-
Product
Standard Shackle Load Cell
SS-3.0
-
The DLM Standard Shackle Load Cell is a high strength marine grade cable connected Load Cell. Manufactured from industry leading Crosby or GN Shackles along with a stainless steel load pin.
-
-
Product
Three Phase Phantom Load Test Bench
-
Supreme Instrument Laboratories
Supreme make Phantom Load Test Set is a portable testing accessory designed for field service. It simulates various load conditions usually prevailing in power supply system. The unit offers a practical solution by providing artificial load unaltered by the variation in the power supply mains and adjustable to the complete meter testing requirements.
-
Product
Load Cells
-
is a transducer that is used to create an electrical signal whose magnitude is directly proportional to the force being measured.
-
Product
PXI Load Resistor Module 10 Ohm to 2.56k
40-292-012
Load Resistor Module
A simple solution for applications requiring a programmable load resistor with up to 15W power handling. It is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
Product
Battery Load Tester
BT-100
-
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
Product
Load Pins
-
They are used in many diverse applications including cranes, winches, agricultural equipment (such as tractors), fishing, marine, offshore, subsea, aerospace, process industries, mining, hoisting gear, elevators and floor conveyors, cable laying machinery and many others. The load information provided by the pin can be used for process control, weight/force measurement, overload protection and safety related aspects.
-
Product
Electric Servo Motor Type High Speed, High Load, Large Displacement Vibration Tester
-
This tester is a high-speed, high-acceleration vibration tester equipped with an electric servomotor actuator.
-
Product
Channel Load Generator
802.11p
-
Qosmotec Software Solutions GmbH
When many cars are equipped with 802.11p communication technology, high traffic density will also cause significant load on the radio channel. From normal wireless communication systems it is a known problem, that many users can cause a complete breakdown of the network. Car-to-X communication technology tries to protect itself against those kind of breakdown by a carrier sensing mechanism: Each communication device has to check first, if the radio channel is busy. In that case, it waits for a random delay to avoid packet collision on the radio channel, which causes a loss of both collided packets.
-
Product
110V / 100 Amp Load
BD12-110P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicator will need to be mounted in to a case or control rack for safe use.
-
Product
Pedal Force Load Cells
-
Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.
-
-
Product
48V / 300 Amp Load
BD18-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.
-
Product
Portable Hand Held Load Cell Indicator
MODEL SSI
-
The SSI is a Plug & Play Smart TEDS IEEE 1451.4 compliant portable handheld Load Cell Indicator. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SSI will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SSI can be set up by simple front panel push buttons. The SSI can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, inch pounds, etc. The SSI also has a Units key for automatic conversion of readings for load, torque and pressure. The SSI has an ultra-fast signal-sampling rate of 15,360 samples/second for true peak and/or valley testing capability. Auto-tare allows the meter to be set to zero for any input signal level. The SSI also features a USB port for data logging to a PC. You can also log data to the SSI’s internal memory storing up to 16,000 time and date stamped readings. The SSI also features 2 built-in solid-state alarm relays with LED and audible indicators. The SSI will operate up to 65 hours on a single charge or use the included battery charger for applications where the SSI is mounted permanently.
-
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 5.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,800mm
C_MBT C 5.0 W280 | VP 210160
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 5.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,800 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for large and heavy cars and vans, and with increased loads.
-
Product
Static Load Cells (500 N to 600 kN)
2580 Series
-
The Instron 2580 Series static load cells are high-precision force transducers optimized for use with 5900 and 6800 Series universal testing systems, capable of measuring loads across a wide range (up to ±600 kN) with accuracy to 0.5 % of reading and sensitivity down to 1/1000th of full scale. Temperature-compensated and calibrated on equipment traceable to international standards, they have automatic recognition with an electronic serial number and support electronic calibration, while offering overload protection (up to 150 % without damage, 300 % without mechanical failure). The 2580’s design delivers high stiffness and reliable alignment under load—making it a robust choice for tension, compression, cyclic, and reverse stress testing in materials and components.
-
Product
Medium Capacity Single Point Bending Beam Load Cells
SPL SERIES
-
The SPL Series single point load cell simplifies scale designs, packaging machinery and other industrial weighing equipment. Their single point design eliminates the need for multiple load cells and summing boxes, and thus, simplifies the design and reduces the cost. All SPL Series load cells employ 100% aluminum construction and features a moisture proof sealant which also makes them suitable for damp environments.
-
Product
ResMap or DualMap Manual Load
-
Creative Design Engineering, Inc.
*Type: Table Top*Wafer load: Manual *Wafer size: 2" to 8", 152mm x 152mm*Mini Environment: N/A*Probe Changer: N/A*Aligner: N/A*Size: 12" x 19" x 10"*Range: 1m/ to 10M/*Accuracy: 0.5%*Repeatability: 0.02% *Static Repeatability: 0.1% dynamic
-
Product
Canister Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK provides a wide range of Canister Load Cells designed for high capacity compression applications. These models offer robust construction with a capacity range beginning
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-400B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
SMART Constant Current DC Load Banks
SLB-Series
-
SMART Constant Current DC Load Banks are designed for acceptance testing, discharge testing, battery capacity testing, battery maintenance, engineering examination and other testing for DC power with load. The SMART technology allows a constant current discharge without the need for manual adjustment of current during the discharge test. Our SLB-Series load banks are portable, durable, economic, safe, easy-to-use and come complete with our DataView software, providing the user with a complete data management and analysis program.
-
Product
Single Point Load Cells
-
These have a range of different platform sizes and are suitable for different applications including bench scales, counting scales and other applications in many industries. Click the links below to find out more about each product and to view specific data sheets.
-
Product
Load Tester for D Type Durometers
-
A load tester for checking the spring load characteristics of ASKER hardness testers at the hardness readings of 25, 50, and 75.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Single Point Aluminium Load Cell
EST-5
-
Technopark Automation & Control
The EST-5 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 600 mm. This load cell is available in capacities 50 kg and 100 kg.
-
Product
Load Cells & Mounting Kits
-
Load cells are commonly used to measure weight in an industrial environment. They can be installed on hoppers, reactors, etc., to control their weight capacity, which is often of critical importance for an industrial process.
-
