-
Product
Four-Wheel Drive Single Roller Dynamometer for Cars with Axle Load of 2.4T
MSR 500/3 CAR 4WD | VP 230037
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/3 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/3 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
Product
Modular DC Electronic Load LED Simulator
6310/A
-
Chroma Systems Solutions, Inc.
Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.
-
-
Product
1800~3000W DC Electronic Loads
JT633 series
-
Nanjing Jartul Electronic Co., Ltd
JT633 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT633 series load very suitable for testing power supply when produced in large quantity. Besides, JT633 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT633 series load satisfing most of R&D requirements.
-
Product
Load Cell Power Supply
MODEL PSMR
-
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
Product
Unclamped Inductive Load Tester
ITC75100
-
The ITC75100 is an enhanced unclamped inductive load (UIL) test system that builds on the success of ITC’s industry leading ITC55 series of testers by adding additional test and measurement capability.
-
Product
Micro Power or Micro Coax, Insert, Receiver, SIM, 2 Pos, 2 Slot (not loaded)
510180104
SIM Insert
Not loaded. Micro Power or Micro Coax patchcords need to be purchased separately.
-
Product
Compression Load Cell
EST-20
-
Technopark Automation & Control
The EST-20 is an industry standard Compression Load Cell that can also be used in tension. This load cell can be supplied with load button and cup as well as ball and cup mounting options and is typically used on high capacity silos, hopper scales, batching systems, platform scales, force measurement and tension measurement applications. It is available in capacities from 1 ton to 50 ton.
-
Product
4kW Electronic Load
PT04-48
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 48V and 24V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
Resistive Load Banks
R Series
-
Load banks are devices which contain resistive, inductive and/or capacitive loads, apply the load to an electrical power source and dissipate the power of the electrical source. Portable and stationary resistive load banks incorporate as low as 1 kW load step increments for testing small to large generating sets. The fine control resolution ensures accurate load control and power factor targeting adjustments.
-
Product
Power Supplies And Loads
Power Supply
Power Supplies and Loads power devices under test (DUTs) such as RF power amplifiers and cellular handsets. The power supply takes in AC power and delivers DC voltage with a fixed polarity, either positive or negative, to its load.
-
Product
Electronic DC Load
DL Series
-
Industry’s Easiest-To-Use DC Load – Vitrek’s DL Series Electronic Loads are available in a multiple configurations to meet your unique application requirements. No other electronic DC load on the market today is easier to use. Equipped with a full color LCD touchscreen display, the unit can quickly be set up for your next test. In addition, the DL is equipped with a comprehensive self-test that ensures that all loading and measurement circuitry is functioning properly.
-
Product
Load Tests
-
For the production and quality assurance of electric motors and electric drive systems, the use of flexible and customer-specific testing technology is required. Vogelsang & Benning supplies the same to the needs and the application of the customer.
-
Product
4500~6000W DC Electronic Loads
JT634 Series
-
Nanjing Jartul Electronic Co., Ltd
JT634 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT634 series load very suitable for testing power supply when produced in large quantity. Besides, JT634 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT634 series load satisfing most of R&D requirements. Moreover, JT634 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
Product
Load Cell DIN Rail Signal Amplifier
LCD20
-
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
Product
Signal, Module, Receiver, QuadraPaddle, iCon Series, 160 Position, loaded w/ Twin Female Contacts and Round Posts
510160122
Receiver Module
Fully Loaded with Twin Female Contacts and Round Posts (Adapter Pins) (p/n's 610138200 and 610138117).Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
Product
Signal, Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Square Posts for Wire Wrap with Anti-Rotation (610 138 122)
510151124
ITA Module
NOTE: Part # 510151124 Rev D and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
Product
Portable Three-Phase Current Load
EE-120A-3
-
The Current Source is able to generate three-phase currents, synchronized with the service voltage, with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current is individually adjustable. The values of voltage, current, power, power factor, phase shift, THD and frequency are indicated on the LCD display.
-
Product
GOLDesp Load Planner
-
Provides automated load-planning capability that assists embarkation specialists in the rapid development of cargo load plans
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-600B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Signal / Micro Power/ Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Position, loaded w/twin female contacts
510160112
Receiver Module
This module comes fully loaded with twin female contacts (p/n 610138200), iCon modules mount from the rear of the iCon/i1 receiver allowing installation and removal of pre-wired cable blocks. Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
Product
Network Simulation and Load Testing
-
EXFO offers a complete range of high-performance test solutions, covering the entire converged network from RAN to IMS. By mimicking real-world customer behavior in lab environments, our solutions allow mobile operators and equipment manufacturers to verify their wireless networks before deployment.
-
Product
Load Length Meter
-
Design for finding out the total voltage of neon tubes in a circuit, help to Choose correct rating of neon transformer;- Easy to use just like a neon transformer;- With color LED indicators, clearly shows the test result;- With build-in over voltage protection circuit.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
Product
Load Stability Tester
TruMotion™ Acceleration
-
When transport vehicles accelerate, turn or brake, the resulting low-frequency accelerations can cause unit loads to shift. Due to both safety issues and potential product damage/waste, regulatory bodies are requiring testing that’s closer to reality – assuring safe and stable unit load integrity!
-
Product
Large Telemetry Compressive Load Cell
TC-3.0-LG
-
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.They range from 100t to 300t and manufactured using high grade stainless steel, making these load cells particularly suited to rugged environments and the hire industry. Bespoke size compressive load cells can be designed upon request. Some applications include: tank weighing, hydraulic lifting operations, vessel weighing and certification.
-
Product
Load Cells and Sensors
-
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.
-
Product
Signal Module, ITA, QuadraPaddle, 480 Position, Fully Loaded For Wire Wrap With Anti-Rotation (610 138 122)
510151127
ITA Module
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based Mass InterConnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
Oscilloscope, 350 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2354HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
S-Type Load Cells
-
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
