Noise Monitors
-
product
Ship Auxiliary System Monitor
A distributed system consisting of a variable number of intelligent measuring units, a central computer located on board a ship, and a remote computer on the shore, with the ability to configure and analyze measured signals via the Internet. Intelligent measuring units are built on the basis of the industrial measuring platform PXI.
-
product
Ballast Water Monitoring Systems
Ballast water is essential for safe and efficient shipping operations and stabilizing steel-hulled vessels at sea. It provides a variety of critical functions, such as maintaining balance, stability, and structural integrity on non-cargo voyages or when cargo is unloaded. Ballast water is also used to compensate for fuel and water consumption during at-sea operations.
-
product
Electrostatic ESD Voltmeters & Monitors
Many applications require the measurement of a voltage or electrostatic charge on surfaces. Given the fact that the buildup of electrostatic charge during handling, manufacturing, assembly and other operations can impact production capacity and quality, ETS enables tests on stationary or moving surfaces.
-
product
Ammonia Monitor
Chillgard® 5000 Ammonia Monitor
The Chillgard 5000 Ammonia Monitor accurately detects ammonia gas leaks as low as 10 ppm for early notification, keeping your plant safe according to ANSI/IIAR and EN 378.
-
product
Low Noise Test Leads For N1413 With B2980 Series, 3m
N1425B
The N1425B is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425B is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425B enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425B to the B2985B/87B.
-
product
Digital Light Monitor
LMC-20
The LMC-20 functions not only as a light monitor for coating thickness, but also allows control of multi layer/multi material coating processes. Up to 2000 individual layers in a coating are possible, by using 40 program banks of 50 layers each. The characteristics of up to 99 different coating materials can be input as well. Final thickness can be calculated to 1% of a quarter wave.
-
product
Circuit Breaker Monitoring
Circuit Breaker monitoring for all parameters required to accurately monitor the overall health and performance of circuit breakers
-
product
Tower Light Monitor
1750-TLM
Designed with the Broadcaster in mind the 1750-TLM provides built in flexibility to simplify even the most complicated installations. It can even alarm for single bulb failures on towers with Beacons and Obstruction lights on a single circuit. Status oututs eliminate the worry of operator interpretation and provide definitive Good-Bad indications for the operator and your logging equipment. Don’t let tower light failures expose you to increased liability, the 1750-TLM is compatible with most existing control equipment and may well provide your best return on investment this year!
-
product
Charged Plate Monitor
Model 280A
Simco-Ion’s Model 280A incorporates enhanced circuitry that enables it to more accurately measure the performance of high frequency AC ionizers, as well as pulsed DC ionizers and steady-state DC ionizers. The Model 280A can be used as a portable CPM and is capable for of up to 6 hours of operation on the internal battery before recharge.
-
product
Noise Assessment System For Noise At Work
NK013
This Noise Assessment System for Noise at Work provides you with everything you need to perform assessments to The Control of Noise at Work Regulations 2005, at an incredible price.
-
product
RF Safety Monitoring
MVG EME Guard XS Radar
Specifically designed to alert workers operating near radar transmitters of RF exposures, the unique EME Guard XS Radar is an RF pulse measuring device. It continuously scans for short pulsed signals, and via its built-in alarm and visual system, alerts users whenever the acceptable limits have been exceeded. This RF Safety tool is extremely easy to use and creates a safer working environment close to radar antennas and other pulsed RF sources.
-
product
C/Ku Band Satellite Monitoring
SCL-3412
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
-
product
Precision Calibrated Noise Sources
ELVA-1's calibrated noise source ISSN-XX series delivers a uniform level of noise power spectral density within the whole waveguide frequency range. Sources are available in eight waveguide bands covering 26.4-170 GHz.
-
product
Environmental Monitoring
Life doesn't stand still and neither do you. An amazingly intuitive web-based control panel gives you the freedom to monitor environments from anywhere.
