Well
-
Product
Solar Simulator
Sirius 150A
-
Solar Simulators are used to simulate “real” solar radiation conditions and are widely used for the photovoltaic device research and QA etc.Beam collimation and spot uniformity are important properties along with spectral matching are key operational requirements. The SS150 and SS1000 are suitable for all types of solar cells and well match their optical requirements.
-
Product
LISN Line Impedance Stabilisation Networks / AMN Artificial Mains Network
-
A LISN Line Impedance Stabilization Networks / AMN Artificial Mains Network: *supplies the neccessary mains voltage (AC or DC) and current for the Equipment under Test (EuT).*couples interference voltage generated by the EuT and supplies it to the receiver.*provides well defined RF-impedance to the Equipment under Test (EuT)*keeps away unwanted disturbance coming from mains (filter)*protects the mains from unwanted disturbance voltage generated by the EuT
-
Product
Load Board
cPCI 6U
Load Module
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
Product
Compact PCI Connector Board
cPCI-J2-SCSI
-
Ribbon cable is used between the rear IO and SCSI connector. The lengths are reasonably well matched. The cable is short. The design is intended for lower speed IO - 10 MHz and below. Above 10 Mhz there may be some attenuation.
-
Product
Network Analyzer
DPNA-6G AXIe
-
The AXI DPNA-6G module is the world's first network analyzer in the form factor of the AXIe-1 module, as well as the first Russian device that meets the AXIe-1 standard. In the mode of the network parameters meter, the AXI DPNA-6G module measures the vector values of the network parameters on two ports: transmission coefficients (S12, S21) and reflection (S11, S22). At the same time, all necessary types of calibrations are supported: one- and two-port short-circuit, XX, matched load, transmission normalization. The software supports the import of third party calibration standard parameters. In the measuring receiver mode, the module provides:*generation of a harmonic signal (frequency synthesizer);*spectrum analyzer and power level in a given band;*measuring the frequency of a known signal;*measurement of analog modulation parameters;*phase noise measurement.
-
Product
Rework Station, Dual, Surface Mount, 896 °F
21-10130
-
The 21-10130 is a SMD Rework Dual Station, intelligent rework station which combines rework station with soldering station to become an essential centerpiece of any technician or hobbyist bench. A MCU thermostat provides accurate and consistent working temperature. The dual LCD displays show live working states of both the iron and the hot air hand pieces, as well as provides access to three programmable presets for each unit. Temperature and airflow for the hot air tool can also be controlled from buttons on the hand-piece.
-
Product
PXI FPGA Module for FlexRIO
FPGA Module
PXI FPGA Modules for FlexRIO offer up to 132 singleended I/O lines configurable as 66 differential pairs as well as large onboard FPGAs for signal processing. You can pair the module with FlexRIO adapter modules that offer highperformance analog and digital I/O. Together, the two modules create a reconfigurable instrument.
-
Product
Component Test and Analysis Laboratories
-
The Component Test and Analysis team specializes in electronic and mechanical components such as hybrids, connectors, cables, harnesses, passive or discrete components, and digital or linear devices. The test lab has extensive experience in developing test software to electrically and environmentally characterize virtually any integrated circuit, including analog, digital, mixed signal, converters, FPGA and ASICs, as well as experience in developing actual radiation environments for parts testing. The component analysis team offers the analytical expertise and advanced instrumentation to identify root cause explanation for a wide range of component-level failures, as well as the resources to evaluate for possible quality and reliability issues through non-destructive and destructive techniques. With access to a detailed database, the Component Test and Analysis team offers a 25-year history of test and analysis data — a valuable resource for addressing new customer requirements.
-
Product
High Accuracy Revenue Meter
JEMStar ll IEC
-
AMETEK’s JEMStar II has the highest accuracy in the market, provides many communication options and monitors your power quality to make it the ideal choice for any metering application. An impressive color display makes it easy to view power measurements, phasor displays and meter diagnostics. The JEMStar II is easy to use and configure with our intuitive JEMWARE software and the meter display provides a user menu to show and edit configuration details. The JEMStar II has 1 GB of non-volatile memory to store your metering and power quality data for as long as you want. The meter has a single base model that can be used for simple revenue and billing applications as well as more complex power quality monitoring applications.
