Switching Matrix
expand availability of instrumentation I/O fulfilling test node array connections.
See Also: Switching, High Voltage Switching, Switching Matrices, Multiplexers, General Purpose Switch, Mass Interconnect
-
Product
Switching Matrix
MUX
-
The Analog Signal Switch Unit serves as a 6-bus interconnect for 128 pins each to the Analog Measurement Unit (AMU05) for the In-Circuit test.
-
Product
PXI 8-Slot BRIC Matrix, 203x8 2A 2-Pole (7 Sub-cards)
40-565B-102-203X8
Matrix Switch Module
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI BRIC8 FIBO Matrix Dual 31x4 2pin brkout
40-592A-111
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
Product
PXI 8-Slot BRIC Matrix, 232x8 2A 2-Pole (8 Sub-cards)
40-565B-102-232X8
Matrix Switch Module
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
Product
High-Speed Digital Switch Matrix & Optical Power Management System
VERTA
-
Avionics Interface Technologies
Switching & Optical Power Management system supporting Fibre Channel & Ethernet interconnect and power management applications.
-
Product
4x4 HDMI Matrix Switch with RS232 and IP Control
HSM-I-04-04
-
4x4 HDMI matrix switch with RS232 and IP control. Supports HDCP, deep color, multi-channel digital audio (up to 7.1 channels), and may be used with any combination of DVI (PC) or HDMI (HDTV) sources and displays.
-
Product
PXI-2535, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-35
Matrix Switch Module
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2535 is a high-density 4x136 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring field-effect transistor (FET) relays, the PXI‑2535 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix topology With Column Protection Resistors
782385-12
Terminal Block
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
2X16 PXIe Switch Matrix, 300 KHz to 9 GHz
M9164B
Switch Module
M9164B 2X16 PXIe switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provide a switch based multiport VNA solution.
-
Product
PXI BRIC8 FIBO Matrix Dual 60x4 3pin brkout
40-592A-103
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
Product
High Power, Low PIM Switch Unit
LPSU
-
Low PIM coaxial switch matrix 5 x 6 or 1 x 4 configurationFrequency range 698-2700 MHz.SCPI commands via Ethernet (wired or wireless).Significantly reduces test time for multi frequency PIM applications.Applications: ATE systems, multi-band antenna and component testing.
-
Product
Computer Controlled, Solid-State RF Switch Matrices
-
PMI offers a full product line of RF Switch Matrices that operate over the 20MHz to 40GHz frequency range. Three standard models are offered that cover this frequency range, namely 20MHz to 3.0GHz, 2.0GHz to 18.0GHz, and 18.0GHz to 40.0GHz. Any of the three models can be supplied as either a 4 X 4, 8 X 8, 16 X 16, or 32 X 32 non-blocking matrix.
-
Product
USB Type-C Interconnects Compliance Test Software
S94USBCB
-
Use the S94USBCB software to test, debug and characterize your USB Type-C cable and connector designs. The PathWave TAP based test sequencer automates the network analyzer (VNA) for each test and generates a comprehensive HTML report. When run with L8990M switch matrix, it enables 20-ports fully automated test without port re-connection.
-
Product
Multi-Channel SMU
-
Up to 4 potential-free channels, U/I measurement unitsMax. 400 V or 100 A per channelTotal output max. 800 W (10 kW in pulse mode)Integrated switching matrix with self-testStandard: 19", 3/6 U
-
Product
PXI BRIC4 FIBO Matrix Dual 60x4 3pin brkout
40-592A-003
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
TB-2635, Screw Terminal, 8x16, 2-Wire PXI Module Matrix Terminal Block
778839-01
Terminal Block
Screw Terminal, 8x16, 2-Wire PXI Module Matrix Terminal Block - The TB-2635 provides the necessary routing to configure the PXI-2529 PXI Matrix Switch Module as a 2-wire 8×16 matrix. You can directly connect the TB-2635 to the front panel I/O connectors of the PXI-2529. The TB-2635 includes screw terminals that provide access to the rows and columns of the matrix.
-
Product
High-Power PXI Switch Matrix Modules
-
These high-power PXI switch matrix modules provide higher current and power ratings than the high-density switch versions. These modules are designed for the switching of AC or DC loads or for controlling large relay or solenoid systems. The solid state relay matrices occupy two PXI slots and are suitable for automotive and aerospace test applications.
-
Product
High-Voltage PXI Switching Matrix Modules
-
The design of our high-voltage PXI switching matrices ensures the modules can withstand high common mode voltages and a protective safety cover is used to shield the switching components.
-
Product
Solid State PIN Diode Transfer Switch, 100 MHz to 18 GHz
P9400C
-
The Keysight P9400C solid state PIN diode transfer switch offers outstanding performance in terms of port-to-port isolation, switching speed and low insertion loss over a broad operating frequency range of 100 MHz to 18 GHz. The P9400C is particularly well suited for ultra-fast RF and microwave switching applications in instrumentation, communications, radar, switch matrices and various other test systems where high isolation, speed and lifetime of a switch is critical.
-
Product
Cable/Harness Test System with Rack-Mounted Switching
CKT1175-20
-
The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system.
-
Product
LXI EMR Low Thermal EMF Matrix 42x33
60-511-002
Matrix Switch Module
This high density 1-pole matrix has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix.
-
Product
TB-2636, Screw Terminal, 4x32, 2-Wire PXI Module Matrix Terminal Block
196762-01
Terminal Block
The TB-2636 provides the necessary routing to configure the PXI-2529 PXI Matrix Switch Module as a 2-wire 4×32 matrix. You can directly connect the TB-2636 to the front panel I/O connectors of the PXI-2529. The TB-2636 includes screw terminals that provide access to the rows and columns of the matrix.
-
Product
PXI Expandable 16x16 RF Matrix 50Ohm Lemo 00
45-720A-541
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
PXI 8x4 RF Matrix 100MHz 75 SMB With Loop-Thru
40-729-101-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
LXI Low Thermal EMF Matrix 1-pole 14x33
60-510-004
Matrix Switch Module
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset. The 60-510 is designed in accordance with the LXI Standard 1.4 and is supplied in a 2U high, full rack width case with 500mm depth.
-
Product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix Topology Without Column Protection Resistors
782385-03
Terminal Block
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Switch Matrices
-
Our standard line of switch matrices includes automated control via our command customizable controller. Interface options include USB, LAN, IEEE-488, and many other options that can customize our standard switch to meet your needs. ur existing designs cover a wide array of topologies, frequencies up to 70Ghz. and power levels from milliwatts through kilowatts.
-
Product
PXI BRIC8 FIBO Matrix Dual 120x4 3pin brkout
40-592A-106
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
RF Microwave Switch Matrices
-
RF Microwave Switch Matrices provide automatic routing of RF microwave signals between test instrumentation and the unit under test (UUT). They provide consistent signal paths, enable automation of tests, and often include signal conditioning.