-
product
Monitoring and Control System for Elevators and Escalators
The software package developed in the MS Visual C ++ environment has an attractive and an intuitive graphical interface. It provides for work with several groups of equipment controllers, provides advanced analysis and control capabilities (building equipment management, passenger traffic analysis, recording and playback of diagnostic information).
-
product
Ohm-Stat Guardian Pro Constant Monitor
Tests two people and two wriststrapsLED and buzzerNIST calibration includedWorks with all single wire capacitance wrist strapsAll cords suppliedCE markCan be calibratedProduct conforms to the ESD S.20.20 spec standards110v AC powerGround dock included
-
product
Ultra Low Noise Preamp
J2180A
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
product
PXI Monitored Multiplexer, Single 128-Channel, 1-Pole
40-619-401
The 40-619-401 is a high density PXI 2 A multiplexer module in single 128-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
product
Charge Plate Monitors
Our charge plate monitors the voltage of the battery and the voltage of the battery.
-
product
Optical Performance Monitor
Optoplex Optical performance monitor (OPM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical performance monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controlling network elements so as to optimize operational performance. In particular, Optoplex Optical performance monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength and power. See the following schematic diagram for OPM working principle.
-
product
Advanced Monitoring Probe
DVB-T/T2
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-T and DVB-T2 signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
product
Network Traffic Monitoring Software
Network Traffic Monitor or NetFlow Analyzer, primarily a bandwidth monitoring tool, lets you check and monitor your bandwidth / traffic pattern and determine, how network bandwidth is being utilized. Get real-time insights into bandwidth usage or the amount of network traffic caused by IP addresses, protocols, or programs. Create customized reports like Top Applications by Traffic, Top Conversations by Traffic, Top Traffic Destinations by Host IP, Top Traffic Sources by IP address, Top Traffic Receivers by IP and more.
-
product
USB Smart Noise Source, 500 MHz To 50 GHz, 5 DB ENR Nominal
U1832C
The USB-powered (USB TMC compliant) U1832C provides broadband noise figure measurements from 500 MHz – 50 GHz with modular signal analyzer, benchtop X-Series signal analyzers and Fieldfox
-
product
Unify Monitoring
Explore the possibilites with our unified software-based monitoring tools. From live broadcast sources to OTT streams, our comprehensive solutions provide control from standard PCs and mobile devices.
-
product
Audio Loudness Monitoring And Logging System
The Mividi® Audio Loudness Monitoring and Logging System (Loudness Logger) provides a cost-effective solution for broadcast compliance monitoring and logging. It is a Windows PC based system that supports audio decoding, loudness monitoring and logging, log file management and playback. It takes transport stream input from UDP over IP or ASI interfaces, as well as Internet OTT streaming input using HLS, RTMP, RTSP, and MPEG-DASH protocols. A single system can support continuous monitoring and recording over 50 channels simultaneously.
-
product
Noise Source, 10 MHz to 26.5 GHz, nominal ENR 15 dB
346C
The Keysight 346C noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 26.5 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. Option K01 is a coaxial noise source and features coverage from 1 to 50 GHz with a 2.4 mm coaxial connector.
-
product
Monitor / Annunciator
RTP-1
The RTP-1 Monitor is a general purpose annunciator. Designed for 19 “ rack installations, the RTP-1 is complete with a noise immune filter. The ten point RTP-1 features latching memory. Easy to install and easy to operate, this low power monitor has front panel plug-in replaceable LEDs for indication and a single system Test and Reset buttons.
-
product
Mill & Silo Monitoring System
MSM-100
MSM-100 is a monitoring system specifically designed to continuously detect carbon monoxide(CO) in pulverizing mills. The high level of CO produced by any incomplete combustion process, is used by the MSM-100 system as advance warning of a mill fire. It is suitable for any coal or peat system where advance warning of spontaneous combustion is required. MSM-100 is intended for operation in the electricity, metals, cement, steel and processing industries.





