-
Product
Thermal FETs
-
Pin-compatible with standard Power MOSFET packages and built-in over temperature protection function for body, lighting and heater applications, as well as powertrain applications and 24V battery system applications.
-
Product
X-Ray Inspection
-
X-ray inspection systems are used wherever defects need to be detected by non-destructive means. The spectrum of use is broad and ranges from quality controls for complex assemblies, to the testing of materials for cracks and air inclusions, to foreign matter inclusions and shape deviations. The trend toward miniaturization, higher packing densities, and the relocation of components to the interior of the assembly require precise X-ray inspections that detect hidden defects quickly and reliably. X-ray systems from Viscom are used for the inspection of series assemblies as well as sampling and prototype controls. They take care of typical inspection tasks in concealed areas such as void controls, THT filling level measurements, and HIP inspections. At the same time, the systems reliably determine defect features such as coplanarity and polarity – at high inspection speeds and in a cost-effective way.
-
Product
Single-Tenant Colocation Cabinets
SmartCabs
-
Benefit from the scale and speed of the cloud while still retaining the control, performance, and security of a dedicated infrastructure. SmartCabs are single-tenant colocation cabinets that come complete with built-in power and network connectivity as well as access to the Digital Exchange, our configurable core network fabric.
-
Product
Microscope Automation
-
Prior Scientific is the world leader in microscope automation, microscope automated precision components and customized sub-assemblies. We offer a wide range of off-the-shelf components such as XY motorized stages, Z focus motors and translation stages, high-resolution microscope stage controllers and robotic slide loaders as well as high-intensity bright field and fluorescence illumination sources.
-
Product
DC-DC Converters (Up To 750 Watt/Module)
A63
-
La Marche Manufacturing Company
The unique design of the LaMarche A63 Series DC-DC Converters will allow you to utilize your 48V, 24V, and/or 12V equipment at a site where 130V batteries are installed. This will save battery, charger, and installation costs as well as reducing maintenance time and optimizing space. The A63 is a compact self contained DC-DC Converter that provides the Modular Power that today's utility substation, process control and telecommunications applications require. The A63 is the building block of these reliable systems using advanced switching technology. Its filtered output provides the clean power required for sensitive loads. The A63 DC output is available in 48V(15 amps) and 24V (30 amps) rated at 750W, or 12V(30 amps) modules rated at 375W.
-
Product
PCIe FPGA Carrier For FMC, Virtex-7
PCI516
-
The PCI516 is based on the Xilinx Virtex-7 690T, which provides 3,600 DSP slices, 52,920 Kb RAM and 690,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR3 memory channels (64-bit wide and 16-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10 G/40 G, SRIO, PCIe) without the need to go through the host.
-
Product
Location Devices
-
Flash Pinger is a small battery powered acoustic transmitter as well as an optical flashing recovery device. Multiple settings allow for selection of flashing, timing, and frequency options for use in a variety of different applications.
-
Product
Dual Channel Variable Filter
4302
-
The Model 4302 Dual Filter is a high performance, low priced, general purpose filter for use in the laboratory as well as in multiple channel data acquisition applications.
-
Product
Input High Temperature Liquid Level Transmitter
HR8005
-
HighReach Measuring & Controlling System Co.,Ltd
HR8005 input high temperature liquid level transmitter is used to measure the water level and water temperature change of high temperature surge well, digital temperature error compensation in full temperature zone, and store the compensation parameters in non-volatile memory.
-
Product
Plug & Play JTAG/SWD Microcontroller Debugger with Built In GDB Server & UART
Black Magic Probe V2.3
-
In most cases Black Magic Debug takes the form of a firmware for the Black Magic Probe hardware, and implements a GNU DeBugger (GDB) server.The Black Magic GDB server features: - Automatic target detection- No need for target specific configuration scripts- All protocol and target specific control is done through GDB monitor commands- No “software in the middle” like OpenOCD required- Easily scriptable thanks to the GDB scripting capabilities- Interface to the host computer is a standard USB CDC ACM device (virtual serial port), which does not require special drivers on Linux or OS X.- Targets ARM Cortex-M and Cortex-A based microcontrollers- Provides full debugging functionality, including: watchpoints, flash memory breakpoints, memory and register examination, flash memory programming, etc.- [Semihosting / Host IO support] as well as [Serial Wire Debug TRACESWO support].- Implements USB DFU class for easy firmware upgrade as updates become available.- Works with Windows, Linux and Mac environments.
