Signal Sources
Instrument that provides a stimulus signal (waveform). (www.tek.com)
See Also: Signal, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
-
product
Signal Generators (Signal Sources)
Meet your test requirements with the widest selection of signal generators with the best performance in every class, whether you need a traceable, metrology-grade solution or cost-effective basic signal generation
-
product
Power Dividers
Powers plitters can divide one signal into two or N way equal or non-equal energy, in reverse,they are also used as combiners by combining multiple signal into one. They are mainly used in feed network in antenna array, mixer and balanced amplifier, finish the work of distributing, combining and measuring power, isolating signal sources and measuring swept reflected coefficient etc.
-
product
Microwave Downconverter, 3 GHz to 26.5 or 110 GHz
E5053A
The E5053A microwave downconverter is designed to operate with the E5052A/B signal source analyzer (SSA). When configured with the E5053A microwave downconverter, the E5052A/B SSA offers exceptional phase noise sensitivity up to 26.5 GHz. Additionally, combining a pair of 11970 series harmonic mixers offers the phase noise measurement up to 110 GHz.
-
product
RF Noise Source
NS-3
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
product
Source Phase Control
S93088B
The S93088B allows users to set calibrated, arbitrary phase differences between two signal sources. The sources can be the analyzer’s internal sources or external signal generators routed through the analyzer’s test set. The phase difference can be fixed, or swept between two specified phase values. S93088B also controls the relative power level between the sources using the receiver-leveling feature.
-
product
20GHz 30dBm RF Signal Amplifier
A10200
Model A10200 is an ultra-small footprint, ultra wideband, high power amplifier designed for high frequency, high power, signal amplification. With an ultra high bandwidth of almost 20GHz and up to +28dBm power into 50 ohms, the A10200 is the ideal complimentary amplifier to any signal source that needs an extended power boost for demanding applications.
-
product
SSA-X Signal Source Analyzer, 1 MHz To 8 GHz
E5055A
The Keysight E5055A SSA-X signal source analyzer provides precise and accurate measurements in one box. Comprehensive and versatile, this solution evaluates the phase noise and other relevant parameters for RF signals up to 8 GHz. Flexible measurement settings and a modern user interface improve measurement efficiency, while application support through software expands measurement coverage to meet new requirements.
-
product
Coherent Modulation Transmitter
IQTX
Generating and controlling phase modulated optical signals is easy with the IQTX. The IQTX is referred to as a ‘Golden’ reference optical signal source because of its high repeatability and reliability.Its high bandwidth of 40 GHz ensures high quality optical signal generation, making it the ideal optical signal source for coherent communications applications.
-
product
Signal Combiner
Becker Nachrichtentechnik GmbH
In large scale RF signal distribution systems such as broadcast signal distributions, several signals of radio bands have to be transmitted over longer cable distances. Due to the different frequency ranges, the signals can be transmitted via one common coaxial cable. This saves costs for the coaxial cables and their installation. With help of signal combiners, multiple signal sources can be combined broadband or frequency selective to a sum signal with low loss in level.
-
product
Broadband Threshold Detectors
KRYTAR's All NEW Broadband Threshold Detectors are hermetically sealed for high reliability and are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
product
Thermal Inducing System
Wewon Environmental Chambers Co, Ltd.
Design and development is the stage with the most type of thermal inducing system, It mainly includes oscilloscope, signal source, spectrum analyzer (signal analyzer), vector network analyzer and other general thermal management solutions, As well as channel simulator, terminal simulator, base station simulator and other dedicated thermal inducing system.https://www.wewontech.com/thermal-inducing-system/
-
product
Signal Splitters
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik GmbH offers a comprehensive portfolio of active multicouplers and bi-directional signal splitters for duplicating RF signals from common sources. The multi-couplers are designed in 50 ohm technology and are available as a 19 ", 1 U devices as well as slot-in modules for our 'Modular RF Systems' platform. With help of the slot-in modules, larger scale distribution structures can be realized in a space-saving and cost-effective manner. Some devices are available in variants for AC or DC power supply and provide service-friendly remote monitoring capabilities. For use in the production of infotainment components special multi-couplers with integrated HF and DC test functions are available. The multi couplers are used in applications like radio monitoring and direction finding, in product development, validation, manufacturing, quality assurance and in the field of research.
-
product
RF Signal Amplifiers
The A10200 RF amplifier was designed to extend the power range of the Tabor arbitrary waveform generators and RF signal generators, yet it is compatible with many signal sources instruments.
-
product
Matrix Switchers
Route a wide range of video, audio, and high resolution signals from multiple sources to multiple destinations.
-
product
Variable Gain High Speed Linear Amplifier
F30PV
The F30PV is a very fast general purpose linear amplifier having a variable amplification of 0-10 times and capable of bipolar voltage output of ±35V. Any functiongenerator or arbitrary waveform generatoror any othe signal source can be used as an input device. The amplifier's output is linear from DC up to ca 10 megahertz range. It can be used in a wide range of high speed applications.
-
product
1231a Very High Frequency Distribution
Precise Time and Frequency, Inc.
The ptf 1230A(1U)/1231A(2U) GPS L-Band RF Distribution amplifiers provide high performance GPS signal references for laboratory or systems use. In most applications the low noise and signal gain capability of the units will provide userswith a robust GPS signal source for lab or system requirements.The ptf 1230A/1231A uses individually buffered output stages and insures maximum isolation between the individual outputs. The ptf 1231A offers 12 outputs. Options are available for a 2U/3.5” version (ptf 1230A) with 24 outputs.Isolation from output to output is >-40 dB. The input also offers DCV for biasing an active antenna.
