Interoperability Testing
assures functionality between two distinct elements.
See Also: Interoperability Test
-
product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
product
Functional Test
cUTS
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
-
product
VR/AR/MR Calibration Platform
AR, VR and MR device calibration is critical for product performance. Leverage Averna’s standardized alignment platform to efficiently calibrate cameras and Inertial Measurement Unit (IMU) modules with supreme accuracy. Easily customize or upgrade the base platform into the automated quality solution to best fit your manufacturing requirements.
-
product
Test Platforms
Leverage 20+ Years of Test Industry Experience with Built-In IP for Maximum Reuse
-
product
Conformance Test System
TS8980
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
product
Battery Management (BMS) Environmental Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
product
SoC Test Systems
SoC (System on Chip) devices integrate multiple different functions into a single chip. Our SoC test systems can test all the integrated circuits in SoC devices, including logic, analog, RF, DC and imagers by flexible configuration of the cards/modules used in the test system.
-
product
Military Communications Test
Astronics testers for military radios and wireless communications systems help you keep your most critical communications up and running smoothly. Write test program sets once and deploy them instantaneously everywhere – whether your test set is in the factory, at the depot, or in operation.
-
product
Test System
UltraFLEX
The UltraFLEX test system delivers the power and precision you need for complex SoC devices built for mobile applications, networking, storage or high-end processing. Choose UltraFLEX when your device mix and throughput goals demand the highest speed, precision, coverage and site count.
-
product
PCB Test System
Circuit Wizard - CW409
Qmax Test Technologies Pvt. Ltd.
CW 409 –Circuit Wizard PCB Test System has all the features of QT9627 such as Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test.Maximum Digital Test Speed 10MHz in the QT9627 .It can be connected to any PC/AT or Laptop with Windows 10 operating system through USB Plug and play interface. It operates on user friendly Qmax Test Director software platform with different modes like Test Station for operator level use Test Sequencer mode for Programmer level use and Interactive Workstation mode for quick working.
-
product
NI Semiconductor Test Systems
The STS delivers the openness and flexibility of the NI PXI platform to the semiconductor production environment. For easy integration into the production test cell, the STS comes with features such as handler/prober integration, spring probe device under test interfacing, STDF data reporting, and system calibration.
-
-
product
ESD Test System
58154 Series
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
product
ARINC 818 Tester
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
product
Batterie Inspektor
By combining the most diverse hardware and software modules, Batterie Inspektor™ delivers innovative, automated, and digitalized battery testing at every stage of manufacturing. With this flexible test platform, all modules can be adapted to their respective quality requirements. Manufacturing is simplified through a scalable and standardized framework for both new projects and upgrades.
-
product
Design for Testability (DFT Test)
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
product
EV Power Components End of Line Test Platform
Test and Validate all EV Power Electronics with One Flexible and Scalable Solution
-
product
VLSI Test Systems
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
product
Image Sensor Testing
IP750Ex-HD Family
The IP750EX-HD has been the test platform that has enabled the industry to manufacture high quality CCD and CMOS image sensors, and it is the most economical platform to meet the needs of newer technologies such as Time of Flight (ToF) sensors. When you use a smartphone, high performance digital still camera, or in-home security and surveillance system, these applications have image sensors most likely tested by Teradyne’s IP750ExHD.
-
product
NI Real-Time Test Cell Reference System
780590-35
VeriStand Full Development License with NI Standard Service , Include 1 Year SSP
-
product
Seno-Con Test System
PANTHER 2K QST
Qmax Test Technologies Pvt. Ltd.
Panther 2K-QST is a versatile ultra fast Seno-Con test system designed to test high volume ,low to high pin count consumer semiconductor IC’s for its assembly line wire bonding faults. Its innovative test technology helps learn from known good device and test against target device drastically reduces time required to develop Test programs.The operating software is designed in such a way that it is fully user friendly with GUI programming.
-
product
Flight Control System Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
product
HV Test System for Patient Monitors
HV test enclosure for testing medical products (patient monitors). Insulated test booth with large space for DUT.3 different test nests for adapting different devices.Displays from patient monitors are checked. For this, insulation tests and leakage current measurements must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
product
OTP-Based Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
product
Off-Line Seat Operation Base Test Platform
6TL23
The 6TL23 is a bare rack for creating Off-Line, modular, flexible, and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation since there’s space for the operator’s legs under the fixture receiver.
-
product
Digital Test Instruments
Conduct pattern-based digital tests incorporating the latest parallel, digital, serial, and bus protocols with the PXIe-6943 digital test instrument.
-
product
Benchtop Communication Test System
ATS3000A
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
product
Explosive Test Site Range Instrumentation
Firesets, CDU’s EDU’s, Delay generators, firing panels, and custom instruments. Fiber-optic and computer-control options.
-
product
3-Axis Non-Robotic Automated Testing System
AT3
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