-
Product
Satellite & Payload Check-Out Systems
-
Rovsing delivers systems for complete satellite or satellite subsystem testing. Rovsing has developed a modular test system architecture, based on S/W and H/W modules developed by Rovsing for most common space interfaces such as Power, TM/TC, MIL-STD-1553B and SpaceWire. A dedicated test system can then be composed by configuration of the modular architecture, installation of monitoring and control software, as well as test definition and scheduling software as required. Besides reduced development time, this has the advantage that the system to a large extent consists of elements that have been validated on previous missions.
-
Product
8 Channel ADC for PCI
PCI393
-
The PCI393 8-Channel Differential Input ADC for PCI is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs all functionality and user-specific functions can be added for customized operation.
-
Product
TE-Metrology
-
HIGHVOLT Prüftechnik Dresden GmbH
The TE measurement complements the high voltage test and is part of the routine and type testing of numerous electrical devices. It is one of the most important non-destructive methods for detecting faults in electrical installations. The breakdown of an insulating material usually occurs at an internal weak point, which usually already shows a partial discharge activity in advance. For this reason, measuring partial discharges can help prevent costly damage. The TE measurement is thus used for quality testing and diagnosis in the factory as well as during on-site testing of cables, GIS, power transformers and transducers or rotating machinery and their components
-
Product
Cable & Antenna Analyzer - 2 MHz to 4.4 GHz
E7000L
-
The E7000L Cable & Antenna Analyzer provides all necessary measurement functions and performance to accurately diagnose and verify the site’s cable and antenna system and RF connectors, as well as basic fiber-feedline testing. Smaller and lighter than the E7000B, the E7000L is ideal for installation of wireless cell sites.
-
Product
PCI Precision Resistor Card 4-Channel, 2Ω To 26.7kΩ
50-297-132
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Measurement Components
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Innovative developments and modern electronic applications to support everyday life require the use of ever higher frequencies – this applies to specialized areas such as aerospace technology and automotive as well as to the increasing bandwidth requirements in communications technology.
-
Product
Rocket Motor Initiators
-
Our patented Rocket Motor Initiators and Through Bulkhead Initiators are designed to work with single- and multiple-pulse rockets, as well as those platforms that might not currently have MIL-STD-1901A-compliant initiators. Excelitas initiators are designed to work in conjunction with our Ignition Safety Devices and low-energy, low-profile Blue Chip® Detonators to provide a comprehensive and reliable rocket ignition and firing solution.
-
Product
PXIe-8822 2.4 GHz Quad-Core Processor PXI Controller
787881-0118
Embedded Controller
The PXIe8822 is an Intel Core i3based embedded controller for PXI systems. You can use the PXI-8822 to create a compact or portable PC-based platform for industrial control, data acquisition, and test and measurement applications. This PXI Controller includes a 10/100/1000/2500 BASET Gigabit Ethernet port, two HiSpeed USB ports, two USB 3.0 ports, as well as an integrated hard drive, serial port, and other peripheral I/O.
-
Product
Spectrophotometer
Spectro 23RS
-
Spectro 23 RS spectrophotometer is a visible and near ultraviolet spectral range, with high technology of built-in interface RS-232C, to make it possible to communicate with any IBM compatible computer and printer for test documentation as well as to store, record, and print test results. Spectro 23 RS utilizes new generation technology; using a microprocessor for automatic adjusting of 100% T and Zero absorption, Factor and Concentration. Most knobs have been eliminated and replaced by Soft Key, as a result; Spectro 23 RS is really easy to work with.
-
Product
PMC Carrier PXIe x4
-
Looking for a way to plug your PMC mezzanine card into a computing platform with a 4-Lane PXIe slot?Well, the CC_PXIeG1x4_to_PMC is your answer! It is effective, field tested and compliant with all applicable standards.
-
Product
RFP DC Low Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