-
product
Process Calibrators
Handheld calibrator-multimeter of industrial process signals including voltage, current, resistance and temperature. External signals up to 200 V or 100 mA can be measured simultaneously with signal sourcing.
-
product
25 Channel Potentiostat/Galvinostat
ArrayPGstat
For any selected cutoff voltage or current, early finishers are held at open circuit until all cells complete the charge or discharge period. All cells are switched at identical state-of-charge.- Multichannel potentiostat/galvanostat- Compliance voltage ±15 V- Voltage control ±10 V- Waveform signal sources (4 maximum)- ±100mA/channel (40 channels maximum)- 8 kHz bandwidth- Maximum scan rate 100 V/sec- Battery charge-discharge cycling: Time and/or voltage switching parameters.
-
product
Precision Capacitance Meter
TH2638B
Changzhou Tonghui Electronic Co., Ltd.
TH2638 series is a new precision capacitance meter with higher test frequency. With small size and portable appearance, it is convenient for use on the shelves. With basic accuracy of ±0.07%, loss accuracy of 0.0005, test frequency up to 1MHz, 4.3-inch LCD screen, selectable Chinese-English operation interface, TH2638 series is easy to operate and provide fast and reliable test for ceramic capacitor production. Also, it can test all kinds of capacitors from low value to high value. The results of testing one capacitor for several times are quite stable and accurate, even for lower value capacitors. The tester is compatible with SCPI command set, and configured with manipulator and scanner interface, the scanner interface can scan the open/short/ load error calibration in each channel, 256 channels at most. In low frequency, there is signal level compensation function. When the impedance is very small, the internal resistance in signal source and test cable will cause the voltage on terminal of DUT lower than the set range, then this function will adjust the level to the set range.
-
product
256 GSa/s Arbitrary Waveform Generator
M8199B
The M8199B arbitrary waveform generator (AWG) provides R&D engineers with a high-performance arbitrary signal source, enabling design development at 160 GBaud and above. The M8199B AWG enables up to 8 synchronized channels at 256 GSa/s with nominal analog bandwidth exceeding 80 GHz. With integrated frequency and phase response calibration for clean output signals, the M8199B simplifies your test setup.
-
product
Unipolar High Voltage Linear Amplifier
P150
The P150 is a general purpose linear amplifier having a fixed amplification of 20 times and capable of unipolar high voltage output of +150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to +10 V can be used as an input device. The amplification can be set to x15 (or other value) on request.
-
product
Analog Output PXI Card
GX1642
The GX1642 is a 3U PXI digital to analog output board is designed specifically for applications where multiple analog outputs are required. The GX1642 offers precision signal sourcing performance and quality at an economical price.
-
product
Signal Amplifier
A10150
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
-
product
Multi-Channel Vector Signal Generators
875
Berkeley Nucleonics Corporation
The Model 875 is an ultra-fast-switching vector-modulated signal source covering a continuous frequency range from 10 MHz to 40 GHz. The Model 875 offers switching speeds as fast as to 200ns, enables ultrafast CW frequency sweeps, chirping, intra-pulse modulation and pulse shaping, all with very low phase noise. A high-performance internal I/Q modulator enables customized modulation waveforms and supports dedicated modulation schemes such as avionics modulations. This newly engineered design couples extremely deep memory and wideband capabilities - making complex modulation affordable and easy to program.
-
product
Speaker Component Checker
Cab Driver
Whirlwind Music Distributors, Inc.
The CAB DRIVER is a test device for checking the operation of the speaker components within enclosures. A pink noise signal source is sent through pushbutton selectors to an assortment of speaker connectors, including Speakon NL8 and NL4, 1/4" TS and banana jacks. Speaker/ Polarity/ Impedance/ Pink Noise Generator
-
product
Saluki LSG022 Analog Signal Generator (Modular)
Saluki LSG022 analog signal generator offers 100kHz to 22GHz frequency coverage with 10ms frequency switching speed. It can be used independently or combined with the chassis to form a test system.Saluki LSG series signal source is the cost-effective choice when you need to balance budget and performance. It provides the signals you will need for radar performance evaluation, high-performance receiver test and components parameter test etc..
-
product
Tone Generator
A15TG
The Shure A15TG Tone Generator is a battery-powered 700 Hz signal source used to troubleshoot audio systems by checking microphone lines for correct patching and detecting unusual noise that is present. The output level of the A15TG is approximately 42 dBV.
-
product
Rubidium Frequency Standard
RFS VXI
*RFS VXI is designed to work as part of information measuring systems based on the VXI bus as a rubidium frequency standard.*RFS VXI is intended for use as a highly stable laboratory signal source for checking generator devices, time-frequency measuring equipment and other equipment, synchronizing navigation systems.*The RFS VXI contains two independent rubidium reference oscillators: main and standby.*RFS VXI is a VXI standard, register based device and measures C-1.*RFS VXI implements the "Self-control" mode, which checks the output frequencies of the rubidium standard.
-
product
NI-9231, 8-Channel, 51.2 kS/s/channel, -5 V to 5 V, C Series Sound and Vibration Input Module
783610-01
8-Channel, 51.2 kS/s/channel, -5 V to 5 V, C Series Sound and Vibration Input Module - The NI-9231 is a high-density sound and vibration module that can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. It can perform the high dynamic range measurements necessary for modern measurement microphones and accelerometers and features simultaneous sampling. The NI-9231 incorporates both a TEDS input path and 2 mA of IEPE signal excitation source that can be turned on and off, removing the need for external sensor power and reducing the complexity of the data acquisition system.
