Signal Sources
Instrument that provides a stimulus signal (waveform). (www.tek.com)
See Also: Signal, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
Matrix Switchers
-
Route a wide range of video, audio, and high resolution signals from multiple sources to multiple destinations.
-
Product
2GHz programmable frequency dividerValon
3010a
-
The Valon 3010a accepts a wide range of input frequencies and provides three independent, user-selectable, divided outputs. The 3010a is useful for extending the low-frequency range of any signal source down to 5MHz as a 50Ω output or down to 0Hz as a TTL output.
-
Product
Modulated Wideband Driver Amplifier
TBMDA2
-
The TBMDA2 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its 1dB compression point of +27dBm, it can boost the output power of a tracking generator up to 500mW.
-
Product
Speaker Component Checker
Cab Driver
-
Whirlwind Music Distributors, Inc.
The CAB DRIVER is a test device for checking the operation of the speaker components within enclosures. A pink noise signal source is sent through pushbutton selectors to an assortment of speaker connectors, including Speakon NL8 and NL4, 1/4" TS and banana jacks. Speaker/ Polarity/ Impedance/ Pink Noise Generator
-
Product
Signal Analysis
Synchronous Accumulation (Order Analysis)
-
Order analysis is one of the most convenient and efficient methods for diagnostics and balancing of rotating mechanisms and transmission gears. With an RPM sensor and a vibration sensor, it is possible to study the time characteristics of gear vibration signals. It is a well-known fact that a signal from a vibration sensor is affected by signals from other sources. To tune out from the disturbing signals, the synchronous signal accumulation method is used. For each shaft rotation, the RPM sensor provides a rotation mark. This signal serves as a triggering strobe for the vibration sensor signal sweeping. The obtained signal sweeps are combined. All the sources of the signals related to the shaft frequency (frequency of rotation) are accumulated and increased in the accumulator linearly proportionally to the N number of rotations. All other signals that are not correlated with the shaft frequency are accumulated proportionally to N1/2 and in case of a greater number of averagings, the useful signal exceeds the interference level.
-
Product
Measurement Hardware
-
Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.
-
Product
Keysight Dual 1x2 SPDT Terminated Microwave Switch Module for 34980A
34946A
Microwave Switch Module
The Keysight 34946A microwave switch for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching for test signals from DC to 26.5 GHz. These switches provide excellent insertion loss, isolation, and VSWR specification. The microwave switches are configured as two independent 1x2 (SPDT) terminated switches on a single module. For general-purpose microwave switching applications, the module can be used to switch separate signal sources for a multi-band receiver/transmitter testing application.
-
Product
High Voltage, High Current Linear Amplifier
P200
-
The P200 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
Product
Comb Generator
CG 50/500
-
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN.reference signal source Noise Generators Signal Generators
-
Product
Source Phase Control
S95088B
-
The S95088B allows users to set calibrated, arbitrary phase differences between two signal sources on the M980xA PXI VNAs.
-
Product
PXIe Vector Network Analyzer RF Distributor
M9340A
Vector Network Analyzer
The M9340A PXIe vector network analyzer RF distributor is used in the M9485A PXIe multiport vector network analyzer. The module distributes the source and local signals from the source modules to the receivers.
-
Product
Thermal Inducing System
-
Wewon Environmental Chambers Co, Ltd.
Design and development is the stage with the most type of thermal inducing system, It mainly includes oscilloscope, signal source, spectrum analyzer (signal analyzer), vector network analyzer and other general thermal management solutions, As well as channel simulator, terminal simulator, base station simulator and other dedicated thermal inducing system.https://www.wewontech.com/thermal-inducing-system/
-
Product
Source Phase Control
S93088B
-
The S93088B allows users to set calibrated, arbitrary phase differences between two signal sources. The sources can be the analyzer’s internal sources or external signal generators routed through the analyzer’s test set. The phase difference can be fixed, or swept between two specified phase values. S93088B also controls the relative power level between the sources using the receiver-leveling feature.
-
Product
All-In-One Infotainment RF Signal Source
AST-1000
-
The software-defined AST-1000 is powered by Averna’s RF and test expertise, enabling you to generate all common radio signals (e.g., AM/FM, HD Radio and Sirius/XM), digital video signals (e.g., ATSC, CMMB and DVB-T2), and simulate all common GNSS signals (e.g., BeiDou, Galileo and GPS).
-
Product
20GHz 30dBm RF Signal Amplifier
A10200
-
Model A10200 is an ultra-small footprint, ultra wideband, high power amplifier designed for high frequency, high power, signal amplification. With an ultra high bandwidth of almost 20GHz and up to +28dBm power into 50 ohms, the A10200 is the ideal complimentary amplifier to any signal source that needs an extended power boost for demanding applications.
-
Product
2x16 Channel Multiplexer
FXA-103 MUX 16×2
Multiplexer Module
The FXA-103 is a two times sixteen channel multiplexer which allows to route analog or digital input signals from multiple sources to one measurement device. To simplify control the corresponding relays of both multiplexers are switched together and each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
Product
SSA Signal Source Analyzer, 10 MHz to 7 GHz, 26.5 GHz, or 110 GHz
E5052B
Signal Analyzer
RF Input frequency range: 10 MHz to 110 GHz Analysis offset frequency range: 1 Hz to 100 MHz Phase noise measurement with ultra low noise floor and a cross-correlation method Frequency transient capture range: up to 80 MHz in narrow band, up to 4.8 GHz in wide band
-
Product
Polarization Maintaining Fiber Components
-
OZ Optics offers a broad range of polarization maintaining components, patchcords, and connectors designed to resolve polarization problems, which are becoming increasingly important in today's higher speed and more complex mesh optical networks. By maintaining the polarization of the signal at its source, our polarization maintaining components minimize polarization mode dispersion and eliminate the effect of polarization dependent loss thereby increasing the quality of the signal that is transmitted throughout the network.
