Noise Monitors
-
Product
High-Power Noise Sources
-
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
Product
IMPATT Noise Generator CW & Pulse At W-band, 94 GHz :
-
The device consists of two modules, a cable that connects them, and a power cable. The first module (I) contains the power supply (AC 115 V), regime switch mechanism and a generator of a series of pulses. The second module (II) is the noise generator. Photo 1: Module I - Power Supply
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
Conductivity / TDS Monitor / Controllers
750 Series II Conductivity Monitor & Controllers
-
The unique circuitry of the 750 Series II Conductivity Monitor/controllers guarantees accurate and reliable measurements. Drift-free performance is assured by “field proven” electronics, including automatic DC offset compensation and highly accurate drive voltage. Since temperature compensation is at the heart of accurate water measurement, all Myron L® Monitor/controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. The TC may be disabled to conform with USP requirements.
-
Product
Backup Battery Monitor And Switch
-
Renesas offers an automatic battery back-up switch, intended as a low-cost solution for the switching of systems between two power supplies; main and battery backup.
-
Product
Network and Application Monitoring
IxChariot
-
Instant performance assessment of complex networks from pre- to post-deployment
-
Product
Noise Dosimeter
SV 104
-
The SV 104 is our latest and smallest ever noise dosimeter. It has incredible functionality, taking full noise dosimeter capabilities into a compact style instrument that beats anything else on the market hands down!Any instrument is only as strong as its weakest point and on a noise dosimeter that's normally the microphone. On the SV 104 we've removed that 'Achilles heel' by using a revolutionary and virtually indestructible MEMS microphone.
-
Product
Flexible Monitoring of Voltage & Current in A 2 B ® Networks
Line Test Box LTB 1024
-
The Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. reduces the complexity of audio systems. In addition to the automotive industry, it is also increasingly being used in other areas such as conference systems. We have developed a line measuring device specifically for this A 2 B ®technology: the Line Test Box LTB 1024.
-
Product
Portable 4-channel Noise & Vibration Analysis System
WCAmini AD-3661
-
* USB bus power unit * 24 bit, 4-channel measurement * A channel exclusively for tacho pulse measurements * WCAPRO (multi analysis software) * FFT analysis and real-time octave analysis * Tracking analysis and throughput recording/playback * Equipped with WCA Lite (easy-to-use analysis software)
-
Product
General Noise & Vibration
-
NVGate, the software platform is the cornerstone for all measurement tasks. It hosts the suite of OROS software modules. Whatever the application and software module, it allows you working in a coherent and continuous environment.
-
Product
QoS Monitor
Arptel Monit
-
The Arptel Monit is a cost-effective and flexible network monitor solution for telcos. The Arptel Monit is a powerful tool for monitor QoS on live international and domestic traffic.
-
Product
DC Insulation Monitor
ISM-200
-
Kongter Test & Measurement Co., Limited
ISM-200 Insulation monitoring system is a high accurate and secure online monitoring equipment for DC system insulation. It is designed for the measurement of different types of ground fault, insulation decreasing, AC signal interruption, DC signal interruption and so on.
-
Product
Noise Reduction
-
Applied Research and Technolgy
Eliminate ground hum with our specialized transformers and isolators.
-
Product
Dust Monitors
-
Kanomax USA offers highly accurate and convenient dust monitors for various applications, including our Digital Dust Monitor and Piezobalance Dust Monitor. These instruments provide solutions for things like construction dust monitoring, machining particle monitoring, and oil mist monitoring.
-
Product
Real Time Monitoring Of Windows Server
GSX for Windows Server
-
Monitor and troubleshoot operating systems and related applications from a single dashboard. Windows servers and services are fueling mission-critical applications, so having visibility into the status of their health and usage is essential. By continuously testing the availability and performance of the Windows server and its applications, GSX enables proactive management of the IT environment. End-to-end monitoring improves the end-user experience, reduces mean-time-to-repair, and helps administrators to prevent issues before they happen.
-
Product
Hydrofluoric Acid Monitor
CM-200A/210A
-
The CM-200A/210A hydrofluoric acid monitors have been developed specifically to meet the stringent demands of semiconductor manufacturing. The CM-200A/210A provides a real time read-out of hydrofluoric acid concentration by measuring the electric conductivity of the sample solution. These superior units offer high repeatability even at low concentrations. The CM-200A/210A can be used for a variety of purposes ranging from monitoring etched wafer cleaning processes to any other industrial application of hydrofluoric acid.
