Switching Matrix
expand availability of instrumentation I/O fulfilling test node array connections.
See Also: Switching, High Voltage Switching, Switching Matrices, Multiplexers, General Purpose Switch, Mass Interconnect
-
Product
Solid State PIN Diode Transfer Switch, 100 MHz to 18 GHz
P9400C
-
The Keysight P9400C solid state PIN diode transfer switch offers outstanding performance in terms of port-to-port isolation, switching speed and low insertion loss over a broad operating frequency range of 100 MHz to 18 GHz. The P9400C is particularly well suited for ultra-fast RF and microwave switching applications in instrumentation, communications, radar, switch matrices and various other test systems where high isolation, speed and lifetime of a switch is critical.
-
Product
PXI 8-Slot BRIC Matrix, 203x8 2A 2-Pole (7 Sub-cards)
40-565B-102-203X8
Matrix Switch Module
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
Product
USB Coaxial Switch, DC to 26.5 GHz Dual SP6T
U1816C
Coaxial Switch
The Keysight U1816C is a switch matrix that consists of two single-pole-six-throw (SP6T) switches. It allows switching of multiple signal paths without physically changing the connections. This allows multiple tests to be performed with the same setup, eliminating the need for frequent connects and disconnects. An entire testing process can be automated, increasing the throughput in high-volume production environments.
-
Product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
Relay Matrix Module
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI 16x2 RF Matrix 300MHz 50 SMB With Loop-Thru
40-728-001-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
SWB-2810, 4x43, 1 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-10
Reed Relay
4x43, 1 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI/PXIe Switched Guard Matrix, 16x4
40-590-101
Matrix Switch Module
The 40-590-101 (PXI) and 42-590-101 (PXIe) are modules that provide a switched guard 16x4 matrix solution with up to 1012 Ω channel to channel and channel-to-ground isolation.
-
Product
PXI BRIC8 FIBO Matrix Dual 217x4 2pin brkout
40-592A-117
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
Product
Single Board Source/Meter/Switch
SMSU
-
SMSU Series SourceMeterSwitch Unit (SMSU), introduced by SW Link Ltd, is single-channel voltage/current sourcing, 4X6 switch matrix and measurement instruments. Each Series 100 SMSU instrument tightly integrates highly accurate stable DC power source and a true instrument-grade programmable gain amplifier and 18bits ADC on a 100x100mm PCBs. It can output up to 20V, sub-uA to 1A current to device under test (DUT)
-
Product
PXI 8-Slot BRIC Matrix, 29x8 2A 2-Pole (1 Sub-card)
40-565B-102-29X8
Matrix Switch Module
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI BRIC8 FIBO Matrix Dual 80x4 3pin brkout
40-592A-104
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
High-Speed Digital Switch Matrix & Optical Power Management System
VERTA
-
Avionics Interface Technologies
Switching & Optical Power Management system supporting Fibre Channel & Ethernet interconnect and power management applications.
-
Product
PXI 16x4 RF Matrix 300MHz 50 SMB With Loop-Thru
40-727-001-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
4x4 HDMI Matrix Switch with RS232 and IP Control
HSM-I-04-04
-
4x4 HDMI matrix switch with RS232 and IP control. Supports HDCP, deep color, multi-channel digital audio (up to 7.1 channels), and may be used with any combination of DVI (PC) or HDMI (HDTV) sources and displays.
-
Product
PXI BRIC8 FIBO Matrix Dual 20x4 3pin brkout
40-592A-101
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
Product
Computer Controlled, Solid-State RF Switch Matrices
-
PMI offers a full product line of RF Switch Matrices that operate over the 20MHz to 40GHz frequency range. Three standard models are offered that cover this frequency range, namely 20MHz to 3.0GHz, 2.0GHz to 18.0GHz, and 18.0GHz to 40.0GHz. Any of the three models can be supplied as either a 4 X 4, 8 X 8, 16 X 16, or 32 X 32 non-blocking matrix.
-
Product
USB Type-C Interconnects Compliance Test Software
S94USBCB
-
Use the S94USBCB software to test, debug and characterize your USB Type-C cable and connector designs. The PathWave TAP based test sequencer automates the network analyzer (VNA) for each test and generates a comprehensive HTML report. When run with L8990M switch matrix, it enables 20-ports fully automated test without port re-connection.
-
Product
PXI 4-Slot BRIC Matrix, 116x8 2A 2-Pole (4 Sub-cards)
40-565B-002-116X8
Matrix Switch Module
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781420-11
Reed Relay
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
TB-2636, Screw Terminal, 4x32, 2-Wire PXI Module Matrix Terminal Block
196762-01
Terminal Block
The TB-2636 provides the necessary routing to configure the PXI-2529 PXI Matrix Switch Module as a 2-wire 4×32 matrix. You can directly connect the TB-2636 to the front panel I/O connectors of the PXI-2529. The TB-2636 includes screw terminals that provide access to the rows and columns of the matrix.
-
Product
High Power, Low PIM Switch Unit
LPSU series
-
LPSU series high power, low PIM switch units combine 65 low PIM ports or 14 low PIM ports. These switch matrices are designed in testing situations that require multi-band PIM sources, components or antennas. Combinations of multi-band PIMtesting are now easily possible, improving workflow significantly. LPSUs can be integrated in existing production control systems. Frequency range 698-2700 MHz.
-
Product
NI TB-2643B Terminal Block for NI 2532B as 1-Wire Dual 4x64 Matrix or 2-Wire 4×64 Matrix topology With Column Protection Resistors
782385-08
Terminal Block
The TB-2643B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x64 or 1-wire dual 4x64 matrix. You can directly connect the TB-2643B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2643B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Broadband
-
Quintech Electronics and Communications Inc.
Software or an online tool used to customize the settings and configurations of a physical broadband RF (Radio Frequency) matrix switch or a related signal management system.
-
Product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix Topology Without Column Protection Resistors
782385-11
Terminal Block
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
ASA240
-
The ASA240 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software, with the ASA240 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.The built switching matrix (40 x 2) is easily configured from the software and maybe used with adaptors (such as DIP or SO) to speed up testing of boards, or maybe connected to a ‘bed-of-nails’ to facilitate rapid testing of boards in production.With the ASA240 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
Product
Configurable High-Density Switch Matrix PXI Card
GX6384
Multiplexer Module
The GX6384 3U PXI multiplexer switch card provides users with the ability to switch and interface tester resources to multiple UUT connections. The card is available in three different configurations, supporting 32 x 2, 32 x 4, and 32 x6 switch configurations.
-
Product
PXI 16x2 RF Matrix 300MHz 50 Multiway Connector With Loop-Thru
40-728-002-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI-2536, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-36
Matrix Switch Module
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2536 is a high-density 8x68 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring FET relays, the PXI‑2536 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
Low-Density PXI Switch Matrix Modules
-
Our low-density PXI switch matrix modules are a cost-effective solution for applications that require relatively small matrices in the PXI format. These low-density switch matrices can be expanded by connecting together multiple modules, however, we recommend that users look at the higher density switch matrix modules that involve less user configuration. Reed relay versions use high quality sputtered ruthenium relays that exhibit excellent contact performance under low and medium level switching conditions. For general purpose applications that also require higher power handling, the range of electro-mechanical relays provides an ideal solution.
-
Product
Signal Conditioning and RF Distribution
-
CAES provides high performance signal conditioning and RF distribution solutions such as switch matrices for the EW, missile, radar, communications and space markets. Our custom designs offer high speed switching, low insertion loss, low harmonic level and excellent isolation.