-
Product
Telecom Test Systems
4301 Series
-
The 4301 is designed to work with a standard arbitrary wave form generator or signal source that can be triggered. The system can be ordered with an optional Fluke 281 arbitrary waveform generator, which comes pre-programmed and integrated into the 4301 system. When equipped with the Fluke 281 option, the 4301 provides a complete solution for GR-1089 Section 10/ATIS-0600315.2007 testing.
-
Product
Rubidium Frequency Standard
RFS VXI
-
*RFS VXI is designed to work as part of information measuring systems based on the VXI bus as a rubidium frequency standard.*RFS VXI is intended for use as a highly stable laboratory signal source for checking generator devices, time-frequency measuring equipment and other equipment, synchronizing navigation systems.*The RFS VXI contains two independent rubidium reference oscillators: main and standby.*RFS VXI is a VXI standard, register based device and measures C-1.*RFS VXI implements the "Self-control" mode, which checks the output frequencies of the rubidium standard.
-
Product
Encoder
SFT3211HS
-
Hangzhou Softel Optic Co., Ltd.
SFT3211HS H.264/HEVC HD Encoder is the new broadcasting audio & video encoding device with powerful functionality. It is equipped with multiple video input interfaces (HDMI, SDI, YPbPr and CVBS) and audio input interfaces (AES, RCA and XLR) to make it possible to compatible with different signal sources.
-
Product
Register
Trend Viewer
-
A trend is a diagram facilitating analysis of long records of measured sensor values (for hours, days, months, years). Based on the sampling frequency, an n number of counts per second are performed, and their yearly number equals to 31,556,926*n. If the user needs to evaluate short-term moments of the source signal, then there is no difficulty. It is much more difficult, when it is necessary to evaluate the parameters for the entire year or several years, and no monitor and no person would handle it. And this is the case when trend building could help.
-
Product
Remote Data Acquisition
-
Sometimes your sensors or the piece of equipment you are trying to control is not in a convenient place to have a PC close by. The sensors may be widely distributed through out your plant and it just wouldn’t be cost effective to run all your wiring to where the PC is. In addition, low level signals are more accurately acquired when digitized close to the signal source. In all these cases our REMOTE ACCES line of products will help. The REMOTE ACCES pods are intelligent, sensor to computer interfaces. Each pod can be used as an autonomous data logger to acquire data for later download. Or as many as 31 pods may be connected on a single two wire multidrop RS-485 network allowing a cable distance of up to 4000 ft. You can also go wireless and extend your range by adding RS-485 wireless transceivers to your serial port. Each unit comes in a rugged NEMA 4 enclosure and can withstand harsh industrial and marine environments.
-
Product
Frequency Converter
FC5-29M
-
Frequency converter FC5-29M is a measurement instrument which is designed for spectrum conversion of 75 - 170 GHz to 1 MHz ÷ 2,6 GHz range and automatic frequency measurement of sinusoidal signals. When combined with the 1 MHz - 3,0 GHz spectrum analyzer, FC5-29M can be used for examination of the continuous and periodically repeating pulse signals.The instrument is meant to be used for measurement of various signal sources, radio-transmitting instruments, synthesizers, frequency converters, measurement generators and also for adjustment and verification of various radio-transmitting or communication instruments in laboratory and workshop conditions.
-
Product
PXI Signal Generators (Signal Sources)
Vector Signal Generator
Accelerate test throughput with fast, high-quality measurements optimized for RF or microwave design validation & manufacturing testIncrease test configuration flexibility with a PXI platform and license key upgradesReduce development time with easy integration of drivers and programming examples into test environments
-
Product
Field Strength Meters
-
The FSM series of field strength meters will measure the strength of a RF signal appearing at its input from +20 dBm to -110 dBm for wide bandwidth models and +10 dBm to -120 dBm for narrow bandwidth models. The RF strength will be displayed on an LCD display to an accuracy of ±3 dB over the entire 130 dB dynamic range. A matching field signal generator is also available to act as a signal source for propagation studies.
-
Product
Planar Doped Barrier Detectors
-
KRYTAR Planar Doped Barrier Detectors are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
Product
12/24/40 GHz Microwave Analog Signal Generator
CA9600 Series
-
CA9600 Series Microwave Analog Signal Generator is a cost-effective product that focuses on the targeted market. Design Concept – follow simplicity and highlight focuses. By getting rid of the useless functions on the traditional signal source products which the targeted market is barely using and enhancing the core index of signal source that includes spectral purity, output power, and portability, CA9600 promise you an excellent performance, compact, portable, economical, convenient, and reliable testing assistant.
-
Product
6GHz Dual Frequency Synthesizer moduleValon
5009
-
The Valon 5009 Dual Frequency Synthesizer module is our latest offering in high frequency synthesizer sources. These frequency synthesizers are perfect in applications that require a spectrally pure and highly stable signal source or timing clock. Our synthesizers have replaced laboratory generators costing many times more in a number of applications. Each module actually contains two independent sources locked to the same internal or external frequency reference or standard. Having two phase coherent sources in the same convenient package opens up a wide variety of test applications and solutions
-
Product
Single Channel High Voltage Linear Amplifier
A800
-
The A800 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of ±400V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±4 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
