Switching Matrix
expand availability of instrumentation I/O fulfilling test node array connections.
See Also: Switching, High Voltage Switching, Switching Matrices, Multiplexers, General Purpose Switch, Mass Interconnect
-
product
LXI Dual 24x8 Video Matrix, MCX (75R)
60-711-004
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75 Ohm with the option of SMB or MCX connectors or, with a larger case size, BNC connectors. It is designed to provide a simple and scalable bidirectional matrix for video frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-711 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
product
PXI 4-Slot BRIC Matrix, 29x8 2A 2-Pole (1 Sub-card)
40-565B-002-29X8
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
product
PXI BRIC4 FIBO Matrix Dual 124x4 2pin Brkout
40-592A-014
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines. Typical applications are in automotive and aerospace industries which involve safety or mission critical systems that have to behave predictably when cabling or sensor faults occur.
-
product
DC Parametric Test System with Curve Trace
DC3
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
product
PXI 8-Slot BRIC Matrix, 58X8 2A 2-Pole (2 Sub-cards)
40-565B-102-58X8
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
product
Switch Matrices
Mercury System’s family of rugged, custom-designed switch matrices are available in rigid PCB construction, module-based packages, or rack-mount solutions. Each switch matrix is a highly integrated, SWaP-optimized assembly consisting of an assortment of switches, filters, amplifiers, attenuators, limiters, and drivers. The result is high speed channel selection, high isolation, high linearity, and low insertion loss.
-
product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix topology With Column Protection Resistors
782385-10
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
PXI Switch Matrix Modules
From low density to high power - we have the PXI matrix switch modules you need. PXI matrix switch modules deliver low, medium and high-density switching of multiple channels in a single instance. They are organized in rows and columns to provide maximum flexibility, allowing you to connect any row to any column, making them ideal for routing multiple signals between your device under test and your instruments.
-
product
4x8 2 Wire USB Modular Switch Matrix
U2751A
The U2751A USB Modular Switch Matrix offers a flexible connection path between the device under test and the test equipment, thus allowing different instruments to be connected to multiple points on the device under test at the same time. This instrument is able to support measurements at a high bandwidth of up to 45MHz. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity
-
product
PXI BRIC8 FIBO Matrix Dual 31x4 2pin brkout
40-592A-111
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
product
PXI BRIC8 FIBO Matrix Dual 40x4 3pin brkout
40-592A-102
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
product
IF-Band
Quintech Electronics and Communications Inc.
A system or software used to set up and control an IF (Intermediate Frequency) switching matrix, which is a specialized piece of equipment primarily used in satellite ground stations and teleport facilities. Its main function is to automate the routing of signals.
-
product
PXI BRIC4 FIBO Matrix Dual 31x4 2pin brkout
40-592A-011
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
PXIe-2738 , 256-Crosspoint, 8x32, 2-Wire PXI Matrix Switch Module
782835-38
256-Crosspoint, 8x32, 2-Wire PXI Matrix Switch Module—The PXIe‑2738 is a high‐density 8x32 PXI matrix switch module designed for routing signals within automated test systems and using electromechanical relays to perform immediate switch operations. It also offers features to monitor the health of deployed systems and plan for predictive maintenance, including onboard relay count tracking, a temperature sensor, and functional and resistive relay self-tests available through the NI Switch Health Center.
-
product
Signal Conditioning and RF Distribution
CAES provides high performance signal conditioning and RF distribution solutions such as switch matrices for the EW, missile, radar, communications and space markets. Our custom designs offer high speed switching, low insertion loss, low harmonic level and excellent isolation.
-
product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781420-11
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
PIN Solid State Switch, 100 MHz to 18 GHz, SPDT
P9402C
The Keysight P9402C PIN solid state switch maximizes your operating frequency range from 100 MHz to 18 GHz. Providing superior performance in terms of isolation, insertion loss and return loss, the P9402C is particularly suitable for high-speed RF and microwave switching applications such as switch matrixes in instrumentation, communications and radar. These switches provide ultra-fast switching speed to increase throughput in manufacturing.
-
product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix Topology Without Column Protection Resistors
782385-03
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
PXI 2-Slot BRIC Matrix, 29x8 2A 2-Pole (1 Sub-card)
40-565B-202-29X8
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
product
SWB-2810, 4x43, 1 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-10
4x43, 1 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
RF Switch Matrix
Compact, low-insertion-loss, non-reflective microwave switches. USB controlled and powered with optional Ethernet and audio feedback.
-
product
High Voltage Cable/Harness Test System
CKT1175-50
The CKT1175-50 is a high-voltage wiring analysis system that features a switching matrix that can be distributed around the workshop or in and around the assembly to be tested. This system is expandable in 100 or 150 test point increments to 96,000 test points, and is available with a variety of adapter cable interface connectors, with the standard being the CKT MAC interface system
-
product
High-Voltage PXI Switching Matrix Modules
The design of our high-voltage PXI switching matrices ensures the modules can withstand high common mode voltages and a protective safety cover is used to shield the switching components.
-
product
PXIe-2540, 350 MHz, 8x9 PXI RF Matrix Switch Module
780587-40
PXIe, 350 MHz, 8x9 PXI RF Matrix Switch Module—The PXIe‑2540 is an RF signal switching matrix. With its non-blocking design, you can simultaneously connect any row or column within the switching matrix and maximize the flexibility of your test system. Isolation relays on the module disconnect unused parts of the switching matrix to maintain RF performance and high isolation. The density and bandwidth of the PXIe‑2540 is ideal for routing signals between digitizers, function generators, and other RF generators and analyzers.
-
product
Modular RF Systems
Becker Nachrichtentechnik GmbH
Flexible modular system for customer specific system solutions without the effort of development and construction. The range of module types covers from active multicouplers, programmable attenuators, delay lines, RF switches, switching matrices, BIAS-Ts, RF filters up to bi-directional splitters and combiners.
-
product
PXI Solid-State Matrix Module, 6x2, 10 A
40-553A-011
The 40-553A-011 is a high current 6x2 matrix occupying two slots of PXI chassis. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each matrix switching path can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
LXI Scalable Switched Guard Matrix - 16x16 Plugin Module
65-290-001
The 65-290-001 ia a 16x16 matrix plug-in module for use in Pickering's modular switching platform that provides a switched guard relay matrix solution with up to 1012 Ω channel to channel and channel to ground isolation.
-
product
Matrix Switches
JFW offers blocking and non-blocking matrix switches. They are available with 50 Ohm or 75 Ohm impedance. The Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted commands. Our RF Matrix Guide steps through the advantages for each matrix type.
-
product
Single Mode Low Loss All Optical Switch From 8x8 To 192x192 Ports
SERIES 6000
The Polatis Series 6000 Network Optical Switch is a high-performance, fully non-blocking all-optical matrix switch available in sizes from 8x8 up to 192x192. It is designed to meet the highest performance and reliability needs of the most demanding applications with exceptionally low optical loss, compact size, low power requirements and fast switching speeds. With support of Software-Defined Networks (SDNs) via an embedded NETCONF and RESTCONF control interfaces, the Series 6000 enables extremely low latency for time-critical traffic required for new virtual cloud services in hybrid packet-optical data centers. The Series 6000 is based on Polatis’ patented DirectLight® optical switching technology that has been proven in the most challenging data center, telecom and defense applications and is also used by major network equipment manufacturers to automate testing of optical components and subsystems.
-
product
PXI-2533 , 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-33
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2533 is a high-density 4x64 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2533 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
