separate pouch.● Loop test for L-E and L-N and PSC.● Voltage test L-N and L-E.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for special orders.● 60Hz available on request.
-
Product
Single Point Aluminium Load Cell
EST-2
-
Technopark Automation & Control
The EST-2 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 400x400mm. This load cell is available in capacities from 3kg to 100kg.
-
Product
Spring Loaded Contacts
-
ATE Probes, Pogo pins and Contact Pads. Gold-plated, spring-loaded, capable of thousands of cycles. Probes for Automated Test Equipment (ATE). Various height SMT contact pins. Flat SMT contact pads. Spring loaded contacts consist of a plunger (or head), barrel (or body), and a fully encapsulated fine spring, to provide the spring force required to maintain positive contact. All have a high durability, exceeding 10,000 mating cycles.
-
Product
Medium-power DC Electronic Load (900W~6000W)
FT6400A Series
-
Shenzhen FaithTech Technology Co., Ltd.
The FT6400A series has modular design, with strong adaptability, high reliability and high maintainability. Mainly used in power electronics testing fields such as power batteries, medium and high power DC power supplies, DC generators, etc. The FT6400A electronic load not only provides OCP, OVP, OPP, OTP, RVP but also provides Von and Voff functions and programmable protection functions for the device under test. These features can greatly improve the reliability of the product, and it is a reliable product for engineering test and automatic test system integration.
-
Product
Medium Power Programmable DC Electronic Load(600W~3000W)
FT63200A/E
-
Shenzhen FaithTech Technology Co., Ltd.
The FT63200A/E series of Medium power programmable DC electronic load is designed for high reliability and high power density. It can achieve 2U/3kW, which is twice of the power density of the conventional load. The FT63200A/E series has three voltage ranges of 150V, 600V and 1200V, with a single power range from 750W to 3kW. Its wider working range, extremely fast dynamic frequency, effectively increase the testing capability and application range. The whole series of products have strong overload capacity, instant over power pull up to twice the rated power, can effectively reduce the test cost.
-
Product
Road Load Data / Durability
-
Vehicle Durability Testing and Road Load Data AcquisitionA road load data acquisition system from Dewesoft is a perfect vehicle durability testing solution for real-drive tests or tests on the road simulator test benches. Our advanced DAQ technologies will shorten time to test dramatically and make sure you get the correct measurements right the first time.
-
Product
Personal Workstations for Load Ranges up to 440 lbs.
9200 Series
-
The 9200 Series Vibration Isolation Workstation is a smaller, more compact design providing affordable personal convenience. The 9200 is ideal for applications such as Balances, Optical Microscopes, Cell Injection, Roundness Checkers, and Surface Profilometers.
-
Product
Phantom Load Test Set
-
Is a testing accessory, wisely designed for field testing service. This equipment helps in providing artificial load that is unaltered by the change in power supply.
-
Product
Subsea Shackle Load Cell
SUBS-3.0
-
The Subsea Shackle Load Cell has been designed to measure loads in a subsea environment. DLM’s subsea shackles are suited to fit leading industry Crosby and GN shackles.
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SL
-
*Linear laboratory power supply*Integrated electronic load*Linear regulated DC laboratory power supply*No thyristor pre-regulation, very little ripple*Various interfaces · Built-in electronic load*Protection against short circuit, overload and overtemperature*Constant current and constant voltage*Fast control times approx. 250 µS





