-
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Portable Sulphuric Acid Dewpoint Temperature Monitor
-
The fuels used in boilers, such as coal, heavy oil and natural gas, contains S. during the combustion process, S and O₂ form SO₂, and a small amount of SO₂ is converted into SO₃ under catalysis of Fe₂O₃, V₂O₅ and other catalysts. Under normal circumstances, the volume of SO₃ in the boiler flue gas is 1×10-6～50×10-6, and the water vapor is about 10%. When the temperature of the flue gas is below 200°C, SO₃ and the water vapor are completely combined into H₂SO₄ vapor. A small amount of H₂SO4 vapor will significantly increases the acid dew point. When the surface temperature of the boiler heat exchange equipment is lower than the flue gas acid dew point, the H₂SO₄ vapor will condense on the surface to become sulfuric acid solution with a concentration of about 80%, which will adhere to the surface of the heat exchanger and cause acid corrosion. Typical equipment that is prone to corrosion includes air preheaters, induced draft fans and flue walls.
-
Product
Network Performance Monitoring
NetVCR®
-
Powered by groundbreaking technologies, NIKSUN NetVCR® redefines the way we monitor networks. It provides seamless service and application performance analytics for maximum visibility into your on-premises, cloud, or hybrid environments. NIKSUN NetVCR® gives you unmatched insight while still dramatically reducing power consumption by 60% and requiring 80% less rack space.
-
Product
Cryogenic Temperature Monitors
-
Monitor temperatures from 1.4K to over 800K. Choose from one or eight standard inputs. USB, IEEE-488, and RS-232C interfaces, relays, and analog outputs are available.
-
Product
Power Monitoring Dynamometer
90085
-
Model 90085 is designed to measure machine tool output. This model acquires the necessary torque and speed data needed to calculate the horsepower of the machine tool under test conditions. It is a portable, self-contained data acquisition and monitoring system consisting of three major components: a pneumatic brake assembly, a torque and speed transducer, and the control and display module.
-
Product
Radiation Monitor
-
The Radiation Monitor is the survey meter in measuring the beta, gamma and x-ray radiation. It is useful in monitoring the environment/home safety, nuclear, medical, mining and metal industries. It is also ideal for the border control, customs and cargo inspections.
-
Product
Advanced Active/Passing Monitoring System
SQmediator
-
SQmediator® is an advanced active/passive monitoring system engineered to proactively manage the end-to-end performance of a range of network applications, including Voice over IP, IP Videoconferencing, Web and Email. Its multi-service, multi-tenant architecture supports advanced data aggregation, one-click custom dashboards for customers and locations, per-metric service thresholds, real-time alerts, and a web services API for integration with external management systems
-
Product
Single Phase Powerline Monitors
-
a Voltage disturbance detector and recorder. This device is designed to be plugged into a 120V or 240V AC line and will monitor this line for voltage disturbances and temperature or Humidity variations.
-
Product
Monitor Debugger/RAM Monitor
-
The Monitor Program is automatically written to the MCU when the Debugger is started up.
-
Product
Continuous Surface Current Mapping & Wave Monitoring System
SeaSonde
-
The SeaSonde HF radar system by CODAR Ocean Sensors is your solution for making continuous, wide-area ocean observations. The SeaSonde will provide you with years of real-time data over large coverage areas, with ranges up to 200 km — This is not possible with any other technology!
-
Product
Optical Fiber Type Hot Phosphoric Acid Concentration Monitor
CS-620F
-
In 3D NAND manufacturing process, dozens of layers of SiO2 and SiN are deposited, and the SiN layer is selectively removed using hot phos.In this process, the desired etching rate can be achieved by controlling the concentration and temperature of the chemical solution.Previous products have difficulty to measure high temperature chemicals, but the CS-620F is able to measure at high temperatures up to 170 C degrees.
-
Product
PRO Conductivity (EC) Monitor
MC310
-
The Milwaukee MC310 PRO Conductivity (EC) monitor lets you measure EC levels automatically and alerts with an alarm when out of the set point range.
-
